• Journal of Radiation Protection and Research
• /
• v.36 no.4
• /
• pp.174-182
• /
• 2011

With the reactor operation conditions - 4.3 wt% $^{235}U$ initial enrichment, burn-up 55,000 MWd/MTU, average power 34 MW/MTU for three periods burned time for 539.2 days per period and cooling time for 100 hours after shut down, to set up the condition to determine the minimum height (depth) of spent fuel storage pool to shut off the radiation out of the spent fuel storage pool and to store spent fuels safely, the dose rate on the specific position directed to the surface of spent fuel storage pool induced by the neutron and gamma-ray from spent fuels are evaluated. The length of spent fuel is 381 cm, and as the result of evaluation on each position from the top of spent fuel to the surface of spent fuel storage pool, it is difficult for neutrons from spent fuels to pass through the water layer of maximum 219 cm (600 cm from the floor of spent fuel storage pool) and 419 cm (800 cm from the floor of spent fuel storage pool) for gamma-ray. Therefore, neutron and gamma-ray from spent fuels can pass through below 419 cm (800 cm from the floor) water layer directed to the surface of spent fuel storage pool.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.179-189
• /
• 2008

The performance of Lean NOx Trap (LNT) based on the catalysts of Pt/K/Ba/$\gamma-Al_2O_3$ with proprietary washcoat formulation is studied using a bench flow reactor system. To investigate the effect of temperature and gas hourly space velocity (GHSV) on the nitrogen oxides (NOx) trapping capacity as well as NOx breakthrough time and final ratio of $NO_2$ to NO of LNT, series of adsorption isotherms are carried out with simulated exhaust gases of the lean burn engines. Since typical operation of LNT requires periodic regeneration with a short rich excursion, where the stored or trapped NOx is released and subsequently reduced to $N_2$, the effect of the duration of lean and rich phase and type of reductants on the NOx conversion is investigated. NOx storage capacity and breakthrough time obtained from adsorption isotherms shows a volcano-type dependence on the temperature with a maximum NOx storage capacity occurring $350^{\circ}C$ and with a maximum breakthrough time occurring $400^{\circ}C$ at all GHSVs investigated in this study. Also, maximum ratio of $NO_2$ to NO is obtained at $400^{\circ}C$ with a GHSV of $75,000\;hr^{-1}$ Lean/rich cycle of 100 s lean and 5 s rich used with a concentration of 1.33% of $H_2$ and 4% of CO in the rich phase is found to be optimum at operating temperature of $350^{\circ}C$ and a GHSV of $50,000\;hr^{-1}$.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.113-119
• /
• 2013

To develop a new nuclear fuel, it needs to make a test fuel rod and carry out burn-up test in the test loop of a research reactor to check the irradiation characteristics of the nuclear fuel. At that time, several sensors such as thermocouples, LVDTs and SPNDs are needed to be attached in and out of the fuel rod and connect them with instrumentation cables. Then, the instrumentation cables deliver the signals measured by the sensors to the measuring device located outside of the reactor pool. In particular, to install a thermocouple in a fuel rod, it needs to drill off holes on the alumina blocks and sintered $UO_2$ pellets. However, because the hardness of a sintered $UO_2$ pellet is 700 Hv (or HRC 61) and that of an alumina block is 1480 Hv, a special drilling machine which adapts a diamond coated drill bit had developed. In this study, several case experiments have been carried out to find an optimal drilling condition of the drilling machine. And, using the optimal drilling condition, minimum numbers of the holes that a drill bit can drill off are verified.

