• Journal of Biomedical Engineering Research
• /
• v.30 no.3
• /
• pp.185-190
• /
• 2009

Biomedical mobile devices for ubiquitous healthcare consist of biomedical sensors and communication terminal. They have two types of configuration. One is the sensor-network type device using wired or wireless communication with intelligent sensors to acquire biomedical data. The other is the sensor embedded type device, where the data can be acquired directly by itself. There are many examples of sensor network type, such as, fall detection sensor, blood glucose sensor, and ECG sensors networked with commercial PDA phone and commercial phone terminal for ubiquitous healthcare. On the other hand, sensor embedded type mounts blood glucose sensor, accelerometer, and etc. on commercial phone. However, to enable true ubiquitous healthcare, motion sensing is essential, because users go around anywhere and their signals should be measured and monitored, when they are affected by the motion. Therefore, in this paper, two biomedical mobile devices with motion monitoring function were addressed. One is sensor-network type with motion monitoring function, which uses Zigbee communication to measure the ECG, PPG and acceleration. The other is sensor-embedded type with motion monitoring function, which also can measure the data and uses the built-in cellular phone network modem for remote connection. These devices are expected to be useful for ubiquitous healthcare in coming aged society in Korea.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.7
• /
• pp.1302-1308
• /
• 2010

In this study, Zigbee Sensor Node to transmit harmful gases CO and $CO_2$ information using wireless communication within the ground and underground structures were developed. Wireless communication protocol was used Zigbee Stack included IEEE 802. 15.4 MAC protocol. For wireless transmission of detected harmful gas signal from ADC of MCU was implemented Zigbee Sensor Node that was developed protocol using Serial-Port-Profile(SPP) here. The proposed Zigbee Sensor Node was verified transmission distance from experiments. Transmission distance was into 90m in experiments. Distance experiments were measured at 10m intervals using sine & pulse wave input signal at indoors. The proposed Route Sensor Node was applied mesh routing protocol. When built up USN(Ubiquitous Sensor Network)using Route Sensor Node, transmission distance was not limited. On the experimental results, harmful gas values between direct measurements and USN measurements were consistent. The semiconductor CO sensor and N-DIR $CO_2$ sensor module as a harmful sensor was used. Therefore, the proposed Zigbee Sensor Node was verified about reliability and validity to build USN for transmission of harmful gas information.

• Journal of Sensor Science and Technology
• /
• v.32 no.2
• /
• pp.105-109
• /
• 2023

In this study, we present a power-efficient driving method for gas sensor systems based on the analysis of input signal characteristics. The analysis of the gas sensor output signal characteristics in the frequency domain shows that most of the signal portions are distributed in a relatively low frequency region when extracting the gas sensor signal, which can lead to further performance improvement of the gas sensor system. Therefore, the proposed gas signal extracting technique changes the operating frequency of the read-out circuit based on the frequency characteristics of the output signal of the gas sensor, resulting in a reduction of power consumption at the whole system level. The proposed sensing technique, which can be applied to a general-purpose commercial gas sensor system, was implemented in a printed circuit board (PCB) to verify its effectiveness at the commercial level.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.4
• /
• pp.437-445
• /
• 1999

Most autonomous mobile robots view only things in front of then, and as a result, they may collide with objects moving from the side or behind. To overcome this problem, an active omni-directional range sensor system has been built that can obtain an omni-directional depth map through the use of a laser conic plane and a conic mirror. In the navigation of the mobile robot, the proposed sensor system produces a laser conic plane by rotating the laser point source at high speed: this creates a two-dimensional depth map, in real time, once an image is captured. The results obtained from experiment show that the proposed sensor system is very efficient, and can be utilized for navigation of mobile robot in an unknown environment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2191-2204
• /
• 1993

