• 한국분무공학회지
• /
• 제27권3호
• /
• pp.155-160
• /
• 2022

Recently, major developed countries have strengthened automobile fuel efficiency regulations and carbon dioxide emission allowance standards to curb climate change caused by global warming worldwide. Accordingly, research and manufacturing on electric vehicles that do not emit pollutants during actual driving on the road are being conducted. Several automobile companies are producing and testing electric vehicles to commercialize them, but it takes a lot of manpower and time to test and evaluate mass-produced electric vehicles with driving mileage of more than 300km on a per-charge. Therefore, in order to reduce this, a simulation model was developed in this study. This study used vehicle information and MCT speed profile of small electric vehicle as basic data. It was developed by applying Simulink, which models the system in a block diagram method using MATLAB software. Based on the vehicle dynamics, the simulation model consisted of major components of electric vehicles such as motor, battery, wheel/tire, brake, and acceleration. Through the development model, the amount of change in battery SOC and the mileage during driving were calculated. For verification, battery SOC data and vehicle speed data were compared and analyzed using CAN communication during the chassis dynamometer test. In addition, the reliability of the simulation model was confirmed through an analysis of the correlation between the result data and the data acquired through CAN communication.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제16권11호
• /
• pp.3680-3693
• /
• 2022

The handover procedure of IEEE 802.11 wireless local area networks (WLANs) introduces significant delay, which can degrade the quality of service (QoS) especially for delay-sensitive applications. Although studies have been conducted to support handover in SDN-based WLAN, there is no research to reduce the channel scanning procedure that takes up the most delay time in the handover process. The channel scanning procedure is essential to determine the appropriate access point (AP). To mitigate this problem, this paper proposes a SWITCH: SDN-WLAN integrated handover scheme for QoS-Guaranteed mobile service. In SWITCH, each AP periodically broadcasts beacon frames through different channels in a predetermined order that includes the operating channel information of the AP. This allows mobile stations (MSs) to receive the beacon frames of nearby APs, and therefore they can determine the appropriate APs for handover without the channel scanning procedure. By reporting the information of the newly moved AP to the SDN controller, a flow rule is installed in advance to provide fast handover, and packet loss is reduced by buffering data destined for MS. In addition, the proposed scheme can adaptively operate SWITCH to consider the user location and QoS requirement of flow to save radio resource overhead. Performance evaluation results demonstrate that SWITCH can reduce the handover delays, flow table utilization ratio and radio resource overhead while improving the network throughput.

• 전자공학회논문지
• /
• 제51권6호
• /
• pp.124-131
• /
• 2014

본 논문은 무선 개인영역네트워크 환경에서 중계 프로토콜 기능을 가진 시분할다중접속방식(TDMA)의 적응형 기저대역 중계모뎀을 설계한 내용을 기술한다. 설계한 기저대역 중계모뎀은 마스터 동기 신호에 의해 제어되며 최대 14홉의 중계 네트워크를 구성할 수 있다. 효과적인 데이터 중계 통신을 위해 단일포트 메모리에서 우선권을 사용하여 내부 버퍼 설계를 최적화하였다. 그리고 메모리 버스 제어기는 합성된 게이터 수를 최소화시킬 수 방법으로 설계하였다. 협대역 TDMA 중계 통신의 동기 기능을 구현하기 위하여 네트워크 슬롯 동기회로와 프레임 동기회로를 분리하여 게이트수를 줄였다. 이 방법을 사용하여 9만 게이트의 Xilinx FPGA XC6SLX9에서 약 37%(34,000게이트)를 사용하였다. 32비트 싱크워드를 사용한 1024비트 프레임의 통신 수신율은 약 96.4%이다. 설계된 기저대역 중계모뎀을 사용하여 14홉의 중계에서 측정한 최대전송지연시간은 230.4ms이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계합동학술대회 논문집
• /
• pp.21-25
• /
• 2002