• Journal of Technologic Dentistry
• /
• v.17 no.1
• /
• pp.10-25
• /
• 1995

The purpose of this study is to get the difference of the castability in the production of partial denture between Precious Metal Alloys and Base Metal Alloys accompanied with the frequency of reuse. As materials for an experiment, we selected Baker-444 and Soo-444 and Soo-sung as Precious Metal Alloys, New Crown and Chrome Cobalt as Base Metal Alloys. And we tired to case all of them seven times. The experimental results were as follows : 1) In the probability of segments, Baker-444 showed 100$\pm$0.00%, Soo-sung 97.24$\pm$1.58%, New Crown 95.63$\pm$4.28%, and Chrome Cobalt 91.03$\pm$7.76%. Consequently, Precious Metal Alloys were decidely superior to Base Metal Alloys in the castability. 2) In the view of the acheived result, burn-out temperature and smocking time had greatly affected the castability. 3) After casting, Precious Metal Alloys were much less than Base Metal Alloys in the quantity of consumption. It made much difference from the the compiled stastics(p<0.01)

• Journal of the Korean Society of Combustion
• /
• v.14 no.3
• /
• pp.16-23
• /
• 2009

It is strongly desired for coal-fired power plants to utilize not only low-rank coals with high moisture contents, but also lowering cost with diversifying fuel sources. In this study, combustion characteristics of low rank coal with high moisture, and standard pulverized coals are experimentally investigated using TGA (Thermogravimetric Analysis) and DTF (drop tube furnace). The coals tested are three kinds of coal with moisture content ranging from 8.32 to 26.82%. The results show that under the air combustion condition, the burn-out time at TGA rises as moisture content increases, and standard pulverized coal with 8.32% moisture content showed the lowest activation energy of 55.73 kJ/mol. In case of the high amount of moisture, the combustion efficiency decreases due to evaporation heat loss, and unburned carbon in ash produced at combustion process in DTF increased. Aslo, initial deformation temperature of slag attached in alumina tube of DTF decreased with lowering the crytallinity of anorthite and augite. To improve the combustion reactivity and efficiency, it is effective to upgrade through drying the high moisture coal to moisture level (less than 10%) of standard pulverized coal.

• Archives of Plastic Surgery
• /
• v.32 no.2
• /
• pp.250-254
• /
• 2005

Burns due to epileptic seizures are commonly deep and usually require operative treatment. The purpose of this study is to identify the characteristics of burned epileptic patients that could lead to the development of preventive programs to reduce the incidence of burn injuries. We analyzed epidemiological data for 34 patients acutely burned due to epileptic seizure admitted retrospectively. There were 15 male and 19 female subjects. The age distribution was from 6 years to 70 years with the mean age of 42.7 years. Seizures usually occurred while carrying out daily domestic chores. Scalding burns were the most common(38.2%) and most burns were above deep second degree(94.1%). The most common seizure type was generalized tonic-clonic, followed by absence and complex partial. The seizure mostly occurred in the morning because the therapeutic blood level of antiepileptic drugs was decreased extremely at that time by stopping drug arbitrarily or taking inadequately. So more frequent follow-ups at the neurology outpatient clinics for epileptics should be strictly reinforced to maintain the adequate therapeutic blood levels of antiepileptic drugs and fire protective implements should be prepared in the house.

• The Korean Journal of Emergency Medical Services
• /
• v.14 no.1
• /
• pp.19-29
• /
• 2010

Purpose : This study was conducted to examine the degree of recognition of safety education and its execution for child-care teachers at daycare center for the disabled children in Jeollanam-do. Ninety six child care teachers filled out the questionnaire and the results were as follows. Results : 1. The possibility of accident prevention by the day care teachers was a little higher in case of nearby education institution. The most appropriate period of safety education was within one month. 2. Majority of child care teachers had received safety and first-aid educations before and the education was done for less than 2 hours. 3. The best educational method was practice-centered education of off-duty time. The contents of first-aid education were bleeding, fall, shock, and burn. 4. The education material and book should be available to the teachers when they need the knowledge. 5. By the annual schedule, safety education should be conducted and provided to the parents. Conclusion : This study suggested that reinforcement of contents related to emergency situation and actual first-aid as well as theory education in the process of parent and teacher education should be conducted on the basis of information of general conditions related to safety and first-aid education at the daycare center for the disabled children.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.44-45
• /
• 2010

