• Steel and Composite Structures
• /
• 제18권1호
• /
• pp.273-288
• /
• 2015

As one of the most common failure types of arch bridges, stability is one of the critical aspects for the design of arch bridges. Using 3D finite element model in ABAQUS, this paper has studied the stability performance of an arch bridge with inclined arch ribs and hangers, and the analysis also took the effects of geometrical and material nonlinearity into account. The impact of local buckling and residual stress of steel plates on global stability and the applicability of fiber model in stability analysis for steel arch bridges were also investigated. The results demonstrate an excellent stability of the arch bridge because of the transverse constraint provided by transversely-inclined hangers. The distortion of cross section, local buckling and residual stress of ribs has an insignificant effect on the stability of the structure, and the accurate ultimate strength may be obtained from a fiber model analysis. This study also shows that the yielding of the arch ribs has a significant impact on the ultimate capacity of the structure, and the bearing capacity may also be approximately estimated by the initial yield strength of the arch rib.

• 한국강구조학회 논문집
• /
• 제18권1호
• /
• pp.59-69
• /
• 2006

본 연구에서는 보 플랜지 절취형 (Reduced Beam Section, RBS) 철골모멘트접합부의 실험결과를 기초로 패널존의 적정강도를 제시하고자 하였다. RBS 충분한 실험자료가 보고 되어 있음에도 불구하고, 패널존의 적정강도 범위가 아직 제시된 바가 없다. 본 연구 및 다른 연구자의 실험결과에 의할 때, 패널존은 보 플랜지 그루브 용접부에 유해한 영향을 미치지 않고 0.01 radian의 소성회전각을 무난하게 발휘할 수 있음이 확인되었다. 또한 이 정도 크기의 패널존 소성변형을 허용하면 강한 패널존 시험체에 비해 횡비틀림 좌굴의 진폭이 절반 정도로 감소하였다. 이러한 실험적 관측을 토대로 RBS접합부의 소성변형능력을 향상시킴과 동시에 보의 소성힌지에 발생하는 좌굴의 크기를 줄일 수 있는 균형 패널존에 대한 강도 기준을 제안하였다.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.952-958
• /
• 1988

본 연구에서는 폭방향 불균일 냉각에 따른 열응력이 판변형 및 잔류응력의 주 요원인이라는 고려하에 냉각중에 압연판의 온도분포 및 열응력을 예측할 수 있는 수치 해석 모델을 구성하였다. 온도와 응력 계산에 상변태 현상을 고려하였으며, 판변형 은 압축성분 열응력에 의한 좌굴현상으로 고려하여 해석하였다.

• Computers and Concrete
• /
• 제5권6호
• /
• pp.525-544
• /
• 2008

In this research, the self-centering effect in precast and prestressed reinforced concrete structures was investigated experimentally. The reinforced concrete beams and columns were precast and connected by post-tensioning tendons passing through the center of the beams as well as the panel zone of the connections. Three beam-to-interior-column connections were constructed to investigate parameters such as beam to column interfaces (steel on steel or plastic on plastic), energy dissipating devices (unbonded buckling restrained steel bars or steel angles) and the spacing of hoops in the panel zone. In addition to the self-centering effect, the shear strength in the panel zone of interior column connections was experimentally and theoretically evaluated, since the panel zone designed by current code provisions may not be conservative enough to resist the panel shear increased by the post-tensioning force.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.55-60
• /
• 1999

In thin plate welding, welding deformation is deformation is produced in special form like buckling distortion, which is different from one in thick plate welding, large quantitatively, and has complicated form. Therefore, a particular countermeasure to prevent the welding deformation in manufacturing process is requested. Otherwise it takes more time to straighten the welding deformation than to fabricated a steel structure newly and in case of failing to straighten the welding deformation in beginning of the flame straightening process, even if the flame straitening is completed, the appearances is not good and sometimes eve refabrication is needed. To minimize these problems. In this present paper, the effects of the condition of support pin on out-of plane deformation produced by thin plate Butt welding in investigated through experiment and the countermeasure to prevent the welding deformation in suggested.

