• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.1 s.109
• /
• pp.1-9
• /
• 2005

Many factors which affect the adsorption of cationic polymers on fibers and fines have been investigated by many researchers that include contact time, pH, collision frequency, properties of cationic polymers and adsorbent, etc. But the effect of white water quality on the adsorption of cationic polymer have not been examined throughly. In this study, the adsorption of cationic PAM was analyzed as a function of white water quality. The adsorption of the cationic PAM was analyzed by two analysis methods, Kjeldahl nitrogen content measurement and electrokinetic measurements. When the distilled water was used, adsorbed amount of C-PAM and zeta-potential of fibers increased as a function of the addition of C-PAM. When closure level increased, nitrogen content of fibers increased indicating that the cationic PAM was adsorbed. Zeta-potential of fibers, however, showed no significant change with the increased addition of C-PAM. This showed that adsorption of C-PAM was not reflected by zeta-potential of fibers due to the deteriorated efficiency of C-PAM by the anionic contaminants in white water.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.812-818
• /
• 2000

We studied the effects of Ge preamorphization (PAM) on 0.25$\mu\textrm{m}$ Ti-salicide junctions using comparative study with As PAM. For each PAM schemes, ion implantations are performed at a dose of 2E14 ion/$\textrm{cm}^2$ and at 20keV energy using $^{75}$ /As+and GeF4 ion sources. Ge PAM showed better sheet resistance and within- wafer uniformity than those of As PAM at 0.257m line width of n +/p-well junctions. This attributes to enhanced C54-silicidation reaction and strong (040) preferred orientation of the C54-silicide due to minimized As presence at n+ junctions. At p+ junctions, comparable performance was obtained in Rs reduction at fine lines from both As and Ge PAM schemes. Junction leakage current (JLC) revels are below ~1E-14 A/$\mu\textrm{m}^{2}$ at area patterns for all process conditions, whereas no degradation in JLC is shown under Ge PAM condition even at edge- intensive patterns. Smooth $TiSi_2$ interface is observed by cross- section TEM (X- TEM), which supports minimized silicide agglomeration due to Ge PAM and low level of JLC. Both junction break- down voltage (JBV) and contact resistances are satisfactory at all process conditions.

• Horticultural Science & Technology
• /
• v.16 no.2
• /
• pp.222-225
• /
• 1998

The objective of this study was to observe the effects of potassium-carboxymethyl cellulose (K-CMC), which is a natural polymer derivative, and polyacrylamide (PAM), which is a commercial synthetic polymer, on soil physicochemical properties and yields of the cabbage. To increase water absorbing capacity (WAC), hydrophilic carboxymethyl group was introduced to cellulose chain and it was confirmed by FT-IR. WAC was tested by tea-bag method in distilled water and 3% NaCl solution. PAM is slightly more absorptive than K-CMC in distilled water, but in NaCl solution, K-CMC is more absorptive than PAM. Soil particle sizes above $1_{mm}$ were immediately increased from 9.6 to approximately 16.6% by the application of K-CMC and PAM, respectively. Infiltration rates of soil were approximately twice as great as those of the control when conditioned with the K-CMC and PAM treatment. K content of soil treated with K-CMC was significantly higher than those of PAM and control, but the other components of soil chemical properties were not different. The early growth and vegetative production of cabbage in the K-CMC and PAM treatments were significantly higher than the control. The contents of vitamin C were increased with the treatment of K-CMC. It was proposed that K-CMC treatment influence K component of the soil and vitamin C content of the cabbage, therefore, it improved the yields as well as crop quality.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.251-256
• /
• 2006

The purpose of this study was to confirm multiple retention system of C-PAM, A-PAM and Inorganic micro particles vs. traditional micro particle system and dual polymer system by measuring retention, drainage and formation using RDA HSF and Techpap 2D -F Sensor The benefits of dual polymer system were easy to use, low chemical consumption and good retention property but defect was worse drainage property than inorganic microparticle systems. On the other hand, Inorganic microparticle system had benefit of good drainage effect but defects were difficult to use, high chemical consumption. Therefore, we tried to find optimal morphology of polyacrylamide and applied to multiple retention system of C-PAM, A-PAM and inorganic microparticles to compensate defects of both of retention systems. As a result, we found the performance of branched C-PAM, branched A-PAM and inorganic micro particle triple system was more appropriate than traditional inorganic mircoparticle systems or dual polymer systems by comparing retention, drainage and formation.

• Membrane Journal
• /
• v.23 no.4
• /
• pp.312-318
• /
• 2013

Poly vinylidene fluoride (PVDF) hollow fiber membranes were hydrophilized using polyethylenimine (PEI) and p-xylylene dichloride (XDC), and poly(vinyl alcohol) (PVA) and poly (acrylic acid -co- maleic acid) (PAM) mixed solutions by varying the concentration of PAM were coated onto PVDF membrane surface. The surface coating was verified by the observation of scanning electron microscope (SEM) and the permselective characteristcs of the resulting composite membranes were tested for 90 wt% aqueous ethanol solution by the pervaporation technique. The effects of the corsslinking agent concentraion, the temperature of feed solution, and the reaction temperature on the flux and separation factors were measured. Typically, the flux, $1,480g/m^2hr$ at the reaction temperature $100^{\circ}C$, PAM 3 wt%, feed temperature $70^{\circ}C$ was obtained, on the other hand, for the separation factor, ${\alpha}_{W/E}=82$ at the conditions of the reaction temperature $100^{\circ}C$, PAM 15 wt% and feed temperature $25^{\circ}C$ was shown.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.1-9
• /
• 2006

