• Structural Engineering and Mechanics
• /
• v.36 no.2
• /
• pp.197-206
• /
• 2010

The purpose of this paper is to carry out both experimental and theoretical investigations of R.C. short column subjected to horizontal forces under constant compressive loading. Eight specimens with section of 40 cm ${\times}$ 40 cm, height 40 cm and 50 cm and different type hoop were used of the steel cage to detect the seismic behavior of reinforced concrete short columns. Hoop spacing of column, strength of concrete, and the axial load of experiments were the three main parameters in this test. A series of equations were derived to reveal the theory could be used on analysis short column, too. Through test failure model of R.C short column being established, the type of hoop affects the behavior R.C short column in ductility rather than in strength. And the effect of analysis by Truss Model is evident and reliable in shear failure model of short column.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.100-109
• /
• 2001

The backscattered sound energy by fish depends on size and physical structure and, most important, on the presence or absence of a swimbladder. Target strength experiments of red seabream (Pagrus major) were conducted by using 38 (split-beam), 120 (split-beam) and 200 kHz (dual-beam) frequencies with live fishes confined in a net-cage and free swimming in tank without the cage, respectively. For 38, 120, and 200 kHz frequencies, target strength equations are expressed as a function of fish length：TS/sub 38kHz/=20 log/sub 1o(l)/-66.41, TS/sub 120kHz/＝20 log/sub 1o(1)/-71.80, and TS/sub 200kHz/＝20 log/sub 1o(1)/-73.94. To test the acoustic models by using Helmholtz-Kirchhoff ray approximation, predictions of target strength based on swimbladder morphometries are compared with target strength measurements. The target strength of whole fish depends on variations in swimbladder morphology than fish body morphology. In the mean time, when the fish is confined in the net cage, scattering length by the backscattered signal matched with the Gaussian PDF, while under the free-swimming condition, scattering length is close to the Rayleigh PDF.

• Journal of the Korean Society of Safety
• /
• v.36 no.1
• /
• pp.9-17
• /
• 2021

This study analyses the load imbalance of the tower crane used in telescoping work for structural safety, owing to the difference in wind speed and balance weight position. This is because wind speed and position of the balance weight have a significant impact on the structural stresses of a tower crane during telescoping work. Therefore, structural analysis was performed on the 290HC model, which is often used at construction sites and has only one cylinder installed. Moreover, two models were classified to determine the load acting on the connecting part of the telescopic cage to slewing platform and the cylinder. Five types of balance weight positions were applied at regular intervals from jibs; moreover, four types of wind load criteria were differently applied. Hence, the telescopic cage columns were destroyed at all balance weight positions at a wind speed of 30 m/s and only at certain locations at a wind speed of 20 m/s. Furthermore, failures occurred for cylinders, torsional, and bending at wind speeds of 30 m/s and 20 m/s, load imbalances above the allowable thresholds considering the safety factor. In addition, the load imbalance in the telescoping work also varied depending on the position of the balance weights. The results of these studies have validated that the current standards of adjusting the appropriate position of the balance weights on the jib are completely valid, with the telescoping work to be executed only at wind speeds of less than equal to 10 m/s.

• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.27-28
• /
• 2006

This paper deals with an approach to the reduction of potential rise according to the buried depth of structure. In order to analyze the surface potential rise of structure, an electrolytic tank which simulates the semi-infinite earth has been used. The potential rise has been measured and analyzed for types of structure using an electrolytic tank experimental apparatus in real time. The structure models were designed through reducing real buildings and fabricated with two types on a scale of one-one hundred sixty When a test current flowed through structure models, the potential rise of outline frame type(structure model A) was more high than that of electric cage type(structure model B). The distributions of surface potential rise are dependent on the buried depth of structure model.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.805-807
• /
• 2002

In this paper, a method for an accurate and fast transient analysis, which employs a single slot model for the rotor, is presented. The equivalent circuit parameters are extracted from a combined method of F. E. M and equivalent circuit on 1 slot rotor boundary condition. Two kinds of circuit parameters for each slip are applied to equivalent circuit controlled by variable-voltage variable- frequency. One is the constant parameters at rated speed, and the other is the parameters varying in accordance with slip-frequency. The computer characteristics of the suggested method for four-pole 1.5KW induction motor are compared with those of Equivalent circuit for the transient analysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.916-923
• /
• 2014

This paper proposes a low-cost switched-mode rectifier (SMR) for a small-scale wind turbine with a permanent magnet synchronous generator (PMSG) system. Also, a sensorless Fuzzy MPPT control is realized by the proposed system. In the PMSG system with the SMR, the synchronous impedance can be replaced as the input inductor of a boost converter. Moreover, the sensorless MPPT control using the Fuzzy technique is carried out by the duty-ratio regulation of the SMR. The relation between the generating power and the duty-ratio is ruled by the chain rule. The wind turbine model is implemented by the squirrel cage induction motor and generated the variable torque when the generator speed is varied. To verify the performance of the proposed system, simulation and experimental results are executed.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.718-723
• /
• 2007

A three dimensional multibody modeling of a launcher system was developed and dynamic characteristics of the system was carried out. All the components were modeled as rigid bodies, All the components of system, ie; chassis, turret, cage and suspension parts, are modeled as rigid. The force interaction between the ground and tire was modeled as a point contact model. The factors were selected as cause and effect diagram of the MINITAB. To see effect of the stiffness, damping, mass at the launcher system, several cases of suspension parameters were compared and optimal values were selected. The stiffness and the damping coefficient were selected as design variables to minimize the required time for the next fire. The dynamic simulation was carried out using the ADAMS, and the MINITAB was employed for data analysis.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.28-30
• /
• 1989

This paper is analyzed the electrical characteristics of the round solid rotor of turbo-generator without damper cage influence the induction generation modes and the torsional interaction modes of the SSR phenomena, and then examines the problem of representing electrical characteristics which is dependent on frequency and different wedge materials. The basic model of turbo-generator used in the field analysis is viewed as 5-regions of different permeability and conductivity characteristics. The analytical method, which is used in this paper is based on solving a boundary value problem involving 3-D fields, and the basic function consists of the 2-D Fourier series.

• The Journal of Fisheries Business Administration
• /
• v.43 no.2
• /
• pp.67-77
• /
• 2012

Based on the survey on aquaculture management status in Nohwa-eup, Bogil-myeon, Wando-eup in Wando region, this study aimed to estimate productive efficiencies of abalone aquaculture production using a stochastic frontier approach (SFA) and to find out their determinants. In the analysis, a Cobb-Douglas production function with an inefficiency term that follows an halfnormal distribution was assumed for the estimation of productive efficiencies. Then, based on the outcomes of productive efficiencies, determinants of productive efficiency were investigated using a tobit regression model. Results showed that the average inefficiency was estimated to be 10% and the production size would be a statistically significant variable for the production. In addition, it was shown that the cage installing method would be an important factor affecting to the level of productive efficiency.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.742-747
• /
• 1998

In the High-Speed range for salient type synchronous reluctance motors, the effect of iron loss can not be negligible. In this paper, the SynRM without cage is analyzed mathematically to model and the speed control system is examined by simulation. In order to control the revolution speed, a closed-loop control with vector control and decoupling control are applied to the high-speed SynRM drives. The speed control system is analyzed to investigate the desired speed characteristics of high SynRM by simulation.