• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.10
• /
• pp.914-921
• /
• 2005

In this study, the 1/20 reduced-scale experiment using Froude scaling were conducted to investigate the effect of longitudinal ventilation velocity on the burning rate in tunnel fires. The methanol pool fires with heat release rate ranging from 2.02 kW to 6.15 kW and the n-heptane pool fires with heat release rate ranging from 2.23 kW to 15.6 kW were used. The burning rate of fuel was obtained by measuring the fuel mass at the load cell. The temperature distributions were observed by K-type thermocouples in order to investigate smoke movement. The ventilation velocity in the tested tunnel was controlled by inverter of the wind tunnel. In methanol pool fire, the increase in ventilation velocity reduces the burning rate. On the contrary in n-heptane pool fire, the increase in ventilation velocity induces large burning rate. The reason for above conflicting phenomena lies on the difference of burning rate. In methanol pool fire, the cooling effect outweighs the supply effect of oxygen to fire plume, and in n-heptane pool vice versa.

• Journal of Acupuncture Research
• /
• v.29 no.2
• /
• pp.1-8
• /
• 2012

Objectives : This study was performed to compare the effects between Mountain-burning fire method and Heaven-penetrating cooling method on thermographic change. Materials and Methods : The experiment was conducted to 20 students of College of Oriental Medicine, Woosuk University from July 12, 2011 to July 26, 2011. Acupuncture stimulation was applied at left $Zusanli$($ST_{36}$) with Mountain-burning fire method in A group(n=10) and Heaven-penetrating cooling method in B group (n=10). To estimate thermographic change, temperature of left $Zusanli$($ST_{36}$), $Shuigou$($GV_{26}$), $Zhongwan$($CV_{12}$) were measured by DITI(digital infrared thermographic image) before acupuncture stimulation and 30sec, 10min after needle removal. Results : In A group, the temperature of left $Zusanli$($ST_{36}$), $Shuigou$($GV_{26}$), $Zhongwan$($CV_{12}$) were decreased at 30sec after needle removal, statistically. And the temperature of $Zusanli$($ST_{36}$), $Zhongwan$($CV_{12}$) were decreased at 10min after needle removal, statistically. In B group, the temperature of $Zusanli$($ST_{36}$), $Zhongwan$($CV_{12}$) were decreased at 10min after needle removal, statistically. But, there was no significant difference between two groups on thermographic change, statistically Conclusions : Acupuncture stimulation applied at left $Zusanli$($ST_{36}$) with Mountain-burning fire method has more widespread effects than Heaven-penetrating cooling method. But further studies will be needed such as thermographic change with no stimulation and with more subjects.

• Proceedings of the KOSOMBE Conference
• /
• v.1993 no.11
• /
• pp.128-131
• /
• 1993

In order to get the basic data for the study of the heat stimulation of burning moxa, the pattern of combustion temperature, which is one of the important factors of thermal characteristics, was measured by density of cone moxa along the time procedure. The following results have been obtained 1) The pattern of combustion temperature by moxa burning was classified into input period which means the infiltration of heat into the area and output period which means the radiation of heat from the area. The input period consists of preheating and heating periods, while the output period consists of heat retaining and cooling periods. 2) The pattern of combustion temperature showed the same type or curve, which was not influenced by the moxa weight. However, Its pattern gradient are varied by density. It is considered that the pattern of combution temperature is primarily influenced by the rate of combustion temperature, gradient temperature and duration of combustion.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.11
• /
• pp.1417-1423
• /
• 2004

The thickness of laminar flame and preheat zone was computed from equation with burning velocity and the temperature profile, which is obtained by using premix code of Chemkin program for ethanol-air mixture. The computations were carried out under the unburned gas pressure 0.5bar-30bar and temperature of 300k-700K at 1.0. A difference flame thickness showed between temperature profile and equation with burning velocity. The ratio of flame thickness derived from the equation was about 45∼65% of the temperature profile, and the thickness of preheat zone was about 67.1% of the flame thickness. The flame thickness was decreased by increasing the pressure and temperature, but the effect of pressure is more significant than the effect of temperature on the flame thickness. The flame thickness was predicted by using the following equation. X(mm) = $X_{st}$ (T/300)$^{-0}$.65/(P)$^{-0}$.68/ (0.5bar$\leq$P$\leq$30bar, 300K$\leq$T$\leq$700K)K)

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.102-108
• /
• 2006

On the refutation demanded for a control of various toxic substances. PCBs(poly chlorinated biphenyl) has a fatal poisonous matter in the ecosystem and the environmental pollution as it Is a kind of stable chemical substance. Especially, the gross Product of PCBs is estimated at about one million tonnage all over the world. However it is kept on storing in untreated state, then has a deterioration by the Prolonged storage and a risk of overflowing. Therefore, this research examined the fundamental characteristics of combustion and emission for the target of using the IPA (iso-propyl alcohol) solution as a part of PCBs control. IPA was filled to three kinds of Vessel, i.e. Vessel I, II, and III, and then was investigated as follows combustion shape, flame temperature. mass burning velocity, and PM(Particulate matter). A radial thermometer and a C-A thermocouple measured the flame temperature, and the optical extinction method by using He-Ne laser and the filter weight method used in the PM measurement. As a result, with an increasing of L/S ratio, the flame length become shorter and the burning velocity is more rapid, but the particulate matters is higher. It is supposed that the air flow rate is high on Vessel. and then the combustion is Promoted in the surface area of the upstream zone. The future works plan to investigate the characteristics with an using of the mixing of IPA and PCBs

