• Electronics and Telecommunications Trends
• /
• v.12 no.6 s.48
• /
• pp.131-135
• /
• 1997

본 고는 ATM교환기 고온 상태 동작 특성을 시험하기 위하여 온도 조건, 시험 시간, 시험 절차, 시험 방법, 세부 기준, 판정 기준 등을 정한 것으로, 고온 동작 기준은 한국통신 환경 관리기준 및 품질 표준서-4101을 근거로 하였다. 온도 조건은 평균 $49^{\circ}C$를 유지하되 허용편차는 $1^{\circ}C$내외로 시험되어야 하며, 시험 시간은 온도 상승 및 하강 시간과 장애 발생시 고장 조치 시간 등을 포함하여 최대 72시간을 넘지 않아야 하고, 고온 유지시간은 48시간으로 채택한, ATM 교환기 고온 시험 방법과 기준을 제시하였다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.6
• /
• pp.440-447
• /
• 2001

This study investigate experimentally the effect of in height, thickness, and clearance on the boiling heat transfer. The heat surfaces having copper fin array is tested for pool boiling. The gas-liquid exchange interference is investigated based on fin array clearance. These test results can be applied to the design of tube bundle system. The fin height of 2 mm is found to be effective. Effects of heat transfer promotion reaches the highest level when the fin clearance is 0.5mm. Also, heat flux is increased when the fin thickness is smaller. But0.2 mm fin thickness is highly recommended.

• Journal of Life Science
• /
• v.10 no.2
• /
• pp.157-163
• /
• 2000

One hundred eight strains of Pseudomonas aeruginosa isolated from the patients (sputum, urine, burn skin, stool and blood) of Pusan National University hospital were tested for exonezyme production, antimicrobial susceptibility and serotyping. The results obtained were as follow: In exonezyme production test, 50 strains (46.30%) produced both protease and elastase. Thirty three strains (30.55%) did not produce any exoenzyme, 18 strains (16.67%) produced only protease and 7(6.48%) stains only produced elastase. As the result of antimicrobial susceptibility by the disc diffusion method, most strains were resistant to sulfamethoxazole (96.30%). But the resistant rate against gentamicin and ticarcillin were 47.23% and 46.30% respectively. The resistant rate to other antibiotics were less than 40%. All strains could be serologically typed. Most strains were identified as type Ⅲ: among them, 51 strains were belonged to serotype E. The correlation of serotype and exoenzyme production was not found.

• Nuclear Engineering and Technology
• /
• v.42 no.5
• /
• pp.576-581
• /
• 2010

KAERI (Korea Atomic Energy Research Institute) fabricated MOX (Mixed Oxide) fuel pellets as a cooperation project with PSI (Paul Scherrer Institut) for an irradiation test in the Halden reactor. The MOX pellets were fitted into fuel rods that included instrumentation for measurement in IFE (Institutt for Energiteknikk). The fuel rods were assembled into the test rig and irradiated in the Halden reactor up to 50 MWd/kgHM. The irradiated fuel rods were transported to the IFE, where ceramography was carried out. The fuel rods were cut transversely at the relatively higher burn-up locations and then the radial cross sections were observed. Micrographs were analyzed using an image analysis program and grain sizes along the radial direction were measured by the linear intercept method. Radial cracks in the irradiated MOX were observed that were generally circumferentially closed at the pellet periphery and open in the hot central region. A circumferential crack was formed along the boundary between the dark central and the outer regions. The inner surface of the cladding was covered with an oxide layer. Pu-rich spots were observed in the outer region of the fuel pellets. The spots were surrounded by many small pores and contained some big pores inside. Metallic fission product precipitates were observed mainly in the central region and in the inside of the Pu spots. The average areal fractions of the metallic precipitates at the radial cross section were 0.41% for rod 6 and 0.32% for rod 3. In the periphery, pore density smaller than 2 ${\mu}m$ was higher than that of the other regions. The grain growth occurred from 10 ${\mu}m$ to 12 ${\mu}m$ in the central region of rod 6 during irradiation.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.305-309
• /
• 2007

FTL(Fuel Test Loop) is a facility that confirms performance of nuclear fuel at a similar irradiation condition with that of nuclear power plant. FTL construction work began on August, 2006 and ended on March, 2007. During Construction, ensuring the worker's safety was the top priority and installation of the FTL without hampering the integrity of the HANARO was the next one. The installation works were done successfully overcoming the difficulties such as on the limited space, on the radiation hazard inside the reactor pool, and finally on the shortening of the shut down period of the HANARO. The Commissioning of the FTL is to check the function and the performance of the equipment and the overall system as well. The FTL shall start operation with high burn up test fuels in early 2008 if the commissioning and licensing progress on schedule.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.27-33
• /
• 2008

Natural gas has been considered one of the most promising alternative fuels for transportation because of its abundance as well as its ability to reduce regulated pollutants. We measured emission characteristics of nanoparticles from lean burn H/D(Heavy-Duty) CNG (Compressed Natural Gas) engine equipped with oxidation catalysts. The experiments were carried out to measure the emission and engine performance according to the ESC test cycle. The CO and THC conversion efficiencies on the best catalyst in the ESC test cycle achieved about 91 % and 83 %, respectively. From the measurement by the SMPS, the number of nanoparticles emitted from H/D CNG engine is reduced by about 99 % which is more than that of 2.5 L diesel engine. The particle number concentrations of H/D CNG engine were almost nanoparticles. Nanoparticles smaller than 30 nm emitted from the H/D CNG engine and diesel engine equipped with a CDPF(Catalyzed Diesel Particulate Filter) were quite similar. However, the particles bigger than 30nm from the CNG engine were smaller than the particles from diesel engine equipped with a CDPF. The higher the CNG engine load, the lower the particle number from engine-out, but it increased slightly at full load.

