• Bulletin of the Korean Space Science Society
• /
• 2002.05b
• /
• pp.34.1-34
• /
• 2002

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.6
• /
• pp.556-563
• /
• 2007

The current trend of low cost ultra-small satellites is to utilize Commercial Off the Shelf (COTS) parts to save cost, and accordingly, Command and Data Handling (C&DH) that operates the satellite and collects/processes the data is also designed and developed around commercial controllers. However, functionalities of commercial controllers are limited according to the specs outlined by the manufacturer. In order for the commercial controllers to be used for satellites where variety of interfaces is required, a separate interface circuit is required. Therefore, a Multi Digital Data Control System (MDDCS) using Field Programmable Gate Array (FPGA) has been developed in order to expand multiple digital interfaces that are not supported by the commercial controller, and also to compensate for SEU. This has been implemented on Actel A3P1000 using Very High Speed Integrated Circuits Hardware Description Language (VHDL).

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.1
• /
• pp.17-22
• /
• 2010

The enhancement of adhesion for Cr film on polycarbonate (PC) substrate with electron irradiation treatment was considered. The electron treatment changes the contact angle of the PC substrates. As increase the electron energy from 300 eV to 900 eV, the contact angle decreases from $90^{\circ}$ to $60^{\circ}C$. It is supposed that electron treatment changes the chemical property of PC substrate into hydrophilic one. The micro surface roughness was also affected by electron treatment. The PC substrates irradiated with intense electron beam of 900 eV show the rougher surface than those of other PC substrates. Cr thin films deposited on the PC substrate treated with electron irradiation at 900 eV show the higher adhesion than that of the Cr thin film deposited untreated bare PC substrates.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.171-177
• /
• 2011

Tensile tests were conducted at low temperatures for the steel materials which are used for outer shell of the vessels making transit through the polar regions. The selected steel materials were GL-DH32, GL-DH36 and GL-EH36. In comparison with the results at room temperature, the yield stress increases approximately by 10 to 13 percent at $-30^{\circ}C$ and by 13 to 19 percent at $-50^{\circ}C$ while the tensile strength increases about by 9 percent at $-30^{\circ}C$ and 11 to 14 percent at $-50^{\circ}C$. To obtain true stress-true strain, i.e. correct plastic hardening characteristics, Bridgman's(1952) necking correction formula was introduced taking triaxial state of stresses after onset of diffuse necking into consideration. Photographs of fractured surfaces were taken by using Scanning Electron Microscope immedately after tensile tests completed and one for GL-EH36 has been presented in this paper.

• Journal of Plant Biotechnology
• /
• v.49 no.1
• /
• pp.74-81
• /
• 2022

Brassica napus, an oil crop that produces rapeseed oil, is an allotetraploid (AACC, 2n = 38) produced by natural hybridization between B. rapa and B. oleracea. In this study, microspore was cultured using the F₁ developed from a cross between 'EMS26' line with high oleic acid content and 'J8634-B-30' lines. The flower bud size showing the nuclear development at the late uninucleate and binucleate stage with high embryogenesis rate was 2.6 ~ 3.5 mm. Microspores were cultured using only this size and after then most microspore embryo developed into secondary embryos and then regeneration plants obtained from the developed multilobe. The analysis of the ploidy of the plants revealed that 66.7% and 27.8% of the total lines were tetraploids and octoploids, respectively. The sizes of stomatal cells in tetraploids, octoploids, and diploids were 25.5, 35.6, and 19.9 ㎛, respectively, indicating that ploidy level was positively correlated with cell size. Furthermore, 62 tetraploid doubled haploid (DH) lines were selected. The average oleic acid (C18:1) and linolenic acid (C18:3) concentrations of DH were 72.3% and 6.2%, respectively. Oleic acid and linolenic acid concentrations exceeded the two parental values in 5 and 14 DH lines, respectively, suggesting that these two fatty acids had transgressive segregation. Therefore, the DH population can be utilized for the biosynthesis of unsaturated fatty acids in rapeseed and related genes. It can also be used as a breeding material for varieties with high oleic acid concentrations.

• Corrosion Science and Technology
• /
• v.14 no.3
• /
• pp.113-119
• /
• 2015

Alloy 82/182 weld metals had been extensively used in joining the components of the PWR primary system. Unfortunately, there have been a number of incidents of cracking caused by PWSCC in Alloy 82/182 welds during the operation of PWR worldwide. To mitigate PWSCC, optimization of water-chemistry conditions, especially dissolved hydrogen (DH) and Zn contents, is considered as the most promising and effective remedial method. In this study, the PWSCC behaviours of Alloy 182 weld were investigated in simulated PWR environments with various DH content. Both in-situ and ex-situ oxide characterizations as well as PWSCC initiation tests were performed. The results showed that PWSCC crack initiation time was shortest in PWR water (DH: 30cc/kg). Also, high stress reduced crack initiation time. Oxide layer showed multi-layered structures consisted of the outer needle-like Ni-rich oxide layer, Fe-rich crystalline oxide, and inner Cr-rich inner oxide layers, which was not altered by the level of applied stress. To analyse the multi-layer structure of oxides, EIS measurement were fitted into an equivalent circuit model. Further analyses including TEM and EDS are underway to verify appropriateness of the equivalent circuit model.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.6
• /
• pp.1110-1116
• /
• 1998

