• Journal of the Korean Ceramic Society
• /
• v.28 no.8
• /
• pp.626-634
• /
• 1991

The specimens for the corrosion test were made by hot-pressing of SiC power with 2 wt% Nl2O3 and 10wt% Al2O3 additions at 200$0^{\circ}C$ and 205$0^{\circ}C$. The specimens were corroded in 37 mole% NaCl and 63 mole% Na2SO4 salt mixture at 100$0^{\circ}C$ up to 60 min. SiO2 layer was formed on SiC and then this oxide layer was dissolved by Na2O ion in the salt mixture. The rate of corrosion of the specimen containing 10 wt% Al2O3 was slower than that of the specimen containing 2 wt% Al2O3. This is due to the presence of continuous grain boundary phase in the specimen containing 10 wt% Al2O3. The oxidation of SiC produced gas bubbles at the SiC-SiO2 interface. The rate of corrosion follows a linear rate law up to 50 min. and then was accelerated. This acceleration is due to the disruption oxide layer by the gas evolution at SiC-SiO2 interface. Pitting corrosion has found at open pores and grain boundaries.

• Korean Journal of Plant Resources
• /
• v.13 no.1
• /
• pp.18-24
• /
• 2000

Pepper (Capsicum annum L.) used as a spice or fruit vegetable has been transplanted for cultivation to accompany the production of its seedlings in general. The experiment was done to measure the effect of its cultivars (Daemyng; Wanggochu), priming (chemicals; concentration; period), light quality (red; far-red; blue; dark) during priming, and germination temperature (25 or 15$^{\circ}C$ constant; 25/15$^{\circ}C$ alternating) on the rate of germination done under incandescent lamps until 9 days after sowing. Seed germination was better when primed with Ca(NO$_3$)$_2$ than with KNO$_3$. Priming for 6 to 12 days using the former chemical enhanced the final germination rate and shortened the elapsed days to 50% germination, $T_{50}$, compared to no-priming. Under $25^{\circ}C$ constant germination temperature, primed seeds at darkness or far-red light showed the highest rate until 5 days after sowing or the lowest one since 7 days after sowing, respectively. The germination response at 25/15$^{\circ}C$ alternating temperature did not followed the lowest rate of 15$^{\circ}C$ constant germination temperature but inclined to that of $25^{\circ}C$ constant recorded the greatest one. Under 3 germination temperature red light treated during priming elevated the rate since 7 days after sowing compared to the other light treatments, and the germination rate of each cultivar was affected by no-priming or priming, light quality during priming. which imply their interaction to the seed germination.

• Journal of Aquaculture
• /
• v.6 no.3
• /
• pp.159-171
• /
• 1993

The effects of environmental factors (density, light, temperature) and live food on growth and survival rate of zoea and mysis of fleshy shrimp, Penaeus chinensis, were examined. The percent survival rates at the culture densities of 200 and 300 larvae per liter were significantly higher than that of 500 larvae per liter (p< 0.05). The percent survival rates at the culture densities of 100, 200, 300 and 500 larvae per liter were $90.3^{ab},\;95.2^a,\;94.3^a\;and\;86.7^b\%$ (p< 0.05). The effects of light conditions with diatom premix diet showed that continuous light was the best for the survival rate, $96.5\%$. Natural light and continuous darkness showed the survival rates $79.0\%\;and\;4.3\%$, respectively. On the rearing temperature, the survival rates were $97.3\%\;at\;19^{\circ}C\;and\;96.7\%\;at\;22^{\circ}C$ with little difference but the higher temperature resulted in faster growth. The survival rate was $51.6\%;at\;25^{\circ}C$ thus showing significant decrease compared to $19^{\circ}C\;and\;22^{\circ}C$. At this temperature the growth was also suffered. With regard to dietary value of live food, both the best survival rate and the fastest growth were obtained when 6 mixed species of diatom (A. normaii, C. simplex, N closterium, P. tricornutum, S. costatum and T. weissflogii) were provided. When single species was supplied the best survival rate $(82.1\%)$ was obtained with S. costatum, but the other species resulted in much inferior survival rates $(below\;80.0\%)$ and poor growth.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.39-45
• /
• 1995