We are currently conducting studies on culturing and biocompatibility assessment of various cells such as neural stem cells and induced pluripotent stem cells(IPS cells) on carbon nanotube (CNT), on nerve regeneration electrodes, and on silicon wafers with a focus on developing nerve integrated CNT based bio devices for interfacing with living organisms, in order to develop brain-machine interfaces (BMI). In addition, we are carried out the chemical modification of carbon nanotube (mainly SWCNTs)-based bio-nanosensors by the plasma ion irradiation (plasma activation) method, and provide a characteristic evaluation of a bio-nanosensor using bovine serum albumin (BSA)/anti-BSA binding and oligonucleotide hybridization. On the other hand, the researches in the case of "novel plasma" have been widely conducted in the fields of chemistry, solid physics, and nanomaterial science. From the above-mentioned background, we are conducting basic experiments on direct irradiation of body tissues and cells using a micro-spot atmospheric pressure plasma source. The device is a coaxial structure having a tungsten wire installed inside a glass capillary, and a grounded ring electrode wrapped on the outside. The conditions of plasma generation are as follows: applied voltage: 5-9 kV, frequency: 1-3 kHz, helium (He) gas flow: 1-1.5 L/min, and plasma irradiation time: 1-300 sec. The experiment was conducted by preparing a culture medium containing mouse fibroblasts (NIH3T3) on a culture dish. A culture dish irradiated with plasma was introduced into a $CO_2$-incubator. The small animals used in the experiment involving plasma irradiation into living tissue were rat, rabbit, and pick and are deeply anesthetized with the gas anesthesia. According to the dependency of cell numbers against the plasma irradiation time, when only He gas was flowed, the growth of cells was inhibited as the floatation of cells caused by gas agitation inside the culture was promoted. On the other hand, there was no floatation of cells and healthy growth was observed when plasma was irradiated. Furthermore, in an experiment testing the effects of plasma irradiation on rats that were artificially given burn wounds, no evidence of electric shock injuries was found in the irradiated areas. In fact, the observed evidence of healing and improvements of the burn wounds suggested the presence of healing effects due to the growth factors in the tissues. Therefore, it appears that the interaction due to ion/radicalcollisions causes a substantial effect on the proliferation of growth factors such as epidermal growth factor (EGF), nerve growth factor (NGF), and transforming growth factor (TGF) that are present in the cells.

• Journal of the Korea Society for Simulation
• /
• v.25 no.2
• /
• pp.51-61
• /
• 2016

With high interest in the patient satisfaction of emergency medical services, there is a lot of effort into improving the process of Emergency Department(ED) utilizing the technology of Internet of Things(IoT). In this study, the core technologies of smart ED are examined and a decision support algorithm for medicine tasks is proposed. The proposed algorithm minimizes the decision risks such as task selection accountability, patient complaints, care delays and longer stay time. It can reduce the nurses burnout and improve the patient care with kindness and consideration. Ultimately, patient satisfaction, job satisfaction and professional identity of nurses can be increased. The comparative study was carried out by simulation in terms of the average length of patient stay in a simplified hypothetical ED system. In all the cases, the proposed algorithm was shown to perform substantially better than the other rule.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.2
• /
• pp.141-147
• /
• 2017

The purpose of this study is to develop an inorganic filling adhesive using MKP and borax based on Dead-burn magnesia and fly ash. First, basic experiments was conducted to derive the proper addition rate of MKP. And this experiment was carried out according to addition ratio of borax. The test items are measured for pot life, flexural strength, compressive strength, adhesive strength, tensile strength, ratio of temperature change, ratio of hardening shrinkage, radon gas and formaldehyde emission. As a result, the proper addition rate of phosphate was 35%. The pot time is about 10minutes, 15minutes and 25minutes according to addition rate of borax. The flexural strength and compressive strength were obtained at 12hours for minimum flexural strength of 8.0MPa and minimum compressive strength of 31.0MPa. The tensile strength was the least 4.1MPa, and the ratio of hardening shrinkage was maximum 2.4% and ratio of heat change was maximum - 0.3%, which satisfied all of the quality standards of 'KS F 4923' (epoxy resin for repairing concrete structures). Both Radon gas and formaldehyde emission was not detected.