• Journal of Advanced Marine Engineering and Technology
• /
• 제25권2호
• /
• pp.344-350
• /
• 2001

This paper was studied on the characteristics of galvanic corrosion and its protection on heat exchanger tube plate in the sea water. In this paper, behavior of pitting corrosion of Ni-al bronze connected with Ti tube was measured af flow velocity of 0 m/s and 2.4 m/s. To protect galvanic corrosion, the protection characteristics of Ni-Al bronze connected with Ti tube by Zn-base alloys galvanic anode and hexagonal nylon insert was investigated. Main results obtained asre al follows: 1) The galvanic corrosion of Ni-Al bronze connected with Ti-tube is more active than single Ni-al bronze. 2) As the circuit resistance increase under the cathodic protection employing Zn-base alloys galvanic anode, Ni-al bronze connected with Ti tube is cathodically unpolarized. 3) The corrosion of Ni-Al bronze connected with Ti tube by nylon insert controls approximately 73% than not nylon insert.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권2호
• /
• pp.345-345
• /
• 2001

This paper was studied on the characteristics of galvanic corrosion and its protection on heat exchanger tube plate in the sea water. In this paper, behavior of pitting corrosion of Ni-al bronze connected with Ti tube was measured af flow velocity of 0 m/s and 2.4 m/s. To protect galvanic corrosion, the protection characteristics of Ni-Al bronze connected with Ti tube by Zn-base alloys galvanic anode and hexagonal nylon insert was investigated. Main results obtained asre al follows: 1) The galvanic corrosion of Ni-Al bronze connected with Ti-tube is more active than single Ni-al bronze. 2) As the circuit resistance increase under the cathodic protection employing Zn-base alloys galvanic anode, Ni-al bronze connected with Ti tube is cathodically unpolarized. 3) The corrosion of Ni-Al bronze connected with Ti tube by nylon insert controls approximately 73% than not nylon insert.

• 보존과학연구
• /
• 통권31호
• /
• pp.141-154
• /
• 2010

Many bronze artifacts have been excavated and preserved through conservation treatments in Korea but the analysis on artifacts was regarded as destruction of artifacts from the academic world of archaeology, Therefore, it is not so available to perform research on production techniques and provenances by with qualified analysis. Accordingly, there were only a few study cases about quality properties and production techniques But recently gradual change started to appear from the awareness of the need for the scientific approach to excavated artifacts. While Korean ancestors already had applied the different alloying ratios according to the use and shape of bronze artifacts, the analysis and study have been restrictedly performed. As a result, there was only a few analysis cases on a small minority of artifacts because they are the ancient relics, which made it hard to understand the bronze artifacts more deeply. This study researched into components rate, production techniques and hardness of bronze weapons such as a bronze sword and compared their alloying ratios with those of Chinese old records (周禮考工記, 金之六齊).

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2001년도 춘계학술발표대회 논문개요집
• /
• pp.31-34
• /
• 2001

Laser cladding Processing allows rapid transfer of heat to the material being minimum conduction into base metal. The effects of CO$_2$ laser cladding with high powder were investigated. High viscosity bronze powder consists of bronze powder used at a high temperature. The material has a high viscosity So that it can be substrate. Therefore. Laser cladding can be processed on a curved or slope surface. CO$_2$ laser cladding was designed It consists of the high viscosity bronze powder the shielding gas system and the preheating system The high viscosity powder properly at 0.3g/s and 0.50g/s. Because of the metallic bond between bronze per the hardness of dilution layer was suddenly increased. Experimental as results viscosity mixed powder can be a useful cladding material.

• 한국주조공학회지
• /
• 제19권6호
• /
• pp.484-492
• /
• 1999

The microstructures and mechanical properties of high strength yellow brass, Al bronze and Sn bronze alloys fabricated by gravity die casting and squeeze casting were investigated. A rapid cooling of casting was enhanced by pressure applied during solidification of Cu alloys, the cooling rate of casting was more great for high strength yellow brass alloy than other Cu alloys. Grain size and phases of the squeeze cast products become refined to 1/2 level compared to gravity die castings. Squeeze cast Al bronze and high strength yellow brass has about 10-20% higher yield and tensile strength and slighter decreased or nearly same elongation, compared to gravity die cast ones. Sn bronze has nearly same strength and hardness, but shows increased in elongation, compared to gravity die cast ones.