The plywoods commonly used as decorative interior materials for the construction are inflammable and so it is a causative factor for making fire accidents, resulting in the destruction of human life and personal properties. Indeed, it is, therefore, required to produce fire-retardant plywoods. In this study, a special grade of defect-free, Kapur plywood was used. Specimens were cut into 3- by 20cm dimensions from 120- by 240- by 0.33-cm panels(thin panel) or 120- by 240- by 0.5-cm panels(thick panel). Some specimens were treated with diammonium phosphate(DAP), but some were not treated with diammonium phosphate to use as control panels. Chemical absorption, drying curves, drying rates and dynamic Young's modulus were investigated. The results were summaries as follows; 1. The specimens were soaked into 19% diammonium phosphate solution by a full cell pressure process and the diammonium phosphate retained in the thin and thick plywoods was 1.409kg/$(30cm)^3$, 1.487kg/$(30cm)^3$, respectively. 2. Diammonium phosphate-treated plywoods were redried with press-drying process at one of either condition dried on the platen($115^{\circ}C$) for a period of time or dried on the platen($50^{\circ}C$) for 3 hrs plus in a dry-oven($30^{\circ}C$) for 24 hrs. or dried on the platen($60^{\circ}C$) for 2 hrs plus in a dry-oven($30^{\circ}C$) for 24 hrs. The drying rate of treated thin specimens dried at $60^{\circ}C$ plus $30^{\circ}C$ and $115^{\circ}C$ only was found to be 0.04 %/min. and 8.53 %/min. Similarly, the drying rate of treated thick specimens were 0.03 %/min. and 6.77 %/min. respectively. 3. It was evident that highly-significantly different drying rate of treated plywoods was observed between plywood thicknesses and platen temperatures and the rate was increased by elevating the platen temperature up to $115^{\circ}C$. Based on the two-way variance analysis, highly significant drying rate was observed from the interaction between plywood thicknesses and platen temperatures. 4. After redrying, the specimens were weighed and reconditioned to a constant weight in a facility maintained temperature ($20^{\circ}C$) and relative humidity(65%) prior to test dynamic Young's modulus. The test revealed that the thin specimens dried at the platen temperature of $50^{\circ}C$, $60^{\circ}C$, $115^{\circ}C$ and untreated specimens showed 1.070E+09 dyne/$cm^2$, 1.156E+09 dyne/$cm^2$, 1.243E+09 dyne/$cm^2$, and 1.052E+09 dyne/$cm^2$, respectively. Likewise, the thick specimens revealed 5.647E+09 dyne/$cm^2$ 5.670E+09 dyne/$cm^2$, 6.395E+09 dyne/$cm^2$ and 5.415E+09 dyne/$cm^2$, respectively. 5. It was evident that significantly different dynamic Young's modulus was observed between the plywood thickness and the platen temperature, but not in the two-way interaction between the plywood thickness${\times}$the platen temperature.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.438-442
• /
• 2005

Granule swelling is essential phenomenon of starch gelatinization in excess water, and characteristic of heated starch dispersion depends largely on size and distribution of swelled starch granule. Although swelling characteristic of starch granules depends on type of starch, heating rate, and moisture content, influence of heating rate on swelling phenomenon of starch granule has not been fully discussed, because constant heating rate of starch dispersion cannot be obtained by conventional heating method. Ohmic heating, electric-resistant heat generation method, applies alternative current to food materials, through which heating rate can be easily controlled precisely and conveniently at wide range of constant heating rates. Starch dispersion heated at low heating rates below $7.5^{\circ}C/min$ showed Newtonian fluid behavior, whereas showed pseudoplastic behavior at heating rates above $16.4^{\circ}C/min$. Apparent viscosity of starch dispersion increased linearly with increasing heating rate, and yield stress was dramatically increased at heating rates above $16.4^{\circ}C/min$. Average diameter of corn starch granules during ohmic heating was dramatically increased from $30.97\;to\;37.88\;{\mu}m$ by increasing heating rate from $0.6\;to\;16.4^{\circ}C/min$ (raw corn starch: $13.7\;{\mu}m$). Hardness of starch gel prepared with 15% corn starch dispersion after heating to $90^{\circ}C$ at different heating rates decreased gradually with increasing heating rate, then showed nearly constant value from $9.4\;to\;23.2^{\circ}C/min$. Hardness increased with increase of heating rate higher than $23.2^{\circ}C/min$.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.1
• /
• pp.86-92
• /
• 2012

To promote the practical use of livestock manure compost (LC) for paddy rice cultivation, the fertilization efficiency of nutrients in LCs was investigated compared to that of chemical fertilizer. This experiment was conducted at rice field in Hwaseong, Korea, with 6 treatments by each of 3 kinds of tested LCs, cattle manure compost (CaC), swine manure compost (SwC) and chicken manure compost (ChC). The treatments consisted of 3 application levels of LCs and 3 chemical fertilizer treatments having the same application levels with LCs. $NH_4$-N content in soil became higher according to the increase in the urea application rate, while it became lower in LC plots than in urea plots, and statistically had no significant difference among LC plots. There was a close relationship between phosphate fertilization rate and the increment of soil available phosphate content after experiment resulting y = 0.1788x - 6.169 ($R^2=0.9425$) when applied fused superphosphate fertilizer, and y = 0.0662x - 2.689 ($R^2=0.9315$) when applied LC at the equivalent rates to phosphate input (x: phosphate application rate, kg $ha^{-1}$, y: increment in soil available phosphate content, mg $kg^{-1}$). And from these two equations, the correlation on the phosphate application rate between fused superphosphate fertilizer and LC could be obtained as y = 2.7056x - 52.492 (x: $P_2O_5$ application rate of fused superphosphate, kg $ha^{-1}$, y: $P_2O_5$ application rate of LC, kg $ha^{-1}$). Plant height, number of tillers, nutrients uptake by rice, and rice yield showed higher levels in N 100% and N 150% application plots of chemical fertilizers, while every LC plots exhibited lower values and no significant difference among them. Relative nitrogen fertilization efficiencies of LCs compared to urea was 12.3% for CaC, 8.8 for SwC and 24.6 for ChC, respectively.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.186-192
• /
• 2007