• Journal of the Korean Society of Safety
• /
• v.19 no.3 s.67
• /
• pp.45-50
• /
• 2004

4-panel of 1m height and 45cm width were fixed on the $40cm{\times}40cm$ bottom plate and the opening of the panel comer was 5cm. Diameter of stainless vessel is loom and its height is 2cm and it located at the center of the bottom plate. 78mL liquid fuel was filled in the vessel and its depth was 1cm. Flame temperature was measured with K type thermocouple, and radiation heat of flame was measured with heat flux meter. Flame height and its behavior was visualized with video camera. and mass burning rate was measured by fuel combustion time. According to the development of fire, flame swirling was begin. From the experiment the mass burning rate was larger and the height of flame was higher than the usual pool fire flame. Flame temperature and heat flux also increased far more than the pool fire. Consequently the swirling air flow through the openings between the panel and thermal buoyance contribute to increase of heat release rate, flame length and mass burning rate.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.819-825
• /
• 2004

The characteristic analysis of cement clinker using light microscope can evaluate not only the quality of cement but also making process. Thus this study analyzed clinkers having different burning conditions by reflective light microscope. As heating and cooling rates is decreased, alite and belite minerals grew and especially cooling rate had an effect on the growth of belite. Futhermore as the retention time in max. temperature got longer by twenty minutes, alite and belite minerals grew more about 5 $\mu\textrm{m}$. In the case of temperature 1400$^{\circ}C$ in max, the size of belite was suitable but alite was not suitable with the size of 10～15 $\mu\textrm{m}$.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.225-233
• /
• 2007

The engineering properties of surface soils in natural terrain are changed due to wildfire. This change of engineering properties induced by wildfire is related to landslides occurrence. To investigate the change of soil properties caused by wildfire, the various soil tests are performed. The soil samples are obtained from the recently burned slopes of Yangyang area, Kangwon Province. The soil samples obtained from the burned slopes are classified into three types depending on the burning grade: the perfect burning grade, the intermediate burning grade, the non-burning grade. As the result of tests, the specific gravity and the dry unit weight of soils obtained from perfect and alternative burning grades are less than those of soils obtained from non-burning grade. It judges that an electronic force, ionic components and of soils are changed and organic matters in soils are burned by wildfire. The permeability of soil obtained from alternative burning grade is the lowest and that of soil obtained from perfect burning grade is the highest. The water-repellent layer is formed on soil surface by wildfire. The water-repellent layer is existed at the area of alternative turning grade, while the layer is not existed at the area of perfect burning grade. The water-repellent layer is collapsed in high temperature more than about $400^{\circ}C$.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.110-119
• /
• 2005

The combustion characteristics of binary component single droplets hanging at the tip of a quartz fiber are studied experimentally at different environmental pressures and temperatures under normal gravity. Normal Heptane and Normal Hexadecane are selected as two fuels with high difference in boiling temperatures. A falling electrical furnace in a high pressure vessel has provided high temperature environment. Nitrogen and air have formed the environment to study evaporation and combustion, respectively. The initial diameter of droplet was ranging from 1.1 to 1.3 mm. The evaporation and combustion processes were recorded by a high speed digital camera. Some characteristics of droplet burning under different environment conditions and different droplet composition have been investigated. Microexplosion of droplet take places under atmospheric pressure. Bubble formation and its consequent result, incomplete droplet disintegration which presents in all binary compositions, do not appear at high pressure. The initiation of combustion, always takes place in the bottom of droplet due to buoyancy effect of relatively cold fuel vapor. Also, the burning of binary droplet produces soot when the pressure is high.

• Journal of Hydrogen and New Energy
• /
• v.15 no.1
• /
• pp.12-22
• /
• 2004

In order to evaluate the potential of partial hydrocarbon substitution to improve the safety of hydrogen use in general and the performance of internal combustion engines in particular, the outward propagation and development of surface cellular instability of spark-ignited spherical premixed flames of mixtures of hydrogen, hydrocarbon, and air were experimentally studied at NTP (normal temperature and pressure) condition in a constant-pressure combustion chamber. With propane being the substituent, the laminar burning velocities, the Markstein lengths, and the propensity of cell formation were experimentally determined, while the laminar burning velocities and the associated flame thicknesses were computed using a recent kinetic mechanism. Results show substantial reduction of laminar burning velocities with propane substitution, and support the potential of propane as a suppressant of both diffusional-thermal and hydrodynamic cellular instabilities in hydrogen-air flames.