• 헤리티지:역사와 과학
• /
• 제52권2호
• /
• pp.142-171
• /
• 2019

용(龍)은 동서양 전설 신화에 등장하는 상상 속 동물이다. 서양의 용은 대부분 공격적이고 부정적 의미로 표현되지만, 동양에서는 황제를 상징하거나 상서로운 의미를 갖고 있어 긍정적 의미를 내포한다. 또한 용은 물을 다스리는 신물(神物)로 여겨져 그 종류가 다양해지고 이를 형상으로 표현하고자 했다. 고려시대 용과 관련된 기록은 "고려사"에서 다양한 주제로 등장하며, 크게 건국설화 기우제 신이(神異) 등과 관련되어 있다. 건국설화는 용을 통해 고려 왕권의 당위성을 강조하기 위한 것으로 '왕(王)=용손(龍孫)'이라는 '용손의식(龍孫意識)' 형성에 영향을 끼친다. 또한 용의 특징인 물을 다스리는 능력은 가뭄에 비를 바라는 기우제와 관련한 토용(土龍)으로 상징화된다. 이와 같은 용의 다양한 성격 중 용이 왕실의 상징이기에 용문(龍紋)의 사용은 민간에서 엄격히 제한되었으며, 용을 소재로 한 용문경(龍紋鏡) 역시 그 제작 사용에 있어 왕실과의 연관성을 배제하기 어렵다. 고려시대 쌍룡문경(雙龍紋鏡)은 종류 수량이 많은 편으로 중국에서 유입된 동경(銅鏡)과 함께 국내에서 제작한 쌍룡문경이 혼재하면서 고려시대 쌍룡문경의 제작과 유통은 다른 동경에 비해 활발했던 것으로 보인다. 이에 대해 본고에서는 10~14세기 중국에 존재한 다양한 쌍룡문경의 특징을 정리했다. 고려의 장인들은 쌍룡문경을 제작할 때 중국 쌍룡문경의 문양 구성에서 큰 영향을 받은 것으로 보인다. 이는 중국 쌍룡문경과 국적을 판별하기 어려운 예가 많으며, 그 차이 또한 면밀한 분석을 요하기 때문이다. 하지만 고려는 유입된 쌍룡문경을 그대로 답습했던 것은 아니며, 자체적으로 제작하고자 했음을 국내 현존하는 쌍룡문경의 유형 분류를 통해 살펴보았다. 세 가지 유형으로 나뉘는 쌍룡문경은 요대(遼代) 동경 계열인 I 유형이 가장 큰 비중을 차지하며, 그 외 II III 유형에서는 수량은 적으나 문양 구성이 독특한 쌍룡문경이 있어 고려에서 제작한 쌍룡문경으로 분석했다. 고려시대 쌍룡문경은 중국의 영향 하에서 제작된 만큼 고려에서 제작한 동경과의 구분이 어렵다는 점을 앞서 언급했다. 이중 평창 월정사 구층석탑에서 발견된 쌍룡문경은 그 제작지에 대한 의문점이 있으며, 동경의 문양 구성도 중국 쌍룡문경에서 찾아볼 수 없는 예이기에 이 동경에 대한 제작지를 검토했다. 이 쌍룡문경은 I 유형에 속하는 동경의 문양 구성을 갖추고 있으면서도 세부 문양의 조합이 중국에서 찾기 힘든 예라는 점에서 요대 동경의 문양 구성을 차용하여 고려에서 제작된 것임을 알 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.67-76
• /
• 1998

