• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.4
• /
• pp.923-928
• /
• 2010

Anodic aluminum oxide (AAO) nanotemplates for nano electronic device applications have been attracting increasing interest because of ease of fabrication, low cost process, and possible fabrication in large area. The size and density of the nanostructured materials can be controlled by changing the pore diameter and the pole density of AAO nanotemplate. In this paper, nano porous alumina films AAO nanotemplate was fabricated by second anodization method using sputterd Al films. In addition, effects of electrolyte temperature and anodization voltate on the microstructure of porous alumina films were investigated. As the electrolyte temperature was increased from $8^{\circ}C$ to $20^{\circ}C$, the growth rate of nanoporous alumina films was increased from 86.2 nm/min to 179.5 nm/min. The AAO nanotemplate fabricated with optimal condition had the mean pore diameter of 70 nm and the pore depth of $1\;{\mu}m$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.11-16
• /
• 2016

Silicon carbide (SiC) has received significant attention over the past decade because of its high-voltage, high-frequency and high-thermal reliability in devices compared to silicon. Especially, a SiC Schottky barrier diode (SBD) is most often used in low-voltage switching and low on-resistance power applications. However, electric field crowding at the contact edge of SBDs induces early breakdown and limits their performance. To overcome this problem, several edge termination techniques have been proposed. This paper proposes an improvement in the breakdown voltage using a double-field-plate structure in SiC SBDs, and we design, simulate, fabricate, and characterize the proposed structure. The measurement results of the proposed structure, demonstrate that the breakdown voltage can be improved by 38% while maintaining its forward characteristics without any change in the size of the anode contact junction region.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2512-2517
• /
• 2007

Effect of natural convention for hot plate surface temperature uniformity was studied by experiments that were adjusted height of chamber and temperature difference. The hot plate chamber is composed of the hot plate and the upper heater and adiabatic vertical wall. The hot plate diameter is 220mm and maintains temperature at $150^{\circ}C$. Flow pattern compares with surface temperature and confirms that natural convection affects on temperature uniformity of hot plate surface. In case, temperature non-uniformity of hot plate surface is due to heater pattern, lots of weak and small flow cells more improve temperature uniformity than stronger flow cells or non-developing flow cell. Improve temperature uniformity $1.2^{\circ}C$ when developing weak and small flow cells.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.341-350
• /
• 1997

The objective of this study is to investigate the structural behavior of the composite slabs with the new metal deckplate. The new deckplate can be used as structural member with topping concrete. So several experiments of this structural test and the fire resistance test were done. From this experiments. slabs with new metal deckpklate were verified as composite slabs. In this paper, this verifications were compared with the international design methods. For experiment. 49 specimens were made. the main parameters are deckplate thickness (1.2mm. 1.6mm) depth of topping concrete(85mm. 90mm). support condition(simple, 2-span), shear reinforcment(studs), span(2.7m, 3.0m, 3.3m. 3.6m. 3.9m) and shear span(L/3, L/4, L/7). We analyzed the structural behavior of composite slab throughout the moment-curvature relationship which is obtained with the program using the computer language. Turbo C. From this development for slab system, the reinforced concrete or steel structure building may be easy, economical for construction, And informations about the structural behavior of composite slabs will be utilized to established korea standard.

• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.776-784
• /
• 1993

A pentasil zeolite, ZSM-5 was synthesized in the absence of organic template, $TPA^+$ ion at $210^{\circ}C$. It was realized that a conventional method can not be applied to the synthesis system where organic templates are not used. The results indicated that the compositional range for the crystallization of ZSM-5 is very narrow, requiring very careful controls in the $Na_2O/SiO_2$and $SiO_2/Al_2O_3$ratios. In addition, the results showed that the effects of mixing method, aging and reaction time on the crystallization of ZSM-5 were extraordinarily significant.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.798-805
• /
• 2010

There are no domestic researches of plate fin heat exchanger in the field of cryogenic such as LNG FPSO liquefaction plant. In this study, condensing heat transfer characteristics of nitrogen according to three kinds of fin type in the plate fin heat exchanger were analyzed through simulation and experiment to secure independent technologies. In the simulation, nitrogen was condensed at 69bar and $-140^{\circ}C$ in serrated and wavy fin of plate-fin heat exchanger. The serrated fin shows the highest value of local heat transfer coefficient, followed by wavy and plain fin. The experimental results were shown errors less than 12% comparing with the simulation results.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.257-266
• /
• 2006

