• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.808-813
• /
• 2004

The stress analysis on orthotropic composite cylindrical shells with one circular or one elliptical cutout subjected to an axial force is carried out by using an analytical and experimental method. The composite cylindrical shell governing equation of the Donnell's type is applied to this study and all results are presented by the stress concentration factor. The stress concentration factor is defined as the ratio of the stress on the region around a cutout to the nominal stress of the shell. The stress concentration factor is classified into the circumferential stress concentration factors and the radial stress concentration factors due to the cylindrical coordinate of which the origin is the center of a cutout. The considered loading condition is only axial tension loading condition. In this study, thus, the maximum stress is induced on perpendicular region against axial direction, on the coordinate. Various cutout sizes are expressed using the radius ratio, (equation omitted), which is the radius of a cutout over one of the cylindrical shell. Experimental results are obtained using strain gages, which are attached around a cutout of the cylindrical shell. As the result from this study, the stress concentration around a cutout can be predicted by using the analytical method for an orthotropic composite cylindrical shell having a circular or an elliptical cutout.

• 대한방사선기술학회지:방사선기술과학
• /
• 제23권1호
• /
• pp.13-19
• /
• 2000

We have presented with the "A study on overexposure rate according to over-density in chest X-ray radiography(I)" last year. In this report, We could calculate the entrance skin dose from chest X-ray film density the formula $I_0=Ix/e^{-{\mu}x}{\times}mG$, (mG is Bucky factor) was used to deliver the skin dose. At that time, There was two problems that the Bucky factor from maker was not equal to field experience and the field size influenced on the Attenuation Rate. The experiment of Bucky factor was done from film method and retried the Attenuation Rate of Acryle phantom according to Good & Poor geometry. As the results, The Bucky factor from maker higher than in this experiments $30{\sim}40%$. The Attenuation Rate in good geometric condition brings about a little alteration compare with poor geometric condition. In the field experiment, we could get the chest image with very low entrance skin radiation dose $29.3{\mu}Sv$, especially with air gap methode, the entrance skin dose was detected $10{\mu}Sv$.

• 한국조리학회지
• /
• 제14권1호
• /
• pp.73-83
• /
• 2008

The purpose of this study was to investigate purchasing variables in the organic food consumption level in Busan. To achieve this purpose, 240 residential women who are organic food consumers were chosen. Among them, 149 women took part in the study. The questionnaire was composed of three parts: 8 demographic characteristics, 9 organic food purchasing conditions, and 22 purchasing variables. The research was continued from August 20th until September 10th, 2007. To derive the results, descriptive analysis, factor analysis, and ANOVA were used by spss 14.0. To sum up the results, three organic food consumption groups were classified into high, middle, and low consumption levels depending on buying condition for organic material. For the factor analysis, 5 factors were named as confidence, quality, safety, appearance, and economy. On the high consumption level, economy factor was highly important than other groups. In general, price would be a more sensitive factor, so they answered the adjusted price range; 52 participants said under 10%, 22 between 11% and 20%, and 17 over 40%.

• 대한조선학회지
• /
• 제11권2호
• /
• pp.1-6
• /
• 1974

The three-dimensional correction factor of the added mass of finite-length elliptic cylinders in vertical vibration in a free surface was calculated. This problem has already been dealt by T. Kumai[5] to contribute to analytical prediction of the three-dimensional correction factor for the added mass in vertical vibration of ships. In Kumai's work, the body boundary condition involved in the appropriate boundary value problem was approximately treated in the course of obtaining the solution. In this work, obtaining the solution derived from mathematically exact treatment of the body boundary condition, the author recalculated the three-dimensional correction factor for length-beam ratio $4{\sim}8$, beam-draught ratio $2.00{\sim}4.50$ and number of nodes from 2 to 7. And the numerical results were compared with both Kumai's results and the author's experimental data for two and three-noded vibrations of the cylinder of beam-draught ratio 2.40 The comparison of the numerical results shows that the author's are always higher than the Kumai's as expected. And the comparison of the numerical results with experimental data shows that the Kumai's numerical results have less deviation in case of two-noded vibration, and that, in case of three-noded vibration, the author's numerical results are in fairly good correspondence.

• 터널과지하공간
• /
• 제30권1호
• /
• pp.63-75
• /
• 2020

터널 발파의 최외곽에서 발생할 수 있는 과대 여굴은 작업자 및 장비의 안전에 저해되며 숏크리트 등 지보량의 증가로 공사 비용이 증가시키는 주요 원인이다. 이러한 여굴은 화약 에너지와 암반의 특성 간의 복잡한 발생 메커니즘으로 인해 완벽한 제어가 매우 어렵다. 본 연구는 여굴 발생의 중요한 원인인 암반의 공학적 특성 중 무지보 막장 상태, 단축압축강도, 풍화도 및 불연속면의 특성(빈도, 상태 및 불연속면과 최외곽선과의 각도) 등과 발생한 여굴의 깊이와의 관계를 feed-forward 인공신경망을 통해 분석하였다. 이를 통해 통해 얻어진 각 인자의 가중치를 기초로 여굴저항도(Overbreak Resistance Factor: ORF)를 개발하였다. 더불어 여굴저항도를 이용한 터널 발파 여굴 관리 시스템을 제안한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.568-571
• /
• 1997

