• Korean Journal of Materials Research
• /
• v.18 no.6
• /
• pp.326-333
• /
• 2008

Since the 1990s, the second generation of Zirconium alloys containing main alloy compositions of Nb, Sn and Fe have been used as a replacement of Zircaloy-4 (Zr-Sn-Fe-Cr), a first-generation Zirconium alloy, to meet severe and rigorous reactor operating conditions characterized by high-burn-up, high-power and high-pH operations. In this study, the mechanical properties and creep behaviors of Zr-Sn-Fe-Cr and Zr-Nb-Sn-Fe alloys were investigated in a temperature range of $450{\sim}500^{\circ}C$ and in a stress range of $80{\sim}150\;MPa$. The mechanical testing results indicate that the yield and tensile strengths of the Zr-Nb-Sn-Fe alloy are slightly higher compared to those of Zr-Sn-Fe-Cr. This can be explained by the second phase strengthening of the $\beta$-Nb precipitates. The creep test results indicate that the stress exponent for the steady-state creep rate decreases with the increase in the applied stress. However, the stress exponent of the Zr-Sn-Fe-Cr alloy is lower than that of the Zr-Nb-Sn-Fe alloy in a relatively high stress range, whereas the creep activation energy of the former is slightly higher than that of the latter. This can be explained by the dynamic deformation aging effect caused by the interaction of dislocations with Sn substitutional atoms. A higher Sn content leads to a lower stress exponent value and higher creep activation energy.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.1038-1042
• /
• 2008

Mono and multilayer TiO2(Fe, $PEG_{600}$) films were deposited by the dip-coating on $SiO_2$/glass substrate using sol-gel method. In an attempt to improve the antibacterial properties of doped $TiO_2$ films, the influence of the iron oxides and polyethilenglycol ($PEG_{600}$) on the morphological, optical, surface chemical composition and biological properties of nanostructured layers was studied. Complementary measurements were performed including Spectroscopic Ellipsometry (SE), Scanning Electron Microscopy (SEM) coupled with the fractal analysis, X-Ray Photoelectron Spectroscopy (XPS) and antibacterial tests. It was found that different concentrations of Fe and $PEG_{600}$ added to coating solution strongly influence the porosity and morphology at nanometric scale related to fractal behaviour and the elemental and chemical states of the surfaces as well. The thermal treatment under oxidative atmosphere leads to films densification and oxides phase stabilization. The antibacterial activity of coatings against Escherichia Coli bacteria was examined by specific antibacterial tests.

• Journal of Sensor Science and Technology
• /
• v.24 no.6
• /
• pp.364-367
• /
• 2015

Tin oxide thin films were fabricated on glass substrates by the successive ionic layer adsorption and reaction (SILAR) method at room temperature and ambient pressure. Before measuring their properties, all samples were annealed at $500^{\circ}C$ for 2 h in air. Film thickness increased with the number of cycles; X-ray diffraction patterns for the annealed $SnO_2$ thin films indicated a $SnO_2$ single phase. Thickness of the $SnO_2$ films increased from 12 to 50 nm as the number of cycles increased from 20 to 60. Although the optical transmittance decreased with thickness, 50 nm $SnO_2$ thin films exhibited a high value of more than 85%. Regarding electronic properties, sheet resistance of the films decreased as thickness increased; however, the measured resistivity of the thin film was nearly constant with thickness ($3{\times}10^{-4}ohm/cm$). From Hall measurements, the 50 nm thickness $SnO_2$ thin film had the highest mobility of the samples ($8.6cm^2/(V{\cdot}s)$). In conclusion, optical and electronic properties of $SnO_2$ thin films could be controlled by adjusting the number of SILAR cycles.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.437-444
• /
• 2005

Unburned hydrocarbon (UBHC) emissions from gasoline engines remain a primary engineering research and development concern due to stricter emission regulations. Gasoline engines produce more UBHC emissions during cold start and warm-up than during any other stage of operation, because of insufficient fuel-air mixing, particularly in view of the additional fuel enrichment used for early starting. Impingement of fuel droplets on the cylinder wall is a major source of UBHC and a concern for oil dilution. This paper describes an experimental study that was carried out to investigate the distribution and 'footprint' of fuel droplets impinging on the cylinder wall during the intake stroke under engine starting conditions. Injectors having different targeting and atomization characteristics were used in a 4-Valve engine with optical access to the intake port and combustion chamber. The spray and targeting performance were characterized using high-speed visualization and Phase Doppler Interferometry techniques. The fuel droplets impinging on the port, cylinder wall and piston top were characterized using a color imaging technique during simulated engine start-up from room temperature. Highly absorbent filter paper was placed around the circumference of the cylinder liner and on the piston top to collect fuel droplets during the intake strokes. A small amount of colored dye, which dissolves completely in gasoline, was used as the tracer. Color density on the paper, which is correlated with the amount of fuel deposited and its distribution on the cylinder wall, was measured using image analysis. The results show that by comparing the locations of the wetted footprints and their color intensities, the influence of fuel injection and engine conditions can be qualitatively and quantitatively examined. Fast FID measurements of UBHC were also performed on the engine for correlation to the mixture formation results.