A sensor system has been developed to measure the posture(position and orientation) of mobile robots working in industrial environments. The proposed sensor system consists of a CCD camera, retro-reflective landmarks, a strobe unit and an image processing board. The proposed hardware system can be built in economic price compared to commercial vision systems. The system has the capability of measuring the posture of mobile robots within 60 msec when a 386 personal computer is used as the host computer. The experimental results demonstrated a remarkable performance of the proposed sensor system in the posture measurement of mobile robots - the average error in position is less than 3 mm and the average error in orientation is less than 1.5.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.129-134
• /
• 2012

As application-specific requirements for wireless sensor networks emerge, both real-time and reliable communications become major research challenges in wireless sensor networks due to the many constraints on nodes and wireless links. To support these services, several protocols have been proposed. However, since most of them were designed as well as developed for general purpose applications, it is not recommended that they be directly adapted to applications with special requirements. In this paper, we propose a way to extend the current reliable transport protocol to cover a special real-time service, the (m,k)-firm deadline stream, in wireless sensor networks. While the proposed scheme is basically built on the PSFQ protocol for reliability, some features have been newly developed to support the (m,k)-firm stream efficiently. Finally, simulation results are given to demonstrate the feasibility of the proposed scheme in high traffic and with failed links.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.824-827
• /
• 1996

Most autonomous mobile robots view things only in front of them. As a result, they may collide against objects moving from the side or behind. To overcome the problem we have built an Active Omni-directional Range Sensor that can obtain omnidirectional depth data by a laser conic plane and a conic mirror. In the navigation of the mobile robot, the proposed sensor system makes a laser conic plane by rotating the laser point source at high speed and achieves two dimensional depth map, in real time, once an image capture. The experimental results show that the proposed sensor system provides the best potential for navigation of the mobile robot in uncertain environment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.344-348
• /
• 1992

This paper presents a new methodology for on-line tool breakage detection by sensor fusion concept of an acoustic-emission (AE) sensor. A built-in piezoelectric force sensor was used to measure cutting force instead of a tool dynamometer to preserve the machine tool dynamics. he sensor was inserted in the tool turret housing of an NC lathe. FEM analysis was carried out to locate the most sensitive position for the sensor. When a tool is broken, the explicit changes of signals' pattern take place. A burst-type AE signal increases abruptly. Followingly, a cutting force drops significantly. Therefore a burst of AE signal is used as a triggering signal to inspect the following cutting force. Significant drop of cutting force is utilized to detect tool breakage. The algorithm was implemented in a DSP board for in-process tool breakage detection. The proposed monitoring system was capable of a good applicable tool breakage detection.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.3
• /
• pp.339-350
• /
• 2008

A general active fault-tolerant control framework is proposed for nonlinear systems with sensor faults. According to their identifiability, all sensor faults are divided into two classes: identifiable faults and non-identifiable faults. In the healthy case, the control objective is such that all outputs converge to their given set-points. A fault detection and isolation module is firstly built, which can produce an alarm when there is a fault in the system and also tell us which sensor has a fault. If the fault is identifiable, the control objective remains the same as in the healthy case; while if the fault is non-identifiable, the control objective degenerates to be such that only the healthy outputs converge to the set-points. A numerical example is given to illustrate the effectiveness and feasibility of the proposed method and encouraging results have been obtained.

• The Journal of Korea Robotics Society
• /
• v.6 no.1
• /
• pp.42-48
• /
• 2011

It is very important for a mobile robot to recognize and model its environments for navigation. However, the grid map constructed by sonar sensors cannot accurately represent the environment, especially the narrow environment, due to the angular uncertainty of sonar data. Therefore, we propose a map building scheme which combines sonar sensors and IR sensors. The maps built by sonar sensors and IR sensors are combined with different weights which are determined by the degree of translational and rotational motion of a robot. To increase the effectiveness of sensor fusion, we also propose optimal sensor arrangement through various experiments. The experimental results show that the proposed method can represent the environment such as narrow corridor and open door more accurately than conventional sonar sensor-based map building methods.