The overall aim of this paper is to determine coupling loss factor using loss factor and structural loss factor. For this purpose, two kinds of loss factor were adopted. One is loss factor of each sub structure, another is structural loss factor based on the complex welded or assembled structure. Using these two parameters, it is possible to derive the coupling loss factor which represent characteristic condition of SEA theory. Coupling loss factor of conjunction in complex structure was expressed as power balance equation. The derived equation for a coupling loss factor has been simplified on the assumption of one directional power flow between two sub structures. Using these conditions, it is possible to find the coupling loss factor equation. The comparison between theory of power transmission on conjunction and above equation, show a good agreement in simple beam structure. To check the effectiveness of above equation, it was adopted rotary compressor. Rotary compressor has three main conjunctions between shell and internal vibration part. This equation was applied to find out the optimum welding point with respect to reduce the noise propagation. It shows the effective tool to evaluate the coupling loss factor in complex structure.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.573-578
• /
• 2000

Recently, Tailor Welded Blanks(TWB) is widely used in automotive industry since the transformation characteristics of its material can be changed. However, clearance between welding surface becomes the important factor which affect the quality of the laser weld, causing difficulties in preparing the sheet. The objective of this paper is to systematically evaluate the effects of previously presented fracture criterion and shearing condition on precise mechanical shearing simulation result. Also predict the optimum shearing condition, effect of shearing condition such as clearance and punch radius on the shear plane shape was evaluated.

• International Journal of Oral Biology
• /
• 제40권1호
• /
• pp.19-25
• /
• 2015

Osteocytes may function as mechanotransducers by regulating local osteoclastogenesis. Reduced availability of oxygen, i.e. hypoxia, could occur during disuse, bone development, and fracture. Receptor activator of nuclear factor-${\kappa}B$ ligand (RANKL) is an osteoblast/stromal cell derived essential factor for osteoclastogenesis. The hypoxia induced osteoclastogenesis via increased RANKL expression in osteoblasts was demonstrated. Hypoxic regulation of gene expression generally involves activation of the hypoxia-inducible factor (HIF) transcription pathway. In the present study, we investigated whether hypoxia regulates RANKL expression in murine osteocytes and HIF-$1{\alpha}$ mediates hypoxia-induced RANKL expression by transactivating RANKL promoter, to elucidate the role of osteocyte in osteoclastogenesis in the context of hypoxic condition. The expression levels of RANKL mRNA and protein, as well as hypoxia inducible factor-$1{\alpha}$ (HIF-$1{\alpha}$) protein, were significantly increased in hypoxic condition in MLO-Y4s. Constitutively active HIF-$1{\alpha}$ alone significantly increased the levels of RANKL expression in MLO-Y4s under normoxic conditions, whereas dominant negative HIF-$1{\alpha}$ blocked hypoxia-induced RANKL expression. To further explore to find if HIF-$1{\alpha}$ directly regulates RANKL transcription, a luciferase reporter assay was conducted. Hypoxia significantly increased RANKL promoter activity, whereas mutations of putative HIF-$1{\alpha}$ binding elements in RANKL promoter prevented this hypoxia-induced RANKL promoter activity in MLO-Y4s. These results suggest that HIF-$1{\alpha}$ mediates hypoxia-induced up-regulation of RANKL expression, and that in osteocytes of mechanically unloaded bone, hypoxia enhances osteoclastogenesis, at least in part, via an increased RANKL expression in osteocytes.

• 한국해안·해양공학회논문집
• /
• 제22권2호
• /
• pp.73-78
• /
• 2010

파에너지는 쇄파되기 이전까지 주로 해저면과의 마찰력에 의하여 감소한다. 파마찰력을 산정하기 위한 연구는 여러 연구자들에 의해 진행되어 왔으며 어느 특정지점에서의 파마찰력 또는 파마찰손실률은 선형파이론으로 주어지는 해저면 입자유속과 연관된 파마찰계수의 도입으로 상당히 정확하게 간단하게 산정할 수 있다. 그러나 장구간에 걸쳐 파마찰력에 의하여 점차적으로 감소되는 파고변이는 상당한 반복 과정을 거쳐야 산정할 수 있었다. 본 연구에서는 기존 경험식을 이용해 전난류, 완난류 경우에 대해 일정경사면에서 천수효과와 마찰손실에 의한 파고 변화를 비교적 간단한 방법으로 추정하는 방법을 제시하였다. 해빈경사가 일정할 때 파고 변이률은 천수계수와 파고 마찰손실계수의 곱으로 간단히 구할 수 있다. 실제 해안과 비슷한 조건의 경우에 대하여 반복시산 과정으로 구한 수치와 간편 산정식으로 간단히 계산한 결과를 비교하여 제시하였다.

• 소성∙가공
• /
• 제3권2호
• /
• pp.215-228
• /
• 1994

The purpose of this paper is to pursue a general method to determine both the flow stress of a material and the friction factor by ring compression test. The materials are assumed to obey the expanded n-power hardening rule including the strain-rate effect. Ring compression is simulated by the rigid-plastic finite element method to obtain the database used in determining the flow stress and friction factor. The Simulation is conducted for various strain hardening exponent, strain-rate sensitivity, friction factor, and compressing speed, as variables. It is assumed that the friction factor is constant during the compression process. To evaluate the compatibility of the database, experiments are carried out at room and evaluated temperature using specimens of aluminum 6061-T6 under dry and grease lubrication condition. It is shown that the proposed test method is useful and easy to use in determining the flow stress and the friction factor.