• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.35-41
• /
• 1988

In the system of Li2O-MgO-Al2O3-Cr2O3, the crystalline solid solution of LiCrO2 along the pseudo-binary join between rocksalt structure(LiCrO2) and spinel structure(MgCr2O4 or MgAl2O4) have been investigated by x-ray diffraction techniques. In this study, order-disorder phase transition of LiCrO2 was observed and the unit cell of the disordered LiCrO2 structure has been established. It has been found that LiCrO2 makes a solid solution over a wide range with MgAl2O4, while not with MgCr2O4. This difference was explained as being due to the ability of oxygen lattice distortion which depended on the relative sizes and chemical bonding characteristics of the substituted ions.

• Journal of the Korean Chemical Society
• /
• v.43 no.4
• /
• pp.418-422
• /
• 1999

A method is described for the selective determination of Cr(III) and Cr(VI) in aqueous solutios by flame atomic absorption spectrometry. Selective extraction of $Cr_2O_7^{2-}$ was performed by Aliquat 336/NIBK from the mixtures of $Cr^{3+}$ and $Cr_2O_7^{2-}$, and the extraction of $Cr^{3+}$ was followed after complex formation with citrate by using the same extractant. The concentraction of each analyte in the extract was determined by $N_2O-C_2H_2$ flame atomic absorption spectrometry. The recoveries of $Cr^{3+}$ and $Cr_2O_7^{2-}$ from 50mL of aqueous solution ranging 0.1~1.0 ${\mu}g/mL$ as Cr respectively by single extractions with 5 mL of 1%(V/V) Aliquat 336/MIBK were resulted as 98.8∼101.7%.

• Korean Journal of Materials Research
• /
• v.8 no.9
• /
• pp.849-855
• /
• 1998

The purpose of this study was performed to compare to the characteristics (microstructure, phase change and hardness, erosion rate) of HVOF sprayed coatings with 20wt% NiCr claded and 7wt%NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ powder. In the case of the 20wt% NiCr claded $\textrm{Cr}_{3}\textrm{C}_{2}$ powder, microstructural feature showed that the primary $\textrm{Cr}_{3}\textrm{C}_{2}$ was remained in the coating but was barely remained in the mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ coating. As a results of XRD analysis, both 20wt%NiCr claded and 7wt% NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ powder was decomposed during spraying but the degree of decomposition of the 20wt%NiCr claded was lower than 7wt%NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ powder. After spraying the mixed powder for microhardness was higher than claded $\textrm{Cr}_{3}\textrm{C}_{2}$ powder and which was increased up to $\textrm{Hv}_{300}$= 1665 after heat treatment to $1000^{\circ}C$. however. 20wt%NiCr claded $\textrm{Cr}_{3}\textrm{C}_{2}$ became to decrease at $600^{\circ}C$ which was the maximum.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.757-765
• /
• 1998

This study was performed to investigate the influence of fuel/oxygen ratio (F/O= 3.2, 3.0, 2.8) on the oxidation behavior of two kinds of (20wt%NiCr claded $\textrm{Cr}_{3}\textrm{C}_{2}$, and 7wt%NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$) composite powder with different manufacturing method. The results show that the oxidation behavior between the 20wt% NiCr claded $\textrm{Cr}_{3}\textrm{C}_{2}$ and 7wt% NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ coating was widely different. The surface morphology of the coating composed of 7wt% NiCr mixed $\textrm{Cr}_{3}\textrm{C}_{2}$ was changed to porous with F/O ratio by the aggressive evolution of gas phases($\textrm{CO}_2$, CO and $\textrm{CrO}_3$) and the oxide cluster composed of Ni and Cr were grown after oxidation at $1000^{\circ}C$ for 50 hours. But the surface morphology of the coating composed of 20wt% NiCr claded $\textrm{Cr}_{3}\textrm{C}_{2}$ was not changed to porous after oxidation at $1000^{\circ}C$ for 50 hours. Therefore, the reason for high oxidation rate is due to activation of $\textrm{Cr}_{3}\textrm{C}_{2}$ to oxidation by entrapped oxygen gases within coating layer, and to closely relate with the decomposition of $\textrm{Cr}_{3}\textrm{C}_{2}$ to $\textrm{Cr}_{7}\textrm{C}_{3}$ phase. Accordingly, On the evidence of these results, the study about the oxidation behavoir of the HVOF sprayed $\textrm{Cr}_{3}\textrm{C}_{2}$ coating depending on hydrogen flow rate must be done.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.126-135
• /
• 1997