High $J_c\;YBa_2Cu_3O_{7-x}$ superconducting films have been fabricated $LaAlO_3(100)$ substrate by MOD method using dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. Heating rate was varied in order to optimize the calcination heat treatment condition in DCA-MOD method. Coated films were calcined at lower temperature up to $500^{\circ}C$ in flowing humid oxygen atmosphere. The heating rate was calcined from $13.3^{\circ}C/min\;to\;0.28^{\circ}C/min$. Conversion heat treatment was performed $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. Surface and cross sectional SEM microstructures showed that particle sizes were increased with heating rate at a calcination step. The amount of pores was increased with heating rate in the calcined films. Dense microstructure and sharp texture were developed in an YBCO films after conversion heat treatment. A high critical current density (Jc) of $1.26MA/cm^2$ (@77 K and self-field) was obtained for the YBCO film which was prepared with a heating rate of $0.28^{\circ}C/min$.

• Journal of Welding and Joining
• /
• v.28 no.5
• /
• pp.45-50
• /
• 2010

The fatigue crack growth characteristics of base metal and weld joint of 9% Ni steel for LNG storage tank was carried out using CT specimen at room temperature and $-162^{\circ}C$. Fatigue crack growth rate of base and weld metals at RT and $-162^{\circ}C$ was coincided with a single line independent of the change of stress ratio and temperature. In the region of lower stress intensity factor range, fatigue crack growth rate at $-162^{\circ}C$ was slower than that at RT, and the slop of fatigue crack growth rate at $-162^{\circ}C$ increased sharply with propagating of fatigue crack, fatigue crack growth rate at RT and $-162^{\circ}C$ was intersected near the region of $2{\times}10-4\;mm$/cycle, and after the intersection region, fatigue crack growth rate at $-162^{\circ}C$ was faster than that at RT. The micro-fracture mechanism using SEM shows the ductile striation in the stable crack growth region. Also the defects of weld specimen after fatigue testing were detected using the A scan of ultrasonic apparatus.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.7B
• /
• pp.528-537
• /
• 2008

This paper proposes a dynamic job distribution algorithm in a hybrid NoC structure which can improve system network performance by reducing deadlock and packet drop rate for various multimedia applications. The proposed job distribution algorithm schedules every job to the sub-cluster where packet drop rate can be minimized for each multimedia application program. The proposed Job distribution algorithm and network topology targets multimedia applications frequently used in modern embedded systems, such as MPEG4 and MP3 decoder, GPS positioning system, and OFDM demodulator. Experimental results show that packet drop rate was reduced by about 13.0%, and chip area was increased by about 2.7% compared to the APSRA algorithm. When compared to the XY algorithm popularly used for benchmarking, the packet drop rate was reduced by about 23.9%, while chip area was increased by about 3.0%.

• Korean Journal of Plant Resources
• /
• v.18 no.3
• /
• pp.497-504
• /
• 2005

This experiment was conducted to improve germination rate of the seed treated duration of storage and $GA_3$ in Celosia argentea. With the seed directly after harvest, as increasing concentration of $GA_3$, ranged from 50ppm to 200ppm, and dipping hour, ranged from 6 to 24 hour, the rate of germination was also increased. The germination of seed dipping in 200ppm $GA_3$ for 24 hours was the highest with $52\%$ compared to the control with $12\%$. As increasing storage duration in $22{\pm}2^{\circ}C$, ranged from 2 weeks to 12 weeks, the rate of germination was also increased showing $84\%$ at 12 week. However, the rate of germination was not increased with the storage of $5^{\circ}C,\;0^{\circ}C,\;and\;-70^{\circ}C$. With the seed storage 16 weeks in $22{\pm}2^{\circ}C$ after harvest, the rate of germination was $84\%$. The rate of germination was increased $94\%\;to\;99\%$ by the $GA_3$ concentration, ranged from 50ppm to 400ppm, and dipping hour, ranged from 6 to 24 hour. The germination was finished 4 days after sowing.