• Journal of the Korean Society of Safety
• /
• v.16 no.1
• /
• pp.31-36
• /
• 2001

Surface crack growth characteristics and influence of the stress amplitude in rotary bending fatigue test were evaluated for annealed S35C steel, and than fractal dimensions of fatigue crack paths estimated using the box counting method. The following results that will be helpful to understand the fatigue crack growth mechanism were obtained. (1) Crack growth rate ds/dN and db/dN (s : half crack length at the surface crack, b : crack depth) depended on stress amplitude (${\Delta}{\sigma}/2$), stress intensity factor range (${\Delta}K_A, {\Delta}K_C$) and crack length. (2) At the effect area of 0.3 mm hole notch (s＜0.5 mm) crack growth rate did not depend on these factors. (3) The fractal dimensions (D) increased with stress amplitude (${\Delta}{\sigma}/2$) but decreased with cyclic number.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.33-39
• /
• 1997

The crystallization temperature of an amorphous silicon (a-Si) can be lowered down to 400.deg. C by a new method : Double-metal induced lateral crystallization (DMILC). The a-Si film was laterally crystallized from Ni and Pd deposited area, and its lateral crystallization rate reaches up to 0.2.mu.m/hour at that temperature and depends on the overlap length of Ni and Pd films; the shorter the overlap length, the faster the rate. Poly-Silicon thin film transistors (poly-Si TFT's) fabricated by DMILC at 400.deg. C show a field effect mobility of 38.5cm$^{3}$/Vs, a minimum leakage current of 1pA/.mu.m, and a slope of 1.4V/dec. The overlap length does not affect the characteristics of the poly-Si TFT's, but determines the lateral crystallization rate.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.4
• /
• pp.98-104
• /
• 2000

Commercial rubber(IR, NR, BR), SBR, and tire were degraded by thermal degradation process. The oil yield of rubbers and tire ranges about 37~86%, it was increased with increase of operation temperature in pyrolysis. And the yield of pyrolytic oil was increased with increase of heating rate. The maximum oil yields of IR, NR, BR, SBR, and tire were 80, 73, 83, 86 and 55% each at $700^{\circ}C$ with a heating rate of $20^{\circ}C$/min, respectively. The pyrolytic oil components were consisted of about 50 aromatic compounds. The calorific value of purolytic oil of commercial rubber, SBR, and tire was measured by calorimeter, it was 39~40 kJ/g. The BET surface area of pyroblack was $47~63m^2/g$. The optimum condition of pyrolysis was operating temperature of $700^{\circ}C$ with heating rate of $20^{\circ}C$. Therefore, the pyrolytic oil and pyroblack are possible to alternative fuel and carbon black.

• Journal of the Korean Society of Safety
• /
• v.1 no.1
• /
• pp.27-32
• /
• 1986

To remove sulfur dioxide from flue gas by the method of metal oxide, copper powder of average diameter $2.4\mu\textrm{m}$and $51\mu\textrm{m}$ were used in a fixed bed reactor over a, temperature range of $300^{\circ}C-500^{\circ}C$. Copper oxide reacts with sulfur dioxide producing cupric sulfate and it can be regenerated from the latter by using hydrogen or methane. Experimental results showed that the reaction rate was increased by the increase of reaction temperature in the range of $300^{\circ}C-422^{\circ}C$ and the removal efficiency of sulfur dioxide was high in case of small size copper particle. However the removal efficiency was decreased at higher temperature due to decomposition of cupric sulfate. The rate controlling step of this reaction was chemical reaction and deactivating catalysts model can be applied to this reaction. The rate constants for this reaction and deactivation are as follows ： k＝8,367exp(-10,298/RT) Kd＝2.23exp(-8,485/RT)

• Korean Journal of Animal Reproduction
• /
• v.14 no.3
• /
• pp.199-204
• /
• 1990

Equine semen was analysed for its survival after storage under different conditions. Total 12 ejaculates from 2 Thoroughbred were analysed for general characterisitcs and preservation at low temperature. The sperm fraction, concentration, nd the rate of motile spermatozoa were 57.91ml per ejaculate, 2.18$\times$108/ml and 74.1%, respectively. The survival rate of spermatozoa was highest when diluted semen with E-Z Mixin was stored at 7~8$^{\circ}C$. The optimum survival rate(>54%) can be obtained upto 24h at 7~8$^{\circ}C$. However only 10% spermatozoa survived after 5h storage at 7~8$^{\circ}C$ without use of E-Z Mixin. Other ranges of temperature(15$^{\circ}C$ and room temperature) gave less survival rates(<25%). These results indicate that the extender could be used as a basic solution for the preservation of equine spermatozoa at low temperature. It also provides a practical method for short-term storage of collected equine semen in a simple manner.

