• Journal of Ocean Engineering and Technology
• /
• v.12 no.3 s.29
• /
• pp.31-41
• /
• 1998

Single fiber fragmentation technique was used to evaluate the change of interfacial properties by degradation of fiber tensile strength in the fiber reinforced composites. The influences of fiber tensile strength on the interfacial properties have been evaluated by the fragmentation specimens(weak fiber samples) of glass fiber/epoxy resin that was made using the pre-degraded glass fiber in distilled water at $80^{circ}C$ for specified periods. The effects of the immersion time on the interfacial properties in the distilled water at $80^{circ}C$ also have been evaluated by the fragmentation specimens(original fiber samples) of glass fiber/epoxy resin that was made using the received glass fiber. As the result, the tensile strength of glass fiber was decreased with the increasing of the treatment time in the distilled water at $80^{circ}C$ and the interfacial shear strength was independent of the change of the glass fiber strength in the single fiber fragmentation test. But in the durability test using the single fiber fragmentation specimen, interfacial shear strength decreased with the increasing of the immersion time in distilled water ar $80^{circ}C$. And it turned out that the evaluating of interfacial shear strength using original fiber tensile strength was valuable in the durability test for the water environment by the single fiber fragmentation technique.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.111-115
• /
• 2005

Recently, natural fibers draw much interests in composite industry due to low cost, light weight, and environment-friendly characteristics compared with glass fibers. In this study, mechanical properties were evaluated for two extreme cases of jute fiber orientations, i.e. the unidirectional yarn composites and the felt fabric composites. Samples of jute fiber composites were fabricated by RTM process using epoxy resin, and tensile, compression, and shear tests were conducted. As can be expected, unidirectional fiber specimens in longitudinal direction showed the highest strength and modulus. Compared with glass/epoxy composites of the similar fabric architecture and fiber volume fraction, the tensile strength and modulus of jute felt/epoxy composites reached only 40% and 50% levels. However, the specific tensile strength and modulus increased to 80% and 90% of the glass/epoxy composites. The main reason for the poor mechanical properties of jute composites is associated with the weak interfacial bonding between fiber and matrix. The effect of surface treatment of jute fibers on the interfacial bonding will be examined in the future work.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.323-323
• /
• 2007

Influence of $La_2O_3$ addition to $CaO-B_2O_3$-based glass on the water leaching resistance of the glass was first investigated. The optimized $La_2O_3-CaO-B_2O_3$(LCB) glass was ball milled for varying time, followed by mixing with $Al_2O_3$ crystalline phase to form $Al_2O_3$-LCB glass composites at $875^{\circ}C$ for 1h. Microwave dielectric properties of the composites were investigated as a function of the ball milling time of the LCB glass. Dielectric constant and quality factor of the composites were 6.31 and 13856 GHz, respectively, when the LCB glass was ball milled for 2h prior to mixing with $Al_2O_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.324-324
• /
• 2007

Influence of $La_2O_3$ addition to $ZnO-B_2O_3$-based glass on the water leaching resistance of the glass was first investigated. The optimized $La_2O_3-ZnO-B_2O_3$ (LZB) glass was ball milled for varying time, followed by mixing with $Al_2O_3$ crystalline phase to form $Al_2O_3$-LZB glass composites at $875^{\circ}C$ for lh. Microwave dielectric properties of the composites were investigated as a function of the ball milling time of the LZB glass. Dielectric constant and quality factor of the composites were 6.01 and 11676 GHz, respectively, when the LZB glass was ball milled for 2h prior to mixing with $Al_2O_3$.

• The Korean Journal of Ceramics
• /
• v.1 no.2
• /
• pp.96-100
• /
• 1995

Recently, alumina/glass composites have been applied as a substrate material for hybrid IC and LSI multi-chip packaging. In this study, the characterization of sodium borosilicate glasses containing NaF and $AlF_3$ and the preparation of the resulted glass/alumina composites have been examined and the effect of the addition of fluorides on the thermal. and dielectric properties of the sintered composites have been studied. The sintering temperature of specimens was lowered by about 100-$150^{\circ}C$ by the addition of fluorine compared with the specimens without fluorine. The specimens containing fluorine showed slightly lower dielectric constants than those of the specimens without fluorine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.3
• /
• pp.295-305
• /
• 1992