Activated sludge processes are widely used in biological wastewater treatment processes. The main motivation of this research is to develop an intelligent control strategy for activated sludge process (ASP). ASP is a complex and nonlinear dynamic system because of the characteristic of wastewater, the change in influent rate, weather conditions, and so on. The mathematical model of ASP also includes uncertainties which are ignored or not considered by process engineer or controller designer. The ASP model based on Matlab/Simulink is designed in this paper. The performance of the model is tested by IWA (International Water Association) and COST (European Cooperation in the filed of Scientific and Technical Research) data that include steady-state results during 14 days. In this paper, fuzzy logic control approach is applied to control the DO (dissolved oxygen) concentration. The fuzzy logic controller that includes two inputs and one output can adjust air flowrate. Also, this paper introduces the remote monitoring and control system that is applied for the CSTR (Continuously Stirred Tank Reactor) wastewater treatment system. The CSTR plant has a local control and the remote monitoring system which is contained communication parts which consist of LAN (Local Area Network) network and CDMA (Code Division Multiple Access) wireless module. Remote control and monitoring systems are constructed in the laboratory.

• Transactions on Control, Automation and Systems Engineering
• /
• 제3권3호
• /
• pp.181-189
• /
• 2001

The software components of embedded control systems get extremely complex as they are designed into distributed systems get extremely complex as they are designed into distributed systems consisting of a large number of inexpensive microcontrollers interconnected by low-bandwidth real-time networks such as the controller area network (CAN). While recently emerging middleware technologies such as CORBA and DCOM address the complexity of distributed programming, they cannot be directly applied to distributed control system design due to their excessive resource demand and inadequate communication models. In this paper, we propose a CORBA-based middleware design for CAN-based distributed embedded control systems. Our design goal is to minimize its resource need and make it support group communication without losing the IDL (interface definition language) level compliance to the OMG standards. To achieve this, we develop a transport protocol on the CAN and a group communication scheme based on the well-known publisher/subscriber model. The protocol effectively realizes subject-based addressing and supports anonymous publisher/subscriber communication. We also customize the method invocation and message passing protocol, referred to as the general inter-ORB protocol (GIOP), of CORBA so that CORBA method invocations are efficiently serviced on a low-bandwidth network such as the CAN. This customization includes packed data encoding and variable-length integer encoding for compact representation of IDL data types. We have implemented our CORBA-based middleware on the mArx real-time operating system we have developed at Seoul National University. Our experiments clearly demonstrate that it is feasible to use CORBA in developing distributed embedded control systems possessing severe resource limitations. Our design clearly demonstrates that it is feasible to use a CORBA-based middleware in developing distributed embedded systems on real-time networks possessing severe resource limitations.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.155-163
• /
• 2003

As vehicles become more intelligent for convenience and safety of drivers, the in-vehicle networking(IVN) systems and smart modules are essential components for intelligent vehicles. However, for wider application of smart modules and IVN's, the following two problems should be overcome. Firstly, because it is very difficult that transducer manufacturers developed the smart module that supports all the existing IVN protocols, the smart module must be independent of the type of networking protocols. Secondly, when the smart module needs to be replaced due to its failure, only the transducer should be replaced these without the replacement of the microprocessor and network transceiver. To solve these problems, this paper investigates the feasibility of an IEEE 1451 based smart module. More specifically, a smart module for DC motor control has been developed. The module has been evaluated for its delay caused by the IEEE 1451 architecture. In addition, the time required for transducer replacement has been measured.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1678-1687
• /
• 2013

This paper describes a prototype of 3-phase 3.3kV/220V 6kVA modular semiconductor transformer developed in the lab for feasibility study. The developed prototype is composed of three single-phase units coupled in Y-connection. Each single-phase unit with a rating of 1.9kV/127V 2kVA consists of a high-voltage high-frequency resonant AC-DC converter, a low-voltage hybrid-switching DC-DC converter, and a low-voltage hybrid-switching DC-AC converter. Also each single-phase unit has two DSP controllers to control converter operation and to acquire monitoring data. Monitoring system was developed based on LabView by using CAN communication link between the DSP controller and PC. Through various experimental analyses it was verified that the prototype operates with proper performance under normal and sag condition. The system efficiency can be improved by adopting optimal design and replacing the IGBT switch with the SiC MOSFET switch. The developed prototype confirms a possibility to build a commercial high-voltage high-power semiconductor transformer by increasing the number of series-connected converter modules in high-voltage side and improving the performance of switching element.