To determine the optimum conditions for the enzymic hydrolysis against wheat gluten of high con centrations (6~14%, w/w, protein), a hydrolysis system combining weak acid pretreatment and enzymic hydrolysis was investigated. Alcalase showed the highest DH(degree of hydrolysis) of the tested proteases. After hydrolysis by alcalase, subsequently peptidases were applied for the better DH of the wheat gluten hydrolyzate. Peptidase NP2 showed the highest DH of the tested peptidases, but flavour zyme was shown for the lowest bitter taste of the resulting hydrolyzate. In order to minimize aggregation or gelling at higher initial substrate concentration during heat treatment, wheat gluten suspension was pretreated with possibly low concentrations of hydrochloric acid at 105oC for 1 hour, and then enzy matically hydrolysed with alcalase and subsequently with flavourzyme. Each required minimum concen tration of hydrochloric acid in the wheat gluten suspension of 6, 8, 10, 12, and 14%(w/w, protein) was 0.10, 0.15, 0.20, 0.225, and 0.275N, respectively. After the subsequent enzymic treatment by alcalase and peptidase NP2 for 24 hrs, the nitrogen solubility in the final wheat gluten hydrolysates was increased to 94.9, 86.4, 85.3, 89.3 and 95.0%, and their amino nitrogen content was increased to 2.87, 5.68, 7.34, 9.71 and 12.50mg/m, respectively.

• Korean Journal of Microbiology
• /
• v.28 no.1
• /
• pp.27-34
• /
• 1990

Two macrolide-lincosamide-streptogramin B (MLS) antibiotic resistance genes, one expressed inducibly and the other expressed constitutively were recognized from a single Staphylococcus aureus DH1 strain. The inducible MLS resistance gene was isolated and cloned from the R-plasmid pDE1(7.4kb) and the constitutive gene was from chromosomal DNA. Base sequence of the inducible MLS resistance gene (1.2kb) was determined and found as same that of pE194. The restriction map of the cloned constitutive MLS resistance gene was compared with that of the inducible gene. Two genes have same restriction map except leader region. In the constitutive gene there is no leader region which is doing major role in inducible expression.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.6
• /
• pp.337-345
• /
• 2011

The objective of this work is to investigate the effect of chemical enhancer and current on the flux of donepezil hydrochloride (DH) through skin. Ethanol and N-methyl pyrrolidone (NMP) were used as chemical enhancers in combination with iontophoresis. We also have studied the effect of pH on flux and evaluated the role of electroosmosis. In vitro flux study was performed at $33^{\circ}C$, using side-by-side diffusion cell and full thickness hairless mouse skin. Passive flux of DH without enhancer was very small. As the concentration of enhancer increased, passive flux increased. After current application, flux increased markedly and the time to reach maximum decreased. Without enhancer, maximum flux was about 50 fold larger than that obtained without current. These results indicate that electromigration is playing a major role for the transport. As the enhancer concentration increased, flux also increased. NMP and ethanol increased not only the passive delivery, but also the iontophoretic delivery. Flux results indicate that ethanol has better ability than NMP in enhancing the transport of DH. The magnitudes of increase in flux by these enhancers indicate that there is a large synergistic effect in flux enhancement. Flux results from pH study showed that electroosmotic flow is reversed at low pH and the flux is hindered. These results provided some information on the flux enhancing ability of ethanol and NMP in combination with iontophoresis. The data also provided some mechanistic insights into the role of electromigration and electroosmosis on flux through skin.

• KSBB Journal
• /
• v.17 no.6
• /
• pp.571-576
• /
• 2002

Recombinant E. coli DH5 ${\alpha}$/pSB311 was made by cloning the genes encoding bacterial luciferase and aldehyde substrate proteins from Photohabdus luminescense, to complement defects of Lumistox, which is normally used in bioassays to monitor toxic substances in water environmental systems. The conditions for stable light production by the recombinant strains were investigated with respect to cell growth stage, cell number, and buffer conditions. The optimum growth stage was a middle-exponential stage with an OD$_{660nm}$ value of 0.6-0.7. ADout 10$^{6}$-10$^{7}$ cells per test tube was optimum for stable light emission. The effect of buffer was not significant if an optimum viable cell number was maintained. The bioluminescence of the recombinant E. coli harboring the lux operon of Photohabdus luminescense was not affected by temperature, while the bioluminescence of Lumistox was temperature sensitive. The recombinant E. coli was more sensitive to heavy metals (Cd, Cu, Hg, Zn) than Lumistox, because it does not require high concentrations of NaCl in the buffer.