• Journal of the Society of Disaster Information
• /
• v.20 no.3
• /
• pp.519-532
• /
• 2024

Purpose: This study analyze the correlation between elections and wild Fire to provide information necessary for formulating wild fire prevention and response policies. Method: Data of the Forest Service and the Meteorological Administration were used to compare the occurrence and burned area of wild fires in election and non-election years. Statistical significance between the two groups was analyzed with an independent sample t-test, and MANOVA(multivariate analysis of variance) was used to evaluate the effects of temperature and humidity. Result: There was no statistical significance in the occurrence and burn area of wild fires between election and non-election years. However, analysis of the raw data indicated significantly greater damage in election years. MANOVA revealed that election status, temperature, and humidity did not significantly impact the occurrence and burn area of large wild fires. Conclusion: Wild fire occurrence and burned area were higher election years than non-election years, possibly due to election-related social factors. Thus, enhancing wild fire prevention and response policies in election years and considering weather factors and social activites is necessary.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.113-119
• /
• 2013

To develop a new nuclear fuel, it needs to make a test fuel rod and carry out burn-up test in the test loop of a research reactor to check the irradiation characteristics of the nuclear fuel. At that time, several sensors such as thermocouples, LVDTs and SPNDs are needed to be attached in and out of the fuel rod and connect them with instrumentation cables. Then, the instrumentation cables deliver the signals measured by the sensors to the measuring device located outside of the reactor pool. In particular, to install a thermocouple in a fuel rod, it needs to drill off holes on the alumina blocks and sintered $UO_2$ pellets. However, because the hardness of a sintered $UO_2$ pellet is 700 Hv (or HRC 61) and that of an alumina block is 1480 Hv, a special drilling machine which adapts a diamond coated drill bit had developed. In this study, several case experiments have been carried out to find an optimal drilling condition of the drilling machine. And, using the optimal drilling condition, minimum numbers of the holes that a drill bit can drill off are verified.

• Archives of Plastic Surgery
• /
• v.39 no.2
• /
• pp.143-149
• /
• 2012

Background : Axillary osmidrosis is characterized by an unpleasant odor, profuse sweating, and in some instances, staining of clothes that may socially and psychologically impair affected individuals. Various types of surgical procedures have been developed for the treatment of axillary osmidrosis. This study was undertaken to evaluate the effectiveness of subcutaneous pulsed neodymium: yttrium-aluminum-garnet (Nd-YAG) laser treatment for the treatment of axillary osmidrosis. Methods : Twenty-nine patients with axillary osmidrosis were included in this study. Patients were categorized according to the results of an axillary malodor grading system, and a subcutaneous pulsed Nd-YAG laser was applied to all patients. The treatment area for the appropriate distribution of laser energy was determined using the iodine starch test (Minor's test) against a grid pattern composed of $2{\times}2cm$ squares. The endpoint of exposure was 300 to 500 J for each grid, depending on the preoperative evaluation results. The results were evaluated by measurement of axillary malodor both pre- and postoperatively using the grading system and iodine starch test. Results : The average follow-up period was 12.8 months. Nineteen patients had a fair-to-good result and ten patients had poor results. The postoperative Minor's test demonstrated that there were remarkable improvements for patients with mild to moderate symptoms. Complications including superficial second degree burns (n=3) were treated in a conservative manner. A deep second degree burn (n=1) was treated by a surgical procedure. Conclusions : Subcutaneous pulsed Nd-YAG laser has many advantages and is an effective noninvasive treatment for mild to moderate axillary osmidrosis.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.152-164
• /
• 1982

1. In order to make the improvement of plywood quality, this study has been made. The pretreatments applied to the veneers are as follows. a) The soaking treatment of the veneer in 30 percent methanol solution for 24 hours was applied to remove some resinous materials which may cause many stain discolouring on the face of finished plywood. b) The preservative treatment of the veneer in 2 percent malenit solution for 2 to 3 minutes was adopted to make resistance against decay and insect damages. c) The fire retardant treatment of the veneer in 40 percent ammonium phosphate solution for 2 hours was applied to give retardation effect against fire burning. 2. The results summarized in this study are as follows. a) One percent resinous materials was extracted, after the soaking of the veneers in 30 percent diluted methanol. b) No marks of the dirty stains of resinous materials on the face of the treated plywood was shown, although many quite dirty stains on the face of untreated plywood have contrary seen. c) However, the strip shear test strength of the treated plywood was not decreased. It means that there is no difference in the strength between the treated plywood and the untreated plywood. The strength values were 25.08 kg/$cm^2$ and 24.98 kg/$cm^2$, respectively. d) The strip shear test strength of plywood made of the treated veneers in 2 percent malenit solution was not decreased. e) The slight decrease of the strip shear test strength of the treated plywood made of the treated veneer in 40 percent ammonuim phosphate solution was shown. However, the remarkable difference of the fire retardation activities between the treated specimens and the untreated specimens has seen as in Table 10, that is, the fire proofed specimens had taken about 28 seconds to start to burn, while the untreated specimens had taken 15 seconds to reach to burning. This means that the fire retardation effect of the fire proofed plywood was greater than that of the unproofed plywood.