• Advances in materials Research
• /
• v.2 no.2
• /
• pp.77-91
• /
• 2013

High quality nanoparticles of neodymium barium niobium ($NdBa_2NbO_6$) perovskites have been synthesized using an auto ignition combustion technique for the first time. The nanoparticles thus obtained have been characterized by powder X-ray diffraction, thermo gravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy, Raman spectroscopy and transmission electron microscopy. UV-Visible absorption and photoluminescence spectra of the samples are also recorded. The structural analysis shows that the nano powder is phase pure with the average particle size of 35 nm. The band gap determined for $NdBa_2NbO_6$ is 3.9 eV which corresponds to UV-radiation for optical inter band transition with a wavelength of 370nm. The nanopowder could be sintered to 96% of the theoretical density at $1325^{\circ}C$ for 2h. The ultrafine cuboidal nature of nanopowders with fewer degree of agglomeration improved the sinterability for compactness at relatively lower temperature and time. During the sintering process the wide band gap semiconducting behavior diminishes and the material turns to a high permittivity dielectric. The microstructure of the sintered surface was examined using scanning electron microscopy. The striking value of dielectric constant ${\varepsilon}_r=43$, loss factor tan ${\delta}=1.97{\times}10^{-4}$ and the observed band gap value make it suitable for many dielectric devices.

• Journal of the Korean Magnetics Society
• /
• v.7 no.5
• /
• pp.237-242
• /
• 1997

The microstructure and soft magnetic properties of as-deposited Fe-Hf-O thin film alloys, which are produced at $P_{O2}=10%$ by rf magnetron sputtering method in $Ar+O_2$ mixed gas atmosphere, is investigated. Newly developed $Fe_{82}Hf_{3.4}O_{14.6}$ film exhibits good soft magnetic properties with $4{\pi}M_s=17.7$ kG, $H_c=0.7$ Oe and ${\mu}_{eff}$(0.5~100MHz)=2,500, respectively. The Fe-Hf-O films are composed of $\alpha$-Fe nanograins and amorphous phase with larger amounts of Hf and O elements which chemically combine each other. With increasing Hf area fraction, Hf and O contents increased proportionally. It was considered that O content in films was determined by Hf contents, because O was chemically combined with Hf. It results from decreasing the $\alpha$-Fe grain size by precipitates (Hf and O), high electrical resistivity. The $Fe_{82}Hf_{3.4}O_{14.6}$ film exhibits the quality factor (Q=$\mu$'/$\mu$") of 25 at 20 MHz. These good frequency characteristics are considered to be superior to other films already reported.o other films already reported.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.124-131
• /
• 2006

For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.

• Applied Chemistry for Engineering
• /
• v.5 no.2
• /
• pp.327-336
• /
• 1994

The synergistic effects in mechanical mixture catalysts of Mo-V-O and metal oxide were investigated for the selective oxidation of acrolein. The metal oxides used are $SnO_2$, ${\alpha}-Sb_2O_4$, $WO_3$, ${\alpha}-Al_2O_3$, CuO, $MnO_2$, $Cu_2O$, MgO, CoO, and ZnO. Mechanical mixtures of Mo-V-O plus $SnO_2$ or ${\alpha}-Sb_2O_4$ had resulted in higher conversion of acrolein and higher yield of acrylic acid than Mo-V-O. The origin of the synergy is attributed to the cooperation of Mo-V-O and $SnO_2$ or ${\alpha}-Sb_2O_4$, in which $SnO_2$ or ${\alpha}-Sb_2O_4$ forms dissociated oxygens at their oxygen vacancies and transports them to Mo-V-O. $Cu_2O$, MgO, CuO, and $MnO_2$, increased conversion of acrolein but decreased yield of acrylic acid. CoO and ZnO inhibited the catalytic performance of Mo-V-O. The different role of these metal oxides is explained in terms of their oxidation-reduction properties.

