• Bulletin of the Korean Chemical Society
• /
• 제33권12호
• /
• pp.3935-3936
• /
• 2012

• 한국전자통신학회논문지
• /
• 제15권4호
• /
• pp.665-670
• /
• 2020

CIGS 박막 태양 전지의 버퍼층은 흡수층과 윈도우층 사이의 밴드정렬(band alignment)을 통해 에너지 변환 효율을 향상시킨다. ZnS는 무독성의 II-VI 반도체 화합물로서 직접천이형 광대역 밴드갭과 n형 전도성을 가지며, 높은 광투과성, 높은 굴절률 등의 우수한 전기적, 광학적 특성을 가지고 있고, 우수한 격자정합을 가지는 물질이다. 이 연구에서, RF 마그네트론 스퍼터링 방법에 의해 증착 후 급속 열처리에 의해 제작된 ZnS 버퍼층 박막의 구조적, 광학적 특성의 상관관계에 대해 고찰하였다. (111), (220), (311) 면의 섬아연광 입방정 구조를 확인할 수 있고, 상대적으로 저온에서 급속열처리를 수행한 시료에서는 (002) 면의 우르쯔광 육방정 구조가 함께 나타나는 다결정이 되었다. 고온에서 급속열처리 수행한 시료에서는 섬아연광 입방정 구조의 단결정으로 상전이 된다. 화학적 성분 분석을 통해서 Zn/S의 비율이 화학양론에 근접한 시료에서 섬아연광 입방정 구조의 단결정이 나타났음을 확인하였다 급속열처리 온도가 증가할수록 흡수단이 다소간 단파장 쪽으로 이동되고, 가시광 파장 범위에서 평균 광투과율이 증가하는 경향성을 보이며 500℃ 조건에서는 80.40%로 향상되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.321.2-321.2
• /
• 2013

CdS는 2.42 eV의 밴드 갭을 가지는 직접 천이형 반도체로서 CdTe계와 CGIS계 태양전지의 접합 partner로 많이 이용되어 왔다. 태양전지의 광투과층으로 사용되는 CdS 박막의 필요한 물성으로는 높은 광투과도와 얇은 두께이다. 광투과층으로 사용되는 CdS 막의 광투과도가 높아야 많은 양의 빛이 손실 없이 투과하여 광흡수층인 CIGS에 도달할 수 있다. 특히, CdS막의 두께가 얇으면 밴드 갭 이상의 에너지를 가지는 파장의 빛도 투과시킬 수 있어 태양전지의 효율의 증가을 얻을 수가 있다. 그러나 CdS 막의 두께가 얇을 경우, pinhole이 생성되는 등 막의 균질성이 문제가 되기 때문에 얇으면서도 pinhole이 없는 CdS 박막을 만들기 위한 연구가 진행되고 있다. 본 연구에서는 높은 변환 효율을 갖는 CIGS 박막 태양전지 제작에 적합한 chemical bath depostion(츙)법을 이용하여 CdS 박막을 제조하였다. 또한 반응온도, Cd 및 S source 비, 반응용액의 pH와 같은 증착 조건에 따른 박막의 구조적, 광학적 특성을 조사하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.314.2-314.2
• /
• 2013

CIGS 박막의 물성은 조성에 크게 영향을 받으며, 특히 박막 내 Cu/(In+Ga) 비는 매우 중요한 변수로서 태양전지 특성에 영향을 주게 된다. Cu(In1-xGax)Se2 박막의 전하농도 및 반도체로의 성격을 가장 명확하게 결정하는 조성비는 Cu/(In+Ga) 비이다. 태양전지와 같은 소자로 작용하기 위해서는 Cu/(In+Ga) 비가 1보다 작아야 한다. 고효율의 태양전지는 Cu/(In+Ga)조성이 0.85~0.95로 slightly Cu-poor가 되어야 만들어진다. 본 연구에서는 Cu조성에 따른 CIGS 박막의 구조적, 전기적 특성과 CIGS 태양전지 효율 특성에 관하여 연구하였다. 미세구조 분석결과 Cu 조성이 증가함에 따라 큰 결정립을 가지며 결정립의 성장이 고르게 되어 접합 형성을 좋게 하는 경향을 보였다. X선 회절 분석결과, Cu 함유량 비율이 증가하면서 <112>의 우선배향성에서 <220/204>으로 변화하였다. 그러나, Cu/(In+Ga) 비율이 1이상이 첨가됨에 따라 우선배향은 다시 <112>로 변화함을 알 수 있었다. EDX 분석결과 Ga/(In+Ga) 0.31, Cu/(In+Ga) 0.86의 비율일 때, Carrier density $1.49{\times}1016$ cm-3을 나타내었다. CIGS의 태양전지의 효율 측정결과 Voc=596mV, Jsc=37.84mA/cm2, FF=72.96%로 ${\eta}$=16.47%를 달성하였다.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.107-113
• /
• 2013

In this study, three different types of experimental models of BIPV curtain wall units with GIGS modules were built, and their thermal and electrical performances were analyzed. The experimental results showed that the temperature of the rear side of the GIGS module with the application of an insulation in the curtain wall spandrels was higher than a GIGS module standalone by $22^{\circ}C$, which results in a reduction in the power generation of the former by 8 %. On the other hand, when ventilation was applied to the model to improve the power generation performance, the module temperature was observed to be $142^{\circ}C$ lower compared to the enclosed type, and the power generation performance improved by 5 %. It confirmed that the temperature increase in the rear side of the GIGS module with insulation layer reduced the electrical performance of the module. Based on this, it is claimed that providing sufficient ventilation at the GIGS applied spandrels contribute to improve the power generation of the GIGS module.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권12호
• /
• pp.607-613
• /
• 2001