$H_2/O_2$ 비에 따른 Hybrid HVOF 용사된 $Cr_3C_2$-7wt%(NiCr) 용사층의 특성 및 산화거동 This study was performed to investigate the influence of fuel/oxygen ratio (F/O=3.2, 3.0, 2.8) on the characteristics and the oxidation behavior of the hybrid-HVOF sprayed $Cr_3C_2$-7wt%NiCr coatings. Decomposition and the oxidation of the $Cr_3C_2$was occured during spraying. The degree of transformation from $Cr_3C_2$to $Cr_7C_3$ was increased with decreasing the F/O ratio. The microstructural differences of the as sprayed coating with F/O ratio can not be distinguished, However, large pores were diminished and then the coatings became dense by heat treatment. Microhardness of the as-sprayed specimen which sprayed with F/O=3.0 condition was hightest ($Hv_{300}$=1140) and the hardness was increased to 1500 after heat treatment at $600^{\circ}C$ for 50hrs in air. It was supposed that hardness was increased due to the formation of $Cr_2O_3$ within $Cr_3C_2$/$Cr_7C_3$matrix and the densification of coating layer during heat treatment. Apparent activation energy for oxidation was varied from 21.2 kcal$mol^{-1}K^{-1}$ to 23.8 kcal$mol^{-1}K^{-1}$ with respect to the F/O ratio. The surface morphology was changed to porous and oxide chusters were grown after oxidation $1000^{\circ}C$ for 50 hours by the aggressive evolution of gas phase ($CrO_3$ and$CO_2$). The oxide cluster was composed of Ni and Cr.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.33-35
• /
• 2011

Films of CrAlN and CrZrN were deposited on a steel substrate by closed field unbalanced magnetron sputtering, and their oxidation behaviors were investigated. CrAlN films consisted of dense, polycrystalline CrN and AlN fine columns. The formed oxides consisted primarily of crystalline $Cr_2O_3$ incorporated with $Al_2O_3$. The oxide layers were thin and compact so as to make CrAlN films more protective than CrN films. In case of CrZrN films, Zr atoms were dissolved in the CrN phase. Zr atoms advantageously refined the columnar structure, reduced the surface roughness, and increased the micro-hardness. However, the addition of Zr did not increased oxidation resistance, mainly because Zr was not a protective element. All the deposited films displayed relatively good oxidation resistance, owing to the formation of the highly protective $Cr_2O_3$ on their surface. The $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films oxidized to $Cr_2O_3$ as the major phase and ${\alpha}-ZrO_2$ as the minor one, whereas the CrN film oxidized to $Cr_2O_3$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.63-69
• /
• 1997

The effects of Cr2O3 content on the properties of direct-bonded MgO-Cr2O3 bricks were investigated in the range of 10 to 30 wt% of Cr2O3. Modulus of rupture of bricks was excellent in about 20 wt% of Cr2O3 content. The corrosion resistance of bricks was improved by increasing Cr2O3 content and was directly pro-portional to the amount of secondary spinels. On the other hand, the spalling resistance of bricks depended on the amount of flux rather than Cr2O3 content.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.39-43
• /
• 2007

The pure CrN powders oxidized to $Cr_2O_3$ noticeably above $850^{\circ}C$ in air. When these powders were sintered into bulk samples at $1500^{\circ}C$ under 40 atm of $N_2$ pressure, the CrN phase partly changed into the $Cr_2N$ phase, owing to the partial loss of nitrogen from CrN. When the bulk sample was heated at $1000-1200^{\circ}C$ for 100 hr under vacuum, the CrN phase also progressively changed into $Cr_2N$. At the same time, a relatively thin $Cr_2O_3$ layer formed on the bulk sample due to the reaction of chromium with residual oxygen in vacuum.

