• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1634-1640
• /
• 2012

This paper develops the high-efficiency drive system of the small-size electric vehicles (EVs) driven by the brushed dc motors. A power circuit for driving the dc motor is designed with the H-bridge circuit and buck converter by considering both the efficiency and cost. In order to change smoothly the rotating direction of dc motor driven by the proposed power circuit, an operating sequence for both the field current and the armature voltage according to an accelerator pedal angle is suggested. Through the simulation studies and experimental results with the low-cost 8-bit AVR, the performances of the proposed methods are verified.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.162-170
• /
• 2005

In KSLV-I, actuation system for thrust vector control of kick motor was configured as electro-hydraulic servo actuation system and consisted of actuators, hydraulic power supply system, hydraulic power distribution system and control system. In case of hydraulic power supply system, we use EMDP(Electric Motor Driven Pump) to supply hydraulic power. Generally, we use brushed DC motor for EMDP but it is not easy to operate EMDP using brushed DC motor at a high altitude. Hence, we are developing EMDP using brushless DC motor to use at a high altitude. In this study, we will explain control system for BLDC motor to drive hydraulic pump.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.6
• /
• pp.718-724
• /
• 2007

We extend the application of an adaptive controller previously introduced in the literature under the assumption that no actuator dynamics exists to the case when the dynamics of the brushed DC-motors used as actuators is not neglected. Convergence to the desired positions is ensured without requiring any feedback to cope with the additional electric dynamics. The proposed control scheme does not require the exact knowledge of neither robot nor actuator parameters to select controller gains.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.6-8
• /
• 2004

Recently, it is increasing to use more Brushless DC Motor with high energy density permanent magnet and semiconductor control unit for complementing the mechanical defect of Brushed DC Motors. For designing of BLDC Motors are required complex parameters like as rated characteristic, Geometries, B-H curve of magnet and steel materials, winding factor, etc. Moreover, design and manufacturing are difficult because of additional control circuits. Generally, Design parameters are gotten by analysis of Motor which is used. And the design parameters are used to design a new motor. But getting the design parameters through the eyes and experience is limited and it takes a long time. In this paper a method is proposed to efficiently analyze motor design parameters through the No load and Load Test, Back EMF Test, Simulation Analysis and Patent Analysis Method for existing BLDC Motor for a cooling Fan in Vehicle.

• Journal of Korean Society for Quality Management
• /
• v.47 no.3
• /
• pp.453-465
• /
• 2019

Purpose: A main purpose is to increase the operational rate and reduce operating maintenance costs by Improving the durability of Blower of Military Armored Vehicle and Self-propelled Artillery. As a result, it is expected to improve the service quality of customers. Methods: After analyzing the cause of the stop of the blower, the improvement plans were established and the effectiveness of each improvement plans were verified by testing. Results: Mechanical, electrical and environmental factors affecting brush wear were reviewed, but it was difficult to specify the cause, which necessitated a review of the application of the BLDC motor. Conclusion: After applying the BLDC motor to the blower, tests proved that the existing blower can be replaced. It is expected that this study will help improve the durability life of similar equipment that is applied with Brushed DC motors as well as blowers.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.104-106
• /
• 2003

In recent years for propulsion of cooling fan in cars are more used electrical motors than the engine direct coupled type. But the electrical motor which is now used has the brush and the commutator. Because of the brush and the commutator the electrical motor has short life time, low efficiency and mechanical- electrical noise. Therefore it is tried to develope brushless dc motor. The motor is located in the hot air from the radiator. The motor temperature increases high and the increasing of the motor temperature rolls big in its character. The cooling fan motor has relative small in size and input voltage is low. For 300 w output power must be the current of the motor high which causes high copper loss. In this paper will be tested and analysed characteristics of a dc motor which is now used for cooling fan and a BLDC motor will be designed with same character of the brushed motor and with considering of improvement of the efficiency. After design the motor should be analysed and tested.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.114-121
• /
• 2013

High efficiency operation is required for motors of vehicle to increase fuel efficiency due to the regulation of exhaust gas. This paper presents a control method of fuel pressure to increase fuel efficiency and a sensorless control method of BLDC motor to get higher efficiency than conventional brushed DC motor. Initial rotor position of BLDC motor is detected from current value that is occurred by test voltage pulse and rotor is accelerated by defined sequence to enter sensorless operation mode. The algorithm to control flow rate of fuel pump uses PI controller that is control motor speed to maintain the target fuel pressure commanded by ECU.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.1
• /
• pp.59-63
• /
• 2011

In small-power applications, variable-speed motors having high efficiency and controllability become more dominant than brushed DC motors. BLDC motors with permanent magnets in the rotor and SRMs directed by reluctance torque due to no permanent magnets have been strongly studied as a candidate. Compared to the BLDC motors, SRMs are more suitable for low-cost applications since the magnetic structure is simple, mechanically robust, and cheap due to no additional excitation in the rotor such as copper wire, aluminum, and permanent magnets. In addition, relatively small number of phases in single and two-phase SRMs allows more cost savings with regards to material in the motor and switching devices in the converter. In this paper, several 2 phase SRMs are compared to a 3 phase 6/4 SRM in terms of flux distribution in key parts of the motors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4083-4094
• /
• 2011

The Electric Power Steering (EPS) has been applied to the vehicles due to its better fuel efficiency, better steering feel, and the compact volume compared to the hydraulic power steering. The brushed PM (Permanent Magnet) DC motors had been adopted in most of the EPS systems until several years ago due to its easy control and a simple hardware configuration of the power converter, but nowadays the BLAC (Brushless AC) motor is becoming more popular for the EPS system because of its high efficiency and long lifetime. This paper reviews the configuration of the EPS system and the BLAC motor and drive technologies based on the papers published recently. The torque ripple reduction for steering feel and the fault detection algorithms for safety are also reviewed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.21-30
• /
• 2022

This paper describes the design, manufacture, and testing of servos applicable to small tracking radars. First, Chapter 1 describes the necessity of this study. Chapter 2 describes the development of servos applicable to future tracking radars in small missile systems. Chapter 3 describes the design and test results for current control of brushed DC motors, brushless DC motors, and permanent magnet synchronous motors. And Chapter 4 describes the design and test results for speed control of the test wheel. And in Chapter 5, the results of the previous tests are summarized. In this paper, some pictures were intentionally blurred for security reasons, and the control result of test wheel was described, not the test with the developed gimbals.