• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1747-1751
• /
• 2003

The paper shows properties such as vickers hardness, yielding and ultimate stresses for the weld zone of the butt and the lap jointed specimens, and compare maximum loads, stress-strain curves, deformation appearance after guided bending test and fracture appearance for butt and lap jointed specimens. The research in this experiment also shows the weldability of the butt joint specimen is better than that of the lap joint specimen using FSW with $2mm^{t}$ aluminum alloy sheet in milling machine.

• 대한기계학회논문집A
• /
• 제30권2호
• /
• pp.187-193
• /
• 2006

The butt and the lap welding by friction stir welding performs with $2mm^t$ 1050 aluminum alloy sheet. This paper shows behaviors of property such as vickers hardness, yielding and ultimate stresses, and macro structures for weld zone cross section of the butt and the lap jointed specimens. It is also carried out making comparison with maximum loads, stress-strain diagrams, and deformation after the guided bending test and fracture behaviors between the butt and the lap jointed specimens. It is found that the weldability of the butt jointed specimen is better than that of the lap jointed specimen.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.53-64
• /
• 2012

Deep and narrow welds can be produced by laser welding at high welding speeds with a narrow heat-affected zone (HAZ) and little distortion of the workpiece. This study aims to evaluate the usefulness of laser welding at automobile component manufacture. Microstructure observation, hardness test, tensile test and fatigue life test are performed by using the fiber laser welded SPFC590 steel sheets which is used widely in the manufacture of automotive seat frame. Three kinds of specimens are only a SPFC590 steel plate, quasi-butt joint plate and lap joint plate by laser welding. The following results that will be helpful to understand the static strength, fatigue crack initiation and growth mechanism were obtained. (1) The tensile strength of quasi butt joint specimens nearly equal to base metal specimens, but lap joint specimens fractured in shear area of weld metal. (2) The fatigue strength of quasi-butt joint specimen was approximately 8 percent lower than that of the base metal specimens. Furthermore, the lap joint specimens were less than 86 percent of the base metal specimens. (3) The lap joint fatigue specimens fractured at shear area in high level stress amplitude, while fractured at normal area in low level stress amplitude. From these results, the applicability of the laser welding to the automobile component is discussed.

• 한국항공우주학회지
• /
• 제31권1호
• /
• pp.8-17
• /
• 2003

항공기 주구조에서 맞대기중첩연결(Butt Lap Joint) 구조는 저속균열성장 개념의 손상허용설계를 한다. 이러한 연결부 구조는 볼트나 리벳 구멍 가장자리의 부재간 접촉면에서 프레팅에 의한 피로균열이 발생되어 다지점 균열성장 거동을 하는 경우가 많다. 본 연구에서는 초기 모서리균열을 내재한 볼트연결 맞대기중첩연결 구조시편에 프레팅 조건을 달리하여 비행하중스펙트럼 하에서 피로균열 성장거동을 실험적으로 분석하고 잔여강도를 비교하여 프레팅이 균열성장과 손상허용성에 미치는 영향을 고찰하였다. 또한 기존의 응력강도식으로 모서리균열의 성장패턴을 예측하고 실험결과와 비교 분석하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.217-217
• /
• 2009

In this study, the effect of bending strain on the transport property and critical current of lap and butt-jointed BSCCO tapes have been investigated. The samples were joined using a mechanically controlled jointing procedure. In order to ensure a uniform pressure application at the joint part, a single point contact has been devised and also to achieve a uniform thickness at the joint interface.

• 해양환경안전학회지
• /
• 제21권6호
• /
• pp.778-783
• /
• 2015

본 연구는 해상에서의 안전사고의 경감과 국민의 생명을 보호하기 위한 목적으로 자체 연구를 수행하여 FRP의 수리공법인 Butt Joint, Lap Joint, V-Scarf Joint(12t, 16t, 20t), X-Scarf Joint(12t 16t, 20t)의 인장강도와 굽힘강도를 통해 이음방식에 따른 구조강도 특성을 실험하였다. 이음 방법에 따른 인장강도와 굽힘강도의 시험편을 종합 분석한 결과, 인장강도의 강도와 굽힘강도의 그래프 패턴은 비슷한 양상으로 증가와 감소를 하였으며, 인장강도와 굽힘강도 모두 X-Scarf-Butt Joint-V-Scarf-Lap Joint 순으로 강도가 우수하였다. 인장강도는 강도특성이 가장 우수한 X-Scarf라 하더라도 Basic Material의 57% 수준의 강도를 나타내었고 굽힘강도는 X-Scarf가 Basic Material의 77% 수준의 강도를 나타내었다. 종합적으로 Over-Lay 구분을 포함하여 X-Scarf 12t 이음이 인장강도, 굽힘강도 특성이 우수하였으며 Lap Joint가 가장 좋지 않았다. Scarf 이음시 Taper 길이에 따른 강도의 차이는 V-Scarf 이음은 Taper의 길이가 가장 큰 20t가 인장강도, 굽힘강도 특성이 우수한 반면 X-Scarf 이음은 Taper의 길이가 가장 짧은 12t가 인장강도, 굽힘강도 특성이 우수하여 상반되는 결과를 나타내었다. 선박에는 많은 Stress가 작용하여 시험편만을 가지고 실험한 본 연구와 직접적인 비교는 힘들지만, 재료의 가장 기본 특성을 인장강도와 굽힘강도 시험을 통해 확인할 수 있다. FRP 국부적인 수리 방법인 Butt Joint, Lap Joint, V-Scarf, X-Scarf 4가지의 이음방법에 따른 시험값과 모재 대비 감소되는 비율을 제시하였고 추가적으로 V-Scarf와 X-Scarf의 Taper 길이별 특성을 12t, 16t, 20t로 구분한 결과값을 제시함으로써 수리 현장에서의 위치별 특성에 맞는 수리 방법의 응용이 가능하도록 하였다.