• 대한조선학회논문집
• /
• 제44권5호
• /
• pp.504-508
• /
• 2007

In the case of thin plate blocks, buckling deformation due to longitudinal shrinkage is the most important weld-induced deformation. This paper is concerned with developing the formula to predict the longitudinal shrinkage due to welding, in which mechanical tension effect in welding direction is accounted for. For this purpose, bead on plate welding test has been carried out for the 27 thin plate specimens with varying welding conditions and magnitude of tensile load. Empirical formula of predicting the longitudinal shrinkage has been derived based on the results of welding test, in which effect of mechanical tension is included. The derived formula can be usefully used in predicting the level of tensile load to reduce the longitudinal shrinkage.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.43-50
• /
• 2002

Main goal of this study is to develop MATLAB programming for exact analysis of distortional deformation of the straight box girder. For this purpose, a theory for distortional deformation theory is firstly summarized and then a BEF (Beam on Elastic Foundation) theory is presented using analogy of the corresponding variables. Finally, the governing equation of the beam-column element on elastic foundation is derived. An element stiffness matrix of the beam element is established via a generalized linear eigenvalue problem. In order to verify the efficiency and accuracy of the element using exact dynamic stiffness matrix, buckling loads for the continuous beam structures with elastic foundation and distortional deformations of box girders are calculated.

• 한국표면공학회지
• /
• 제38권1호
• /
• pp.14-20
• /
• 2005

The control of internal stress is extremely important in electroforming because of the deliberately low adhesion between the electro form and the mandrel. Excessive tensile or compressive stress can cause distortion, separation problem, curling, peeling or separation of electroform prematurely from the mandrel, buckling and blistering. Nickel sulfamate bath has been widely used in electroforming because of its low internal stress and moderate hardness. In this study, real-time stress sensor has been used for stress control in chloride-free nickel sulfamate bath for 400 mm x 300 mm x 500 ㎛ nickel electroform. It was found that compressive stress found at low current density indicated the contamination of electrolyte, which is very useful in procuring buckling and peeling of electroform. No compressive stress is allowed for plate electroform. The real-time stress can also be used for accurate stress control of nickel electroform. The tensile stress was found to be increased slightly with increase in nickel electroform thickness, i.e., from initial 1.47 ksi to 2.02 ksi at 320 ㎛.

• 한국터널지하공간학회 논문집
• /
• 제9권4호
• /
• pp.351-359
• /
• 2007

지반재료중의 하나인 암반의 물성평가 및 원지반상에서의 역학적 암반거동 평가를 위하여 다축(이축 혹은 진삼축) 압축실험이 수행되고 있다. 이러한 다축압축 실험의 경우에는 적용되는 경계조건에 따라 실험체내의 내부 응력이 예상과 다르게 작용하게 되며 결국 실험결과의 왜곡을 발생시킬 수 있으므로 적절한 경계조건의 설정은 필수적이다. 본 연구에서는 기존에 하중재하판과 실험체의 경계면상에서 발생할 수 있는 마찰저항을 감소시키기 위하여 사용된 철제 빗살구조의 재하판에 대한 구조 설계 방법을 제안하고자 한다. 각 빗살의 길이 및 단면의 계산을 위하여 각 빗살은 고정단에 지지된 단순보와 고정단에 지지된 기둥의 형태로 가정되었으며 좌굴과 실험체의 변형에 따른 빗살의 처짐을 고려하는 방법이 적용되었다.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.66-71
• /
• 2011

Recently, the production of shipbuilding and offshore plant industries, with a trend toward large structures, has led to an increased use of high strength ultra-thick plates. The use of ultra-thick plates increases the welding tasks, and the welding process generates distortion and residual stress in the weldment because of the rapid heating and cooling. Welding distortion and residual stress in the welded structure resulte in many troubles such as deformation and life deterioration. In particular, the welding residual stress has an important effect on welding deformation, fatigue, buckling strength, brittleness, etc. The purpose of this study was to evaluate the residual stress at a multi-pass weldment using an experimental method for EH36 high-tension steel. In this experimental method, AIS3000 was used to measure the residual stress of a welded part, HAZ, and base metal; EPMA and XRD were used to study the material properties.