The critical strain energy release rate and the failure mechanisms of glass-carbon epoxy resin hybrid composites are investigated in the temperature range of the ambient temperature to 8$0^{\circ}C$. The direction of laminates and the volume fraction are [(+45, -45, 0, 0) sub(2) ] sub(s), 50%, respectively. The major failure mechanisms of these composites are studied using the scanning electron microscope for the fracture surface. Results are summarized as follows: 1) The critical strain energy release rate shows a maximum at ambient temperature and it tends to decrease as temperature goes up. 2) The critical strain energy release rate increases as the content of glass increases, and especially shows dramatic increase for the high glass fiber content specimens. 3) Major failure mechanisms can be classfied such as localized shear yielding, fiber-matrix debonding, matrix micro-cracking, and fiber pull-out and/or delamination.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.626-633
• /
• 1998

For the fabrication of low temperature cofirable glass/ceramic with high dielectric constant, crystallizing glass [$SiO_2-TiO_2-RO (RO:BaO, CaO:SrO)$] was formed. The glass/ceramic composites were made by mixing this glass and alumina ceramic as filler, and its characteristics was investigated. With this glass compositon, it was possible to fabricate the glass which could be crystallized under $900^{\circ}C$. And it was found that the crystallizing temperature was changed in accordance with the composition of RO in glass. By adding $Bi_2O_3$ as flux, using $Al_2O_3$ as filler and sintering at $860^{\circ}C$, low temperature cofirable glass/ceramic with high dielectric constant was fabricated. The density of that composites was 3.96 g/$\textrm{cm}^3$, dielectric constant was 17 and Q. f was 600.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.281-281
• /
• 2007

Low Temperature Co-fired Ceramic (LTCC) technology has been used in electronic device for various functions. LTCC technology is to fire dielectric ceramic and a conductive electrode such as Ag or Cu thick film below the temperature of $900^{\circ}C$ simultaneously. The glass-ceramic has been widely used for LTCC materials due to its low sintering temperature, high mechanical properties and low dielectric constants. To obtain the high strength, addition of filler, the microstructure should have various crystals and low pores in a composite. In this study, two glass frits were mixed with different alumina size(0.5, 2, 3.7um) and sintered at the range of $850{\sim}950^{\circ}C$. The microstructure, crystal phases, thermal and mechanical properties of the composites were investigated using FE-SEM, XRD, TG-DTA, Dilatomer. When the particle size of $Al_2O_3$ filler increased, the starting temperatures for the densification of the sintered bodies, onset point of crystallization, peak crystallization temperature in the glass-ceramic composites decreased gradually. After sintered at $900^{\circ}C$, the glass frits were crystallized as $CaAl_2Si_2O_8\;and\;CaMgSi_2O_6$. The purpose of our study is to understand the relationship between the $Al_2O_3$ particle size and thermal properties in composites.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.279-279
• /
• 2007

Synthesis and dielectric properties of glass-ceramic composites with zinc borosilicate glass(here after ZBS glass) were investigated as functions of $ZnAl_2O_4$ phase synthesis method, glass addition (50~60 vol%) and sintering temperature ($600{\sim}950^{\circ}C$ for 2 hrs). The 50 vol% ZBS glass-$Al_2O_3$ and 60 vol% ZBS glass-$ZnAl_2O_4$ ensured successful sintering below $900^{\circ}C$. But the composition of 100-x-y vol% ZBS glass-x vol% $Al_2O_3-y$ vol% ZnO exhibited poor sinterability below $900^{\circ}C$ and the swelling phenomenon occurred in this composite with the large amount of ZBS glass. The sintering behavior of Glass-ceramic composites was affected by the crystallization of $ZnAl_2O_4$ which was formed by the reaction between ZBS glass and $Al_2O_3$. Dielectric constant (${\varepsilon}_r$), $Q{\times}f$ value and temperature coefficient of resonant frequency (${\tau}_f$) of the composite with 50 and 60 vol% ZBS glass contents demonstrated $ZBS-Al_2O_3({\varepsilon}_r=5.7)$, $ZBS-ZnAl_2O_4({\varepsilon}_r=5.8)$ which is applicable to substrate requiring an low dielectric properties.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.314-319
• /
• 2004

Many of researches regarding mechanical properties of composite materials are associated with humid environment and temperature. Especially the temperature is a very important factor influencing the design of thermoplastic composites. However, the effect of temperature on impact behavior of reinforced composites have not yet been fully explored. An approach which predicts critical fracture toughness GIC was performed by the impact test in this work The main goal of this work is to study effects of temperature in the impact test with glass fiber/polypropylene(GF/pp) composites. The critical fracture energy and failure mechanisms of GF/PP composites are investigated in the temperature range of $60^{\circ}C\;to\;-50^{\circ}C$ by impact test. The critical fracture energy shows a maximum at ambient temperature and it tends to decrease as temperature goes up or goes down. Major failure mechanisms can be classified such as fiber matrix debonding, fiber pull-out and/or delamination and matrix deformation.