• Korean Journal of Materials Research
• /
• v.31 no.11
• /
• pp.635-641
• /
• 2021

Cr thin films with O added are deposited on sapphire substrate by DC sputtering and are nitrided in NH₃ atmosphere between 300 and 900 ℃ for various times. X-ray diffraction results show that nitridation begins at 500 ℃, forming CrN and Cr₂N. Cr oxides of Cr₂O₃ are formed at 600 ℃. And, at temperatures higher than 900 ℃, the intermediate materials of Cr₂N and Cr₂O₃ disappear and CrN is dominant. The atomic concentration ratios of Cr and O are 77% and 23%, respectively, over the entire thickness of as-deposited Cr thin film. In the sample nitrided at 600 ℃, a CrN layer in which O is substituted with N is formed from the surface to 90 nm, and the concentrations of Cr and N in the layer are 60% and 40%, respectively. For this reason, CrN and Cr₂N are distributed in the CrN region, where O is substituted with N by nitridation, and Cr oxynitrides are formed in the region below this. The nitridation process is controlled by inter-diffusion of O and N and the parabolic growth law, with activation energy of 0.69 eV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.373-373
• /
• 2010

광촉매능을 갖는 $TiO_2$는 국내외적으로 많은 연구가 진행되고 있다. 빛의 조사로 발생하는 다양한 물리 화학적 촉매특성이 환경정화 뿐만 아니라 및 에너지 흡수차단 기능도 갖고 있어 최근 주목을 받고 있다. 응용분야로 초친수성 유리제품, 필터, 살균기능의 의료용 부품소재, 고효율 수소생산 및 태양전지 등에 활용성이 커서 친환경에너지 소재로 각광을 받고 있다. 본 연구에서는 초친수성 자동차의 사이드미러 개발을 위해 유리표면에 초친수성 $TiO_2$를 코팅하 고 그의 특성을 평가하였다. 특히, 이종밴드갭을 갖는 복합구조 $TiO_2/Cr_2O_3$/Cr 박막을 스퍼터링법으로 증착하여 중간층인 $Cr_2O_3$의 역할을 고찰하였다. 제조된 박막의 결정구조는 thin film형 X-선회절기(XRD)를 사용하여 분석하였으며, 박막의 표면 미세구조는 FE-SEM(Field Emission Scanning Electron Microscope)와 AFM(Atomic Force Microscope)으로, 화학구조는 XPS(X-ray Photoelectron Spectroscope)로 분석하였다. 친수성 평가는 실온 분위기에서 접촉각 측정기(Topcon-UVR2)를 사용하여 평가 하였으며 이때 조사되는 UV는 파장이 365nm이다. $Cr_2O_3$(비정질)/Cr박막위에 제조된 $TiO_2$ 박막은 균일한 anatase-$TiO_2$가 성장했으나, Cr, $Cr_2O_3$(결정질)박막위에 제조 된 $TiO_2$ 박막은 anatase상과 rulile상이 혼합된 형태로 성장하였다. $TiO_2$/Cr, $TiO_2/Cr_2O_3$(비정질)/Cr, $TiO_2/Cr_2O_3$(결정질)/Cr박막은 UV조사 1시간 만에 $10^{\circ}$ 이하의 초친수성을 나타내었다. 이종 밴드갭을 갖는 $TiO_2/Cr_2O_3$(비정질)/Cr박막은 40시간까지 친수성을 유지하는 결과를 나타냈다.