Flat-plate building systems are utilized extensively for construction of apartments, hotels and office buildings because of short construction period, low floor-to-floor height and flexibility in plan design. Recently, to increase lateral seismic resistance of flat-plate building systems, wall-columns are used frequently. Therefore, to estimate strength of flat-plate column connection accurately, the effect of column section shape on the behavior of flat-plate column connection should be considered properly, In the present study, a numerical analysis was performed for interior connections of continuous flat-plate to analyze the effect of column section shape. For the purpose, a computer program for nonlinear FE analysis was developed, and the validity was verified. Through the parametric study, the variations of shear stress distribution around the connection were investigated. According to the result of numerical analysis, as the length of the cross section of column in the direction of lateral load increases, the effective area and the maximum shear strength providing the torsional resistance decrease considerably. Therefore, these effects should be considered properly to estimate the strength of flat-plate connection accurately.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04a
• /
• pp.43-43
• /
• 1999

98년말 동일제지에 도입 설치된 Condebelt 설비는 세계 최초의 대형생산설비로 국제적 인 관심을 모으고 있다. 이러한 첨단 Condebelt 기술의 국산화를 위해서는 국내 원료 특성 에 적합하도록 공정최적화가 요청된다. 본 연구에서는 KOCC를 원료로 이용한 라이너지를 C Conde belt를 이용하여 생산할 경우 주요 공정변수에 따른 물성 변화를 평가하고, 이를 통하 여 Condebelt 공정을 최적화하고자 실험실용 파일로트 건조기를 이용하여 Condebelt 공정의 주요 변수가 지질에 미치는 영향을 검토하였다. 실험용 Condebelt 건조장치의 상부플레이트는 18WC까지, 하부플레이트는 냉각수를 이용 하여 40-80'C까지 조절이 가능하도록 설계하였으며, 유압을 이용하여 압체 압력과 시간을 변화시킬 수 있도록 하였다. 구축된 실험장치를 이용하여 Conde belt 공정의 주요 변수인 온도, 압력, 압체시간, 유입 지필의 건조도 변화에 따른 라이너지의 물성 변화를 평가하고 이를 실린더 건조된 종이의 물성과 비교하였다. 그 결과 본 연구에서 검토된 모든 건조조건에서 Conde belt 건조된 종이가 실린더 건조 된 종이보다 높은 강도를 나타내었으며, 투기저항성과 광택도 역시 향상되었다. 투기저항성 과 광택도는 강도적 성질과 달리 유입지 건조도가 높을수록, 상부플레이트의 온도가 높을수 록 그 효과가 저하되었다. 일반적으로 KOCC를 원료로한 라이너지를 Conde belt로 제조할 경우 상부 고온챔버의 온도를 160'C, 압체압력을 5 bar로 조절하는 것이 가장 좋을 것으로 판단되었다. 원료펄프의 조성에 따른 Condebelt 공정의 건조효과를 연구한 결과 모든 펄프에서 공히 C Condebelt 건조방법이 실린더 건조방법에 비하여 물성 향상 효과가 있는 것으로 나타났으 며, 그 효과는 펼프의 리그닌 함량이 높을수록 크게 나타났다. 또 Condebelt의 물성개선 특 성을 이용한 원료비 절감 가능성을 평가하기 위해 AOCC와 KOCC를 이용하여 단층지와 이 층지를 제조하고 물성을 비교평가하였다. 그 결과 Condebelt를 이용하면 KOCC의 비율을 증가시키더라도 AOCC만을 이용하여 실린더 건조한 종이보다 우수한 물성을 얻을 수 있었다. 이러한 연구를 통하여 Condebelt 공정이 국내 저급원료로 제조된 종이의 강도 저하를 극복할 수 있는 기술임을 확인하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.121-129
• /
• 2007

The aim of this study is to investigate punching shear strength of exterior connections in the flat plate structure with rectangular column. To inspect the effect of column aspect ratios on the punching shear behavior, eight specimens for exterior connection were made and tested. In this experimental program the length of critical perimeter was kept constant, while column aspect ratio varied from 2.0 to 4.5. Two levels of concrete strength and slab reinforcement ratio were also considered. As the column aspect ratio increased, the punching shear strengths are decreased. The decrement of punching shear strength was small in specimens with high aspect ratio of column.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1377-1378
• /
• 2010