• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• Korean Journal of Materials Research
• /
• v.15 no.9
• /
• pp.585-588
• /
• 2005

Titanium and Titanium alloys are widely used as an orthopedic and dental implant material because of their excellent biocompatibility and mechanical strength. In this study, ECAP Cp-Ti and Cp-Ti were heat treated for different annealing time of 30 min, 90 min and 3 hours. The grain size for each condition was studied. The micro-Vicker hardness test was carried out f3r each different heat treated samples. The micro-Vicker hardness test for ECAP Cp-Ti, Cp-Ti and Cp-Ti (3hr) revealed hardness values of 239.5, 182 and 144 Hv, respectively. The grain size was increased from approximately $70{\mu}m\;to\;300{\mu}m$ with the increase in heat treatment time from 30 min to 3 hours. The heat treated samples were tested for their biocompatibility in simulated body fluid (SBF) and corrosion rates was determined using Polarization Curve test (PCT). The PCT results showed Cp-Ti with comparatively high corrosion potential of -0.18 V and corresponding corrosion current of $2\times10^{-6}$ A, while the corrosion rate in ECAP Cp-Ti and Cp-Ti (30 min annealed) showed very similar results of corrosion potential about -0.47 V with corresponding corrosion current of $7\times10^{-8}$ A.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.1
• /
• pp.179-185
• /
• 2000

In this study, we examined the movement of chlorophenol as a precursor of the dioxin in the after-combustion to minimize the creation and emission of dioxin in a municipal waste incinerator. The CPs was injected to the electric incinerator in temperature $300{\sim}500^{\circ}C$, using $N_2$ gas to control the reaction time, The oxygen quantity supplied into the $CP_s's$ isomer combustion was added with the value of experience formula. When the space velocity in reactor was 60~80/sec, the removal efficiency of CP was obtained in the presence of Mo-V catalyst and non catalyst. The efficiency in non-catalyst was 74% to 80% mono-CP, di-CP 55~66%, tri-CP 50~58%, while mono-CP 90~99.9%, di-CP 96~97%, tri-CP 76~99% in a catalyst. Consequently, it was shown that these were 20~30% more efficienct than those.

• Korean Journal of Materials Research
• /
• v.14 no.12
• /
• pp.893-899
• /
• 2004

Even though Ti-6Al-4V has gained popularity as an implant material, the possible dissolution of Al and V ions in body fluids remains a matter of concern. Though commercially pure Ti (Cp-Ti) overcomes this problem, the mechanical strength of pure titanium remains very low. Thus, in this experiment Cp-Ti was processed by Equal channel angular processing (ECAP), in order to increase the mechanical strength. The biocompatibility of ECAP-Ti, Cp-Ti and Ti-6Al-4V was examined by the apatite formation on each sample surface, after treating the surface with 5M NaOH and soaking in Simulated body fluids (SBF). Initially, the samples were mechanically polished on silicone carbide paper (#2000). The polished samples were treated with 5M NaOH solution at $60^{\circ}C$ for 24 hours. The NaOH treated samples were washed gently with distill water and dried at $40^{\circ}C$ for 1 day. The dried samples were heat treated in air at $600^{\circ}C$ for 1 hour. The surface morphology of these samples were studied using SEM and XRD. The SEM studies showed network of pores in all samples. The XRD showed oxide layer formation on Cp-Ti and Ti-6Al-4V. samples. However the oxide layer in ECAP-Ti was not substantial. These samples were immersed in SBF, kept at $36.5^{\circ}C$ for seven days period. At the end of 7 days, the apatite formation was confirmed only on Cp-Ti and was not observed in Ti-6Al-4V and ECAP-Ti. These observations of apatite formation relate to the fact that Cp-Ti showed greater oxide layer than other samples. The apatite examined was confirmed as tricalcium phosphate (TCP) using EDS and XRD.

