• 한국농림기상학회지
• /
• 제1권1호
• /
• pp.29-35
• /
• 1999

본 연구는 경기도 광주지역의 낙엽송 임분에 인공 강우기를 설치하여 수리특성과 관련한 공간 변이와 상관관계를 구명하기 위하여 수행되었다. 수분유속과 보유능은 원래 토성, 구조와 유기물을 근거로 지표면에서 인공가우기로 수분을 일정속도로 가하면서 측정하였다. 이 방법은 간단히 유기물을 제거하거나 기존의 상태에서 수평한 지표면에 3가지의 강우 강도에서 실시하였으며 한편 경계면은 안정하며 포화상태의 습윤 토양에서 투수계수와 매트릭 유속기능을 조사하였다. 투수계수는 $_1$( $Z_{c}$) = $_2$( $Z_{c}$) = $_{c}$ 이라는 지속적 유속 조건하에서 $K_{i+}$$_1$ $_{c}$= $K_{i}$( $_{c}$) [1-d /dz]의 공식을 적용하였다. 본 연구 결과 토양내에서 유속에 영향을 미치는 공극 특성과 유기물 함량이 광범위하게 수분 보유능과 포화투수계수의 공간 변이에 영향을 미치는 것으로 조사되었다.것으로 조사되었다.되었다.

• Journal of Mechanical Science and Technology
• /
• 제15권8호
• /
• pp.1156-1164
• /
• 2001

Evaporation heat transfer coefficients and pressure drops were measured for smooth and micro-fin tubes with R-22 and R-410A. Heat transfer measurements were performed for 3.0m long horizontal tubes with nominal outside diameters of 9.52 and 7.0mm over an evaporating temperature range of -15 to 5$\^{C}$, a mass flux range of 68 to 211kg/㎡s, and a heat flux range of 5 to 15kW/㎡. It was observed that the heat transfer coefficient increased with mass flux. Evaporation heat transfer coefficients of R-22 and R-410A increased as the evaporating temperature dropped at a lower heat flux. Generally, R-420A showed the higher heat transfer coefficients than R-22 in the range of low mass flux, high heat flux and high evaporating temperature. Pressure drop increased with a decrease of evaporating temperature and a rise of mass flux. Pressure drop of R-22 was higher than that of R-410A at the same mass flux.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.260-262
• /
• 1998

A new method of induction motor drive, which requires not shaft encoder, is presented. This system has both torque and speed controls that are performed by vector control. The scheme is on the basis of a rotor flux speed control, which is performed by torque producing current and rotor flux, derived from the stator voltages and currents. But, there is a problem with respect to the calculated rotor flux vector, which is an integrating operation by which the rotor induced voltage is converted into the rotor flux. The calculated rotor flux does not work so that it is unstable in initial operation, as motor speed approaches zero. For the proposed rotor flux estimator, a lag circuit is employed, to which both the motor-induced voltage and rotor flux command are imposed, and it is possible to calculate even a low frequency down to standstill. We show the validity of the proposed control method through several computer simulations.

• Journal of Magnetics
• /
• 제21권2호
• /
• pp.239-243
• /
• 2016

High temperature superconductor (HTS) magnet systems usually employ metal current leads which bridge between the cryogenic environment and room temperature. Such current leads are the dominant heat load for these magnet systems due to a combination of electrical resistance and heat conduction. HTS flux pumps enable large currents to be injected into a HTS magnet circuit without this heat load. We present results from an axial-type HTS mechanically rotating flux pump which employs a ferromagnetic circuit and a Cu-stabilized coated conductor (CC) HTS stator. We show the device can be described by a simple circuit model which was previously used to describe barrel-type flux pumps, where the model comprises an internal resistance due to dynamic resistance and a DC voltage source. Unlike previously reported devices, we show the internal resistance and DC voltage in the flux pump are not exactly proportional to frequency, and we ascribe this to the presence of eddy currents. We also show that this axial-type flux pump has superior current injection capability over barrel-type flux pumps which do not incorporate a magnetic circuit.