• Journal of Welding and Joining
• /
• 제20권2호
• /
• pp.95-101
• /
• 2002

After high power lasers are avaliable in the commercial market, the number of applications of the laser welding has been increased in manufacturing industries. Although the tailored blank laser welding of butt jointed steel sheets is well known recently in the automotive industries, the lap joint laser welding is a new technology to the automotive manufacturing people as well as the design people. But the deep penetration laser welding seems to be preferred to the partial penetration welding for the lap joint welding in the automotive manufacturers because the partial penetration is a serious deflect for the butt joint. In this study, the feasibility of partial penetration welding fur the lap joint $CO_2$ laser welding was studied fur the 1mm thick 390MPa high strength steel sheets for automotive bodies. The process window of the lap joint partial penetration welding was obtained from experiments with the gap size and the welding speed as process parameters. The partial penetration welding was found excellent on the basis of the tensile shear strength and sectional geometry. The bead width, input energy Per volume, tensile-shear strength, deformation energy and the sectional geometries after tensile-shear tests of partial penetration welded specimens are compared with those of full penetration welded specimens with a series of gaps and welding speeds.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.62-73
• /
• 2005

The objects of this research are to establish the criteria of peel occurrence considering the shape of bond terminus and to compare the strength properties of adhesive joint of different three type such as butt joint, T-shape, and single lap Joints. The criteria of peel occurrence at the bond terminus was suggested. Peel loads of three type adhesive joint (butt Joint, T-shape specimen, single lap joint) were determined from tensile tests. Principal stress distributions of these joints were determined from finite element method analysis. Then, peel occurrence was estimated with stress singularity factor$(K_{prin})$ when the terminus shape was square, with average principal stress when the terminus shape was rounded. The conclusions are summarized as follows; (1) In the non-filleted model(e.g., butt joint, T-shape specimen), principal stress shows singularity at the bond terminus, intensity of stress(principal stress) singularity $(K_{prin})$ can use as the criteria of peel occurrence at the bond terminus. (2) In the filleted model(e.g., single lap joint), principal stress has not affected singularity at the bond terminus. Average principal stress$(K_{av})$ can use as the criteria of peel occurrence at the bond terminus.

• Journal of the Korean Wood Science and Technology
• /
• 제49권2호
• /
• pp.107-121
• /
• 2021

본 연구에서는 층재 수종과 길이방향의 합판 접합방식과 접합부의 접착제 도포 여부에 따른 휨 성능 및 파괴 양상 분석을 통하여 합판을 코어로 사용한 CLT에 적합한 합판의 접합 방식을 최적화 하고자 하였다. 더글라스 퍼 층재의 경우 길이방향 접합에 의해 휨탄성계수 약 11.5% 감소, 휨강도는 접착제 도포 및 접합방식에 따라 증가 또는 감소하였다. 접착제 미도포 butt joint, 접착제 도포 half lap joint, butt joint 조건이 최적조건으로 도출 되었다. 낙엽송 층재의 경우 길이방향 접합에 의해 휨강도는 약 15%, 휨탄성계수는 약 40% 감소하였으며 접합방식에 따른 차이를 나타내지 않았다. half lab joint와 tongue & groove joint 사용 시 합판 층의 접합부에서 휨에 파괴를 1차적으로 방지해줌으로써 중층의 층재로 전달되는 하중을 감소시켜 주는 것으로 판단된다. 본 연구 결과를 통해 Ply-lam CLT 제조과정에서 낙엽송 층재를 사용하는 경우 접합방법에 따른 차이를 나타내지 않았으며 더글라스퍼 층재를 사용할 경우 butt joint와 half lap 접합 방식이 적합할 것으로 판단된다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.253-255
• /
• 2002

Since a butt Joint is smaller than a lap type joint, it is expected to have smaller AC losses. The butt joint is produced by the diffusion bonding of the contacting surface under pressured and heated condition. It is important to find robust joining conditions, because butt joint has small contact area and has the shape by which the quality of bonding is hard to be checked. In this research, the loading pressure is considered as the joining parameter to find optimum joining condition. The DC resistance of the joint may be changed by the surface pressure during joining process, because the superconducting strands near the contact surface are failed by large plastic deformation. The range from 10 MPa to 18 MPa is expected optimum surface pressure in the conditions of 1 hour heating time and $750^{\circ}C$ temperature in the vacuum furnace.