• Animal Bioscience
• /
• v.36 no.8
• /
• pp.1263-1273
• /
• 2023

Objective: This study was conducted to evaluate the effects of crude protein (CP) levels on the physiological response, reproductive performance, blood profiles, milk composition and odor emission in gestating sows. Methods: Seventy-two multiparous sows (Yorkshire×Landrace) of average body weight (BW), backfat thickness, and parity were assigned to one of six treatments with 10 or 11 sows per treatment in a completely randomized design. Experimental diets with different CP levels were as follows: i) CP11, corn-soybean-based diet containing 11% CP; ii) CP12, corn-soybean-based diet containing 12% CP; iii) CP13, corn-soybean-based diet containing 13% CP; iv) CP14, corn-soybean-based diet containing 14% CP; v) CP15, corn-soybean-based diet containing 15% CP; and vi) CP16: corn-soybean-based diet containing 16% CP. Results: There was no significant difference in the performance of sow or piglet growth when sows were fed different dietary protein levels. Milk fat (linear, p = 0.05) and total solids (linear, p = 0.04) decreased as dietary CP levels increased. Increasing dietary CP levels in the gestation diet caused a significant increase in creatinine at days 35 and 110 of gestation (linear, p = 0.01; linear, p = 0.01). The total protein in sows also increased as dietary CP levels increased during the gestation period and 24 hours postpartum (linear, p = 0.01; linear, p = 0.01). During the whole experimental period, an increase in urea in sows was observed when sows were fed increasing levels of dietary CP (linear, p = 0.01), and increasing blood urea nitrogen (BUN) concentrations were observed as well. In the blood parameters of piglets, there were linear improvements in creatinine (linear, p = 0.01), total protein (linear, p = 0.01), urea (linear, p = 0.01), and BUN (linear, p = 0.01) with increasing levels of dietary CP as measured 24 hours postpartum. At two measurement points (days 35 and 110) of gestation, the odor gas concentration, including amine, ammonia, and hydrogen sulfide, increased linearly when sows fed diets with increasing levels of dietary CP (linear, p = 0.01). Moreover, as dietary CP levels increased to 16%, the odor gas concentration was increased with a quadratic response (quadratic, p = 0.01). Conclusion: Reducing dietary CP levels from 16% to 11% in a gestating diet did not exert detrimental effects on sow body condition or piglet performance. Moreover, a low protein diet (11% CP) may improve dietary protein utilization and metabolism to reduce odor gas emissions in manure and urine in gestating sows.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.983-987
• /
• 2010

In order to investigate the emission characteristics of the phosphorescent white organic light-emitting diodes (PHWOLEDs) according to various hole transport layers (HTLs), PHWOLEDs composed of HTLs whose structure are NPB/TCTA, NPB/mCP and NPB/TCTA/mCP, two emissive layers (EMLs) which emit two-wavelengths of light (blue and red), and electron transport layer were fabricated. The applied voltage, power efficiency, and external quantum efficiency at a current density of $1 mA/cm^2$ for the fabricated PHWOLEDs were 7.5 V, 11.5 lm/W, and 15%, in case of NPB/mCP, 5 V, 14.8 lm/W, and 13.7%, in case of NPB/TCTA, and 5.5 V, 14.6 lm/W, and 15%, in case of NPB/TCTA/mCP in the hole transport layer, respectively. High emission efficiency can be obtained when the amount of hole injection from anode is balanced out by the amount of electron injection from the cathode to EML by using NPB/TCTA/mCP structured HTL.

• Animal Bioscience
• /
• v.36 no.8
• /
• pp.1228-1240
• /
• 2023

Objective: This experiment was conducted to evaluate the effects of different levels of dietary crude protein (CP) on growth performance, blood profiles, diarrhea incidence, nutrient digestibility, and odor emission in weaning pigs. Methods: A total of 240 weaning ([Yorkshire×Landrace]×Duroc) pigs (8.25±0.050 kg body weight [BW]) were assigned to six treatments based on sex and initial BW, with five replicates of eight pigs per pen in a randomized complete block design. Experimental diets with different crude protein levels for early and late weaning phases were as follows: i) CP16, corn-soybean-based diet containing 16%/15% CP; ii) CP17, corn-soybean-based diet containing 17%/16% CP; iii) CP18, corn-soybean-based diet containing 18%/17% CP; iv) CP19, corn-soybean-based diet containing 19%/18% CP; v) CP20, corn-soybean-based diet containing 20%/19% CP; and vi) CP21, corn-soybean-based diet containing 21%/20% CP. Results: In the early weaning period, average daily feed intake increased when the dietary CP level decreased (linear, p<0.05). During the entire experimental period, average daily gain and the gain to feed ratio decreased when the dietary CP level increased (linear, p<0.01). Additionally, a decrease in dietary CP level resulted in a linear increase in final BW (linear, p<0.05). In the early and late weaning periods, blood urea nitrogen (BUN) decreased when the dietary CP level decreased (linear, p<0.01). There were no significant differences in creatinine, glucose, total protein, triglyceride or insulin-like factor-1 levels over the experimental period. The concentrations of immunoglobulin A (IgA) and IgG were not significantly affected by dietary CP levels during the experimental period. In the early weaning period, fecal and urine N decreased when the dietary CP level decreased (linear, p<0.01). No differences in nutrient digestibility among the treatments during the early weaning period were found. Throughout the whole experimental period, when the dietary CP level decreased in the weaning pig diet, the diarrhea incidence decreased linearly (linear, p<0.01). Throughout the whole experimental period, when the dietary CP level decreased in the weaning pig diet, ammonia, amines and hydrogen sulfide decreased linearly (linear, p<0.01). Conclusion: Reducing dietary CP could decrease diarrhea incidence, the concentration of BUN in serum and odor emission in manure. Furthermore, it could improve N excretion in feces and urine and growth performance in weaning pigs.