Increasing the filler content of sheet provides an opportunity for saving production cost through fiber replacement with relatively low-priced filler. But increasing the filler content tends to decrease the strength of paper and filler retention. To overcome these problems, preflocculation technology of fillers has been suggested. To evaluate the effect cationic polymers on the size and size distribution of preflocculated GCC and their shear stability, cationic PAM and cationic starch were used. Results showed that cationic PAM formed large prefloc at low dosage. It was required to add 15 times as high as cationic starch to cationic PAM to obtain the same size prefloc. But preflocs formed with cationic starch was superior in shear stability to those formed with cationic PAM. With the increase of shear rate the size of preflocs decreased. Greater amount of small preflocs or un-flocculated fillers was observed when the dosage of polymers was low and this ended up low ash retention in handsheets.

• Parasites, Hosts and Diseases
• /
• v.22 no.2
• /
• pp.253-258
• /
• 1984

Experimentally, primary amoebic meningoencephalitis (PAM) is induced by Naegleria fowleri in mouse and development of PAM may be inauenced by the strain, weight and sex of mouse, and inoculum size of N. fowleri trophozoite. In this paper, the effect of these factors on PAM development of mouse was studied. N. fowleri trophozoites, strain 0359, were introduced into mouse intranasally under secobarbital anesthesia (0.05mg/g). 1. PAM was developed more frequently in BALB/C mouse than ICR mouse. 2. The survival time of mouse with PAM was influenced by the weight, that is, it was shorter in 15 g mouse than in the heavier groups. 3. No difEerence was observed on PAM development according to sect. 4. In case of inoculated amoeba, PAM incidence of $0.5{\times}10^4$ was markedly decreased.

• Membrane Journal
• /
• v.14 no.2
• /
• pp.117-125
• /
• 2004

Proton exchange membrane composed of PVA/PAM/ZrP was prepared and effect of PAM and ZrP contents on properties and performance of the membrane were investigated. PAM as a crosslinking agent was mixed into PVA solution with different concentration (7∼11 wt%) and the PVA/PAM solution was cast to prepare PVA/PAM crosslinked membrane. The membrane was treated in the solution of zirconyl chloride and phophoric acid to make a PVA/PAM/ZrP composite membrane. Methanol permeability, ion conductivity, swelling and ion exchange capacity of the membranes with different ZrP concentration were $10^{-8}∼l0^{-6}$ $\textrm{cm}^2$/sec, $10^{-3}~10^{-2}$ S/cm, 0.26∼1.17 g $H_2O$/g membrane and 2.59∼5.1 meq/g membrane, respectively. Hethanol permeability and ion conductivity of the PVA/PAM/ZrP membrane were improved by 18% and 23%, respectively, compared to those of the PVA/PAM membrane.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.4
• /
• pp.244-251
• /
• 2001

Over half of all biologically active peptide and peptide hormones are $\alpha$-amidated at their C-terminus, which is essential for their full biological activities. Amidation is accomplished through the sequential reaction of the two enzymes encoded by the single bifunctional, peptidyl-glycine $\alpha$-amidating monooxygenase (PAM or an $\alpha$-amidating enzyme). PAM catalyze the forma - tion of a peptide amide from peptide precursors that include a C-terminal glycine, and requires copper molecular oxygen and ascorbate. PAM is the only enzyme that produces peptide amides in vivo. However various strategies utilizing PAM, carboxypeptidase-Y enzymes, and chemical syn-thesis have been developed for producing peptide amides in vitro. The growing need and impor-tance of peptide amide drugs has highlighted the necessity for a efficient in vitro amidating sys-tem for industrial application for the production of peptide hormones, like calcitonin and oxytocin. This review presents the current situation regarding amidation with a special emphasis on the in-dustrial production or peptide hormones.

• Macromolecular Research
• /
• v.13 no.4
• /
• pp.314-320
• /
• 2005

Crosslinked poly(vinyl alcohol) (PVA) membranes were prepared at various crosslinking temperatures using poly(acrylic acid-co-maleic acid) (PAM) containing different PAM contents. The thermal properties of these PVA/PAM membranes prepared at various reaction temperatures were characterized using differential scanning calorimetry (DSC). The proton conductivity and methanol permeability of PVA/PAM membranes were then investigated as PAM content was varied from 3 to 13 wt%. It was found that the proton and methanol transport were dependent on PAM content in their function both as crosslinking agent and as donor of hydrophilic -COOH groups. Both these properties decreased monotonously with increasing PAM concentration. The proton conductivities of these PVA/PAM membranes were in the range from $10^{-3}\;to\;10^{-2}S/cm$ and the methanol permeabilities from $10^{-7}\;to\;10^{-6}cm^{2}/sec$. In addition, the effect of operating temperature up to $80^{\circ}C$ on ion conductivity was examined for three selected membranes: 7, 9 and 11 wt% PAM membranes. Ion conductivity increased with increasing operating temperature and showed and S/cm at $80^{\circ}C$, respectively. The effects of crosslinking and ionomer group concentration were also examined in terms of water content, ion exchange capacity (IEC), and fixed ion concentration. In addition, the number of water molecules per ionomer site was calculated using both water contents and IEC values. With overall consideration for all the properties measured in this study, $7{\sim}9\;wt%$ PAM membrane prepared at $140^{\circ}C$ exhibited the best performance. These characteristics of PVA/PAM membranes are desirable in applications related to the direct methanol fuel cell (DMFC).