• Journal of Pharmaceutical Investigation
• /
• 제34권4호
• /
• pp.275-281
• /
• 2004

We have studied the effect of polarity, current density, current duration, crosslinking density, swelling ratio, and permeation enhancers on the transdermal flux of ketoprofen from acrylamide hydrogel. Hydrogel was prepared by free radical crosslinking polymerization of acrylamide. Drug loading was made just before transport experiment by soaking the hydrogel in solution containing drug. In vitro flux study using hairless mouse skin was performed at $36.5^{\circ}C$ using side-by-side diffusion cell, and the drug was analysed using HPLC/UV system. The result showed that, compared to passive flux, the total amount of drug transported increased about 18 folds by the application of $0.4\;mA/cm^2$ cathodal current. Anodal delivery with same current density also increased the total amount of drug transported about 13 folds. It seemed that the increase in flux was due to the electrorepulsion and the increase in passive permeability of the skin by the current application. Flux increased as current density, the duration of current application and loading amount (swelling duration) increased. As the cross linking density of the hydrogel increased, flux clearly decreased. The effect of hydrophilic enhancers (urea, N-methyl pyrrolidone, Tween 20) and some hydrophobic enhancers (propylene glycol monolaurate and isopropyl myristate) was minimal. However, about 3 folds increase in flux was observed when 5% oleic acid was used. Overall, these results provide some useful information on the design of an optimized iontophoretic delivery system of ketoprofen.

• 한국대기환경학회지
• /
• 제20권6호
• /
• pp.749-758
• /
• 2004

Nitrous oxide ($N_2$O) has been known as an important trace gas due to the greenhouse gas and the major source of stratospheric oxide of nitrogen (NO). Soil is the major source of $N_2$O in nature. The physicochemical characteristics of soils affect the emission of $N_2$O from soil. These physicochemical parameters are soil moisture, soil temperature, and soil N content. Since these parameters are correlated to the flux of $N_2$O from soil individually and compositely, there still remain many unknowns in the mechanism to produce $N_2$O in soil and the roles of such physicochemical parameters which affect the soil $N_2$O emission. Soil $N_2$O fluxes were measured at different levels in water filled pore space (WFPS), soil temperature and soil N contents from the same amounts of soils which were sampled from agriculturally managed upland field in a depth of ～30 cm at Kunsan. The soil $N_2$O flux measurements were conducted in a laboratory with a closed flux chamber system. The optimum soil moisture and soil temperature were observed at 60% of WFPS and ～13$^{\circ}C$. The soil $N_2$O flux increased as soil N contents increases during the whole experimental hours (up to 48 hours). However, average $N_2$O flux decreased after ～30 hours when organic carbon was mixed with nitrogen in the sample soils. It is suggested that organic carbon could be important for the emission of $N_2$O, and that the ratio of N to C needs to be identified in the process of $N_2$O soil emission.

• 한국자기학회지
• /
• 제11권3호
• /
• pp.134-140
• /
• 2001

Flux-gate마그네토미터는 1930년대에 개발되어 오늘날까지 저자장측정장치로 널리 사용되고 있다. 본 연구에서는 비정질 코아를 사용하여 분해능이 우수하고 소비 전력이 적으면서 장기적 신뢰성이 우수한 Hux-gate마그네토미터를 개발하기 위하여, 교류자기 특성이 우수한 Allied Chem.사의 2714A의 열처리에 의한 센서코아의 자기적 특성변화를 측정하였다. As quenched상태로 사용한 센서코아는 센서의 noise정도가 높고 시간과 온도에 따라서 교류자기특성이 변화하였으나, 350 $^{\circ}C$에서 1시간 열처리한 시편의 경우, 센서의 noise 정도는 as quenched 상태보다 10배 정도 향상되었으며, 주파수 DC~10 Hz 범위에서 0.1 nT 정도의 noise를 보였다. 자기적특성 또한 매우 안정적인 특성을 보였으며, 시간이 경과함에 따라 최대자화력, 각형비, 보자력등이 지수함수적으로 포화치에 접근하는 경향을 보였다. 따라서 센서 설계시 이들 특성의 변화를 고려할 경우 장기적으로 매우 안정된 flux-gate마그네토미터의 개발이 가능함을 알 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제22권3호
• /
• pp.31-37
• /
• 2002

This experimental study represents the results of an analysis on the characteristics of flux density distributions in the focal region of solar concentrator. The characteristics of flux density distributions are investigated to optimally design and position a cavity receiver. This deemed very useful to find and correct various errors associated with a dish concentrator. We estimated the flux density distribution on the target placed along with focal lengths from the dish vertex to experimentally determine the focal length. It is observed that the actual focal point exists when the focal length is 2.17 m. We also evaluated the position of flux centroid, and it was found that there were errors within 2 cm from the target center. The total integrated power of 2467 W was measured under focal flux distributions, which corresponds to the intercept rate of 85.8%. As a result of the percent power within radius, approximately 90% of the incident radiation is intercepted by about 0.06 m radius.