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.66-70
• /
• 1999

In order to investigate the quantitative behavior of galvanic corrosion in weld joints between stainless std이 and carbon steel, electrochemical polarization experiments were performed at pH4, pH7 and pH10 with boric acid concentration 4000ppm, and water temperature were selected as $35^{\circ}$C and $60^{\circ}$C. As the results, the galvanic corrosion phenomena of carbon steel weld material at $60^{\circ}$C was revealed $2{1\over2}$ times higher corrosion rate than that at $35^{\circ}$C condition. The corrosion rate of stainless steel was almost inedependent of the variation of pH. The significant corrosion rates of carbon steel and the weld joint of carbon-carbon steel were observed at pH 4.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.229-231
• /
• 2005

Friction surfacing of STS304 consumable rod on S45C substrate was investigated by microstructural observation and mechanical tests. STS304 layer formed a strongly-bonded thick layer under a wide range of surfacing conditions. The hardness distribution showed the peak value in the boundry layer, while the highest coating efficiency obtained in the condition of 1000rpm-2.5mm/sec-2.5mm/sec. As the consumable rotation rate and the traveling rate increased, the coating efficiency tended to decrease. On the other hand, as the feeding rate increased, the coating efficiency appeared to be increased.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.87-92
• /
• 1998

Major characteristics of shrinking and rehydration of Korean tea-leaves were investigated in the hot-air drying equipment. Experiments were performed with various drying temperature, plucking time, heating method and rolling condition. The values of shrinking raito and rate were the highest at 7$0^{\circ}C$ in the range of 3$0^{\circ}C$ to 9$0^{\circ}C$. The 1st tea-leaves and showed higher values. Shrinking ratio was 16.62 and 19.62% for leaves and stems; shrinking rate was found 0.083 and 0.091cm/hr.cm, respectively. The rehydration characteristics of tea-leaves at the drying temperature of 3$0^{\circ}C$ were fairly satisfactory. The 2nd tea-leaves showed higher value than others, while the natural tea-leaves were lower. Average rehydration ratio and rehydration rate constant were 85.7% and 0.063/min for leaves; 80.1% and 0.032/min for stems, respectively.

• Electrical & Electronic Materials
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1988

Sintered CdS/CdTe solar cells have been farbricated by coating a (Cd+Te) slurry on sintered CdS films followed by the sintering at 625.deg.C for one hour with various heating rates. When cadmium and tellurinm powders are used instead of CdTe powder to form CdS/CdTe junction, CdTe is formed in the temperature range of 290.deg.C-400.deg.C. The microstructure of the CdTe films depends strongly on the heating rate of the sintering due to the low melting temperature and the high vapor pressure of the elemental Cd and Te. An optimum heating rate obtain CdTe films with uniform and dense microstructure which, in turn, improves the efficiency of the sintered CdS/CdTe solar cells. All-polycrystalline CdS/CdTe solar cells with an efficiency of 9.57% under 50mW/cm$^{2}$ tungsten light have been farbricated by using a heating rate of 14.deg.C/min.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.2
• /
• pp.37-44
• /
• 1990

The effect of the microstructural change on the near threshold fatigue crack growth rate in SM40C steel has been studied using the ${\Delta}K$ decreasing method. Below the total strain amplitude of 0.56%, cyclic softening occured, whereas above this value cyclic hardening occurred in the pearlitic lamellar structure. However, in the spherodized structure the cyclic hardening solely occurred. The crack growth rate in the near-threshold region was decreased with increasing prior austenite grain size and this was due to surface roughness. The crack growth rate of the spherodized structure was lower than that of the pearlite lamellar structure and the ${\Delta}K_{th}$ of the former was higher than that of the latter. It was understood that the crack propagates preferentially through the ferrite phase. The intergranular facets in the near-threshold region appeared in the spherodized structure.