• Proceedings of the Korean Society of Plant Pathology Conference
• /
• 2003.10a
• /
• pp.138.2-139
• /
• 2003

Grapevine leafroll-associated 1 virus (GLRaV-1) and Grapevine leafroll-associated 3 virus (GLRaV-3), member of the genus Ampelovirus, are important viral disease of grapevine in the world. these viruses transmitted only dicotyledonous host by vectors such as mealybugs and there is no suitable herbaceous host for virus. The diseased leaves turn yellowish or reddish depending on cultivars and viruses. Viruses are existed at low concentration and ununiformly distribution in grapevine. Using small-scale double-stranded RNA (dsRNA) extraction method, reverse transcription and polymerase chain reaction (RT-PCR) product of 1Kb long which encoded of coat protein (CP) gene for both viruses was successfully amplified with a specific primers. The RT-PCR product was cloned into the plasmid vector and its nucleotide sequences were determined from selected recombinant cDNA clones. Sequence analysis revealed that the CP of GLRaV-1 consisted of 969 nucleotide, which encoded 323 amino acid residues and CP of GLRaV-3 consisted of 942 nucleotide, which encoded 314 amino acid residues. The CP of GLRaV-1 and GLRaV-3 has 93.8％ and 98.7％ amino acid sequence identities, respectively.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.11
• /
• pp.1623-1628
• /
• 2011

The effects of dietary lysine (Lys) at a fixed ratio to crude protein (CP) and essential amino acids (EAA) on early growth response of broilers were studied. Four diets were formulated to contain similar metabolizable energy (ME, 2,950 kcal/kg) but contained graded levels of incremental Lys (1.1, 1.2, 1.3 and 1.4%) while also increasing the dietary CP and EAA (methionine, methionine+ cystine, threonine and tryptophan) to maintain a constant ratio with Lys. Each diet was fed at random to 10 replicates of 6 chicks each throughout the experimental period (1-21 d). At the lowest concentration of Lys of 1.1% (19.04% CP), body weight gain (BWG) was lowest and feed conversion ratio (FCR) was poorest. The BWG increased and FCR decreased linearly as dietary Lys increased upto 1.3% (22.5% CP). Lowest feed consumption was observed in the dietary group that contained 1.1% Lys (19.04% CP) in the diet. Increasing the concentration of Lys to 1.2% (20.77% CP), significantly increased the feed consumption. The concentrations of protein, calcium, phosphorus and cholesterol in serum were not influenced by the variation in Lys contents in the diet. The humoral immune response as measured by antibody titre in response to SRBC inoculation was significantly lower in the diets containing 1.1% Lys compared to 1.4%. It is concluded that the Lys requirement of broilers is 1.3% (22.5% CP) during 0 to 21 days of age for eliciting optimum performance when a fixed ratio of Lys to CP (1:17.31) and essential AA is maintained (1:0.47 Met; 1:0.56 Thr; 1:0.17 Try).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.1
• /
• pp.20-28
• /
• 2011

Crude polysaccharide (CP) was fractionated from the submerged culture (containing both mycelia and culture broth, SC) with Phellinus linteus (PL) in mushroom complete medium (MCM) supplemented with ginseng extract ($65^{\circ}$Bx, GE) to enhance the immune activity. PL-GE-15-CP from SC cultivated in MCM supplemented with GE-15% (v/v, a ratio of MCM volume to GE) showed significantly higher macrophage stimulation (1.45 fold of the saline control at $100{\mu}g$/mL) than PL-GE-5 and 10-CP with GE-5 and 10%, or PL-CP from SC without GE. The potent intestinal immune system modulating activity through Peyer's patch was also obtained by PL-GE-15-CP (1.46 fold). When PL-GE-15-CP further fractionated on DEAE-Sepharose CL-6B (Cl- form), PL-GE-15-CP-II was the significantly higher than others from PL-GE-15-CP or PL-CP on macrophage stimulation, interleukin (IL)-12 production and intestinal immune system modulation (1.54, 3.96 and 1.56 fold, respectively). PL-GE-15-CP-II also had higher anti-metastatic activity against colon 26-M3.1 carcinoma cell (57.3% inhibition of tumor control, $200{\mu}g$/mouse) rather than PL-CP-II. This active fraction (PL-GE-15-CP-II) mainly contained neutral sugar (82.45%) and uronic acid (12.99%), and component sugar analysis showed that PL-GE-15-CP-II consisted mainly of uronic acid, Ara, Man, Gal and Glc (molar ratio of 0.52:0.97:0.63:1.00:0.54). Furthermore, the activity of GE culture was higher compared with culture without GE, indicating that GE helped to enhance the immune activity of P. linteus; also, it is assumed that the polysaccharide plays an important role in immune enhancement.