• 한국해양공학회지
• /
• 제22권1호
• /
• pp.13-21
• /
• 2008

In this study a method to predict CHF(Critical heat flux) in vertical round tubes with axially non-uniform cosine heat flux distribution for water was examined. For this purpose a local condition hypothesis based CHF prediction correlation for uniform heat flux in vertical round tubes for water was developed from 9,366 CHF data points. The local correlation consisted of 4 local condition variables: the system pressure(P), tube diameter(D), mass flux of water(G), and 'true mass quality' of vapor($X_t$). The CHF data points used were collected from 13 different published sources having the following operation ranges: 1.01 ${\leq}$ P (pressure) ${\leq}$ 206.79 bar, 9.92${\leq}$ G (mass flux) ${\leq}$ 18,619.39 $kg/m^2s$, 0.00102 ${\leq}$ D(diameter) ${\leq}$ 0.04468 m, 0.0254${\leq}$ L (length) ${\leq}$ 4.966 m, 0.11 ${\leq}$ qc (CHF) ${\leq}$ 21.41 $MVW/m^2$, and -0.87 ${\leq}X_c$ (exit qualities) ${\leq}$ 1.58. The result of this work showed that a uniform CHF correlation can be easily extended to predict CHF in axially non-uniform heat flux heater. In addition, the location of the CHF in axially non-uniform tube can also be determined. The local uniform correlation predicted CHF in tubes with axially cosine heat flux profile within the root mean square error of 12.42% and average error of 1.06% for 297 CHF data points collected from 5 different published sources.

• 한국산림과학회지
• /
• 제110권4호
• /
• pp.554-568
• /
• 2021

산림은 육상생태계에서 가장 큰 탄소흡수원으로 기후변화 대응에 있어 산림의 대기 중 이산화탄소 농도 저감 역할은 중요하다. 최근 '2050 탄소중립 계획'에 산림의 탄소흡수 기능의 강화가 기본 방향으로 제시되면서 정확한 산림의 탄소흡수량 산정이 강조되고 있다. 산림부문의 탄소흡수량은 Intergovernmental Panel on Climate Change 지침을 따라 산림 내 생물량, 고사목, 임상 유기물층, 토양층, 수확된 목재제품 등 여러 탄소 저장고 내 탄소축적 변화량으로부터 산정한다. 그러나 국내 산림의 경우 하층 식생을 제외한 주요 수종의 임목 재적 증가로부터 추정한 생물량 증가량만을 산림의 탄소흡수량으로 산정하고 있어 실제 산림의 탄소흡수량과 큰 차이가 발생할 수 있다. 이에 본 연구에서는 경기도 광주시 태화산에 위치한 57년생 잣나무 조림지에서 에디 공분산 시스템과 자동화 토양챔버 시스템을 이용한 탄소 플럭스 관측을 통해 산림의 탄소 교환량 및 순 탄소흡수량을 정량화하고, 이를 현재 산림의 탄소흡수량 산정 방법에 따라 법정림 임분수확표 내 연평균 생장량과 국가 고유계수를 이용하여 계산한 잣나무 조림지 임목의 생물량 증가량과 비교하였다. 또한 탄소 플럭스 관측기반의 순 탄소흡수량과 잣나무 조림지의 생물량 증가량 및 임상 유기물층의 탄소저장 변화량 등의 차이로부터 나머지 탄소 저장고에서 연간 탄소저장 변화량을 추정하였다. 그 결과 탄소 플럭스로부터 계산한 잣나무 조림지의 연간 순 탄소흡수량은 5.96 MgC ha^-1으로 생물량 증가로부터 계산한 임목의 연간 탄소흡수량 2.77 MgC ha^-1보다 약 2.2배 많았다. 연간 임상 유기물층의 탄소저장 변화량은 0.75 MgC ha^-1로 추정되어, 연간 하층 식생, 고사목, 토양층 등의 탄소 저장고로 유입되는 탄소의 양이 2.45 MgC ha^-1으로 추정되었다. 본 연구의 결과는 국내 산림이 현재 평가 수준보다 더 큰 탄소흡수원임을 보여주며, 탄소 플럭스 관측과 더불어 하층 식생, 고사목, 토양층 등의 탄소 저장고에서 탄소축적 변화량의 정량화를 통해 더욱 정확한 산림부문 탄소흡수량 산정이 필요함을 시사한다.