Molybdenum thin films were deposited on the soda lime glass(SLG) substrates by direct-current planar magnetron sputtering, with a sputtering power density of $4.44W/cm^2$. The working pressure was varied from 0.5 mtorr to 20 mtorr to gain a better understanding of the effect of sputtering pressure on the morphology and microstructure of the Mo film. Thin films of $CU(InGa)Se_2$ (CIGS) were deposited on the Mo-coated glass by three stage co-evaporation process. The highest efficiency device was obtained at the maximum value of the tensive stress. The morphology of Mo-coated films were examined by using scanning electron microscopy The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the residual intrinsic stress were examined by X-ray diffraction.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.318.1-318.1
• /
• 2013

Nowadays Cu2ZnSnS4 (CZTS) solar cell is attracting a lot of attention as a strong alternative to CIGS solar cell due to nontoxic and inexpensive constituent elements of CZTS. From various processes for the fabrication of CZTS solar cell, solution-based deposition of CZTS thin films is well-known non-vacuum process and many researchers are focusing on this method because of large-area deposition, high-throughput, and efficient material usage. Typically the solution-based process consists of two steps, coating of precursor solution and annealing of the precursor thin films. Unlike vacuum-based deposition, precursor solution contains unnecessary elements except Cu, Zn, Sn, and S in order to form high quality precursor thin films, and thus the precise control of precursor thin film preparation is essential for achieving high efficient CZTS solar cells. In this work, we have investigated the effect of preparation condition of CZTS precursor thin films on the performance of CZTS solar cells. The composition of CZTS precursor solution was controlled for obtaining optimized chemical composition of CZTS absorber layers for high-efficiency solar cells. Pre-annealing process of the CZTS precursor thin films was also investigated to confirm the effect of thermal treatment on chemical composition and carbon residues of CZTS absorber layers. The change of the morphology of CZTS precursor thin film by the preparation condition was also observed.

• Current Photovoltaic Research
• /
• 제8권3호
• /
• pp.102-106
• /
• 2020

In this paper, the effect of MoSe₂ on the contact resistance (R_C) of the transparent conducting oxide (TCO) and Mo junction in the scribed P2 region of the Cu(In,Ga)Se₂ (CIGS) solar module was analyzed. The CIGS/Mo junction becomes ohmic-contact by MoSe₂, so the formation of the MoSe₂ layer is essential. However, the CIGS solar module has a TCO/MoSe₂/Mo junction in the P2 region due to structural differences from the cell. The contact resistance (R_C) of the P2 region was calculated using the transmission line method, and MoSe₂ was confirmed to increase R_C of the TCO/Mo junction. B doped ZnO (BZO) was used as TCO, and when BZO/MoSe₂ junction was formed, conduction band offset (CBO) of 0.6 eV was generated due to the difference in their electron affinities. It is expected that this CBO acts as a carrier transport barrier that disturbs the flow of current, resulting in increased R_C. In order to reduce the R_C caused by CBO, MoSe₂ must be made thin in a CIGS solar module.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.398.1-398.1
• /
• 2014

The $Cu_2ZnSnSe_4$ (CZTSe) thin films solar cell is one of the next generation candidates for photovoltaic materials as the absorber of thin film solar cells because it has optimal bandgap (Eg=1.0eV) and high absorption coefficient of $10^4cm^{-1}$ in the visible length region. More importantly, CZTSe consists of abundant and non-toxic elements, so researches on CZTSe thin film solar cells have been increasing significantly in recent years. CZTSe thin film has very similar structure and properties with the CIGS thin film by substituting In with Zn and Ga with Sn. In this study, As-deposited CZTSe thin films have been deposited onto soda lime glass (SLG) substrates at different deposition condition using Pulsed Laser Deposition (PLD) technique without post-annealing process. The effects of deposition conditions (deposition time, deposition temperature) onto the structural, compositional and optical properties of CZTSe thin films have been investigated, without experiencing selenization process. The XRD pattern shows that quaternary CZTSe films with a stannite single phase. The existence of (112), (204), (312), (008), (316) peaks indicates all films grew and crystallized as a stannite-type structure, which is in a good agreement with the diffraction pattern of CZTSe single crystal. All the films were observed to be polycrystalline in nature with a high (112) predominant orientation at $2{\theta}{\sim}26.8^{\circ}$. The carrier concentration, mobility, resistivity and optical band gap of CZTSe thin films depending on the deposition conditions. Average energy band gap of the CZTSe thin films is about 1.3 eV.

• 한국재료학회지
• /
• 제30권4호
• /
• pp.204-210
• /
• 2020

ZnO thin films are of considerable interest because they can be customized by various coating technologies to have high electrical conductivity and high visible light transmittance. Therefore, ZnO thin films can be applied to various optoelectronic device applications such as transparent conducting thin films, solar cells and displays. In this study, ZnO rod and thin films are fabricated using aqueous chemical bath deposition (CBD), which is a low-cost method at low temperatures, and environmentally friendly. To investigate the structural, electrical and optical properties of ZnO for the presence of citrate ion, which can significantly affect crystal form of ZnO, various amounts of the citrate ion are added to the aqueous CBD ZnO reaction bath. As a result, ZnO crystals show a nanorod form without citrate, but a continuous thin film when citrate is above a certain concentration. In addition, as the citrate concentration increases, the electrical conductivity of the ZnO thin films increases, and is almost unchanged above a certain citrate concentration. Cu(In,Ga)Se₂ (CIGS) solar cell substrates are used to evaluate whether aqueous CBD ZnO thin films can be applicable to real devices. The performance of aqueous CBD ZnO thin films shows performance similar to that of a sputter-deposited ZnO:Al thin film as top transparent electrodes of CIGS solar cells.