• The Korean Journal of Physiology
• /
• v.20 no.2
• /
• pp.257-270
• /
• 1986

It has been reported that the luteal function may be regulated by the intracellular calcium in luteal cells (Higuchi et al, 1976; Dorflinger et at, 1984; Gore and Behrman, 1984) which is adjusted partially by $Ca^{++}-ATPase$ activities in luteal cell membranes (Verma and Pennistion, 1981). However, the physicochemical and kinetic properties of $Ca^{++}-ATPase$ in luteal membranes were not fully characterized. This study was, therefore, undertaken to partially characterize the physicochemical and kinetic properties of $Ca^{++}-ATPase$ system in luteal membranes and microsomal fractions, known as an one of the major $Ca^{++}$ storge sites (Moore and Pastan, 1978), from the highly luteinized ovary Highly luteinized ovaries were obtained from PMSG-hCG injected immautre female rats. Light membrane and heavy membrane fractions and microsomal fractions were prepared by the differential and discontinuous sucrose density gradient centrifugation method desribed by Bramley and Ryan (1980). Light membrane and heavy membrane fractions and microsomal fractions from highly luteinized ovaries are composed of the two different kinds of $Ca^{++}-ATPase$ system. One is the high affinity $Ca^{++}-ATPase$ which is activated in low $Ca^{++}$ concentration (Km, 10-30 nM), the other is low affinity $Ca^{++}-ATPase$ activated in higher $Ca^{++}$ concentration $(K_{1/2},\;40\;{\mu}M)$. At certain $Ca^{++}$ concentrations, activities of high and low affinity $Ca^{++}-ATPase$ are the highest in light membrane fractions and are the lowest in microsomal fractions. It appeares that high affinity $Ca^{++}-ATPase$ system have 2 binding sites for ATP (Hill's coefficient; around 2 in all membrane fractions measured) and the positive cooperativity of ATP bindings obviously existed in each membrane fractions. The optimum pH for high affinity $Ca^{++}-ATPase$ activation is around S in all membrane fractions measured. The lipid phase transition temperature measured by Arrhenius plots of high affinity $Ca^{++}-ATPase$ activity is around $25^{\circ}C$. The activation energies of high affinity $Ca^{++}-ATPase$ below the transition temperature are similar in each membrane fractions, but at the above transition temperature, it is the hightest in heavy membrane fractions and the lowest in microsomal fractions. According to the above results, it is suggested that intracellular $Ca^{++}$ level, which may regulate the luteal function, may be adjusted primarily by the high affinity $Ca^{++}-ATPase$ system activated in intracellular $Ca^{++}$ concentration range $(below\;0.1\;{\mu}M)$.

• Journal of Veterinary Clinics
• /
• v.12 no.1
• /
• pp.877-886
• /
• 1995

The recycling nuclear transplantation(NT) technique has the powerful potential of producing a large number of genetically identical embryos and offsprings from one embryo. Multiple generational cloning by this technique utilizes the NT embryo itself as the donor for the next generation of cloning. In this experiment, we have produced the third generational cloned embryos by recycling NT. Further we examined comparatively the electrofusion rate and in vitro developmental potential in the cloned embryos of the first second and third generations. The embryos of 16-cell stage were collected from the mated does by flushing oviducts with Dulberco's phosphate buffered saline containing 10 % fetal calf serum(FCS) at 47 hours after hCG injection. In the first generation NT, the nuclear donor embryos were synchronized in the phase of Gl/S transition of 32-cell stage. The first and second generation NT embryos developed to 16-cell were used as donor nuclei for second and third generation. The recipient cytoplasms were utilized the oocytes collected at 14 hours after hCG injection, following revoming the nucleus and the first polar body by micromanipulation. The separated blastomeres were injected into the enucleated recipient oocytes by micromanipulation and were fused by electrical stimulation. The electrofusion rate was seen to be 78.0, 88.0 and 90.3 % in the first second and third generation NT rabbit embryos, respectively. The fused oocytes were co-cultured with a monolayer of rabbit oviductal epithelial cells in M-199 solution containing 10 % FCS for 120 hours at 39$^{\circ}C$ in a 5% $CO_2$ incubator. The in vitro developmental potential to blastocyst stage was significantly(P<0.05) decreased in the third(7.2 %) generation NT embryos compared to the first(53.1 %) and second(16.1 %) generation NT embryos. Following in vitro development to blastocyst stage, they were stained with Hoechst 33342 dye for counting the number of blastomeres by fluorescence microscopy. The mean blastomere numbers and cell cycle numbers of NT embryos during the culture period were significantly(p<0.05) decreased in the second(93.9 cells and 6.55 cylces) and third(81.5 cells and 1.35 cylces) generation, compared to the first(189.9 cells and 7.55 cylces) generation.