• 한국실내디자인학회논문집
• /
• 제16권4호
• /
• pp.110-118
• /
• 2007

Technology has been viewed at various stages of civilization as leading to future progress. The building, its services systems and management of the work process all contribute to the well-being of people within an organization. Productivity relies on there being a general sense of high morale and satisfaction with the workplace. Now buildings are considered as providing a milieu for human creativity. Flexibility, adaptability, service integration and high standards of finishes offer an intelligence threshold. Building Automation System(BAS) - controlled lighting systems may offer incremental energy saving. Conventional Lighting control systems often control equipment in a single room or over the limited area, because they are centralized control systems, which means that all the controlled circuits must be wired to a single control panel. The computers used by these systems are typically dedicated microprocess that perform only lighting control functions. By comparison, modern Building automation systems are distributed control system, which means that their computing hardware and software are distributed as a network that microprocessor-based control modules and standard PC. PLC(Programmable Logic controller) is extensible virtually without limits, so that all the lighting in a facility can be controlled by single, unified system - the same system that also can control and monitor the building's HVAC, security, and manufacturing processed, elevators, and more. A Building automation system can control light using schedules, manual controls, occupancy sensors, and photosensors, either singly or in combination. Building Lighting control and monitoring system will be for a energy saving and efficient building management system.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2006년도 학술대회
• /
• pp.261-264
• /
• 2006

지능형 차량정보 시스템은 21세기 교통체계로 기대를 모으고 있는 ITS(Intellligent Transport System)의 구축에 핵심이 되는 시스템이다. 이러한 시스템을 구현하기 위해서 종래의 네비게이션, 차량용 무선통신, 차량진단 등의 단일화된 시스템을 통합적으로 수행하며, 계측 또는 수집된 데이터를 분석하여 지능적으로 차량의 주행 상태를 분석 / 진단함으로써 차량에서의 안전한 운행과 운전자 및 승객들이 요구하는 정보 또는 다양한 서비스를 제공하기 위한 새로운 모듈의 개발이 절실히 필요한 실정이다. 따라서, 본 논문에서는 CAN(Controller Area Network) BUS을 이용한 차량의 상태수집 모듈과 능동 데이터베이스에 관해 기술하고 이를 통합하기 위한 임베디드 보드를 이용한 CAN BUS연계형 차량용 복합통신모듈의 프로토타입 H/W을 구성하여 실용화 가능성 및 유용성을 제시하고자 하였다.

• 정보보호학회지
• /
• 제32권4호
• /
• pp.7-17
• /
• 2022

운전자 보조 시스템을 통한 차량의 전자적인 제어를 위하여, 최근 차량에 탑재된 전자 제어 장치 (ECU; Electronic Control Unit)의 개수가 급증하고 있다. ECU는 효율적인 통신을 위해서 차량용 내부 네트워크인 CAN(Controller Area Network)을 이용한다. 하지만 CAN은 기밀성, 무결성, 접근 제어, 인증과 같은 보안 메커니즘이 고려되지 않은 상태로 설계되었기 때문에, 공격자가 네트워크에 쉽게 접근하여 메시지를 도청하거나 주입할 수 있다. 악의적인 메시지 주입은 차량 운전자 및 동승자의 안전에 심각한 피해를 안길 수 있기에, 최근에는 주입된 메시지를 식별하기 위한 침입 탐지 시스템(IDS; Intrusion Detection System)에 대한 연구가 발전해왔다. 특히 최근에는 AI(Artificial Intelligence) 기술을 이용한 IDS가 다수 제안되었다. 그러나 제안되는 기법들은 특정 공격 데이터셋에 한하여 평가되며, 각 기법에 대한 탐지 성능이 공정하게 평가되었는지를 확인하기 위한 평가 프레임워크가 부족한 상황이다. 따라서 본 논문에서는 machine learning/deep learning에 기반하여 제안된 차랑용 IDS 5가지를 선정하고, 기존에 공개된 데이터셋을 이용하여 제안된 기법들에 대한 비교 및 평가를 진행한다. 공격 데이터셋에는 CAN의 대표적인 4가지 공격 유형이 포함되어 있으며, 추가적으로 본 논문에서는 메시지 주기 유형을 활용한 공격 유형을 제안하고 해당 공격에 대한 탐지 성능을 평가한다.