Friction materials for brake linings and clutches have severe performance requirements. The principal function of such frictional elements is to convert kinetic energy to heat, and then either to absorb or to dissipate heat. In order to achieve these objectives, the coefficient of friction must be as high as possible, independent of variations in operating conditions, and the necessary energy conversion must be accomplished with a minimum of wear on the contacting parts. In this study, Al powder, Al bronze powder and Mo powder used in general for automobile brake was sprayed on automobile brake disc to restrain rust and to maintain friction performance. Dynamo and corrosion tests have been carried out. It is concluded that the sprayed disc with Al bronze powder has the most improved frictional performance and anti-corrosive characteristics. The main results obtained can be summarized as follows; 1. From the corrosion current density test for gray cast iron and sprayed disc with powders of Al, Al bronze and Mo, it was cleared that the spray treatment with Al bronze powder showed the most superior anti-corrosive characteristics than other powders. 2. By anode polarization toward the noble direction from corrosion potential, corrosion current density with sprayed brake disc by Al-bronze powder was the lowest. 3. Mean frictional coefficients obtained from dynamo test are as follows : the sprayed disc with Al(99.99%) powder was 0.190 ; the sprayed disc with Al-bronze powder was 0.312 ; the sprayed disc with Mo powder was 0.257 ; the non-sprayed disc of gray cast iron was 0.331. In the case of the sprayed disc Al-bronze powder showed the most excellent frictional characteristics . 4. Amount of burnish quantity obtained from burnish test by dynamometer is as follows : the sprayed disc with Al-powder was 1.079 mm : the sprayed disc with Al-bronze powder was 0.155 mm : the sprayed disc with Mo powder was 0.253 mm : the non-sprayed disc of gray cast iron was 0.241 mm. Al-bronze powder also showed the most excellent burnish characteristics.

• 보존과학연구
• /
• 통권31호
• /
• pp.17-30
• /
• 2010

There were excavated many relics about 200 pieces including gilt-bronze cap, gilt-bronze shoes, bronze mirror and armor, etc. in Ahndong tumulus, Gildu-ri, Goheung. The National Research Institute of Cultural Heritage was undertaking excavation of major damaged relics that were corroded by several environment and were destroyed by a lump of earth. Shoes are consolidated with soils in order to stop destroy during excavation. And these are relocated in order to treat for conservation. Before treatment, X-ray radiography and CT(Computed Tomography) are used in order to examine the original surface and the shape of shoes. As a result, we confirm the condition of shoes. If soils are removed, gilt-bronze shoes are crumbling into little pieces because gilt-bronze shoes are damaged by corrosion and deformation. So, shoes are consolidating with inner soils and are removing outer soils. Throughout conservation treatment, shoes recovered original form and inner soils are consolidated in order to keep the shape of shoes.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.276-277
• /
• 2006

In order to accelerate the sintering of Al-Bronze powder covered with passive oxide film, we focused on the way to add Al-Ca fluoride consisting of $AlF_3$ and $CaF_2$, examined the effect of the $CaF_2$ mixing rate in Al-Ca fluoride, the amount of the added Al-Ca fluoride and the sintering temperature on sintering properties of Al-Bronze powder and considered the mechanism of the sintering acceleration. Al-Bronze powder was sintered most effectively by adding Al-Ca fluoride with the $CaF_2$ mixing rate of 20mass%. If the amount of added fluoride was over 0.05mass% and the sintering temperature was over 1123K, the sintering acceleration of the Al-Bronze powder appears. Regarding the mechanism of the sintering acceleration, it was presumed that $Al_2O_3$ film on the surface of the Al-Bronze particles was removed in the process of the formation of gaseous AlOF by the reaction with $AlF_3$, and the reaction was accelerated further by the presence of the liquid phase which is formed in Al-Ca fluoride.

• 한국지형학회지
• /
• 제25권4호
• /
• pp.103-116
• /
• 2018

The purposes of this research are as follows: First, to reconstruct the optimal locational environment of the Bronze Age settlement in Cheonan Baekseok-dong (hereinafter referred to as the study settlement). Second, to identify the priority ranking of the topographical factors that influenced the Bronze Age people when selecting their the settlement location. For these reasons, the topographical factors of the 200 Bronze Age dwellings (hereinafter referred to as dwellings) confirmed in the survey area were analyzed through the ridge's environmental perspective. The results are asfollows: First, the optimal ridge environment of the Bronze Age settlement is largely a sub-ridge in N-S direction (for example, NNW-SSE, N-S, NNESSW), especially at the top (Crest slope, Crest flat) of the south-facing aspect of the ridge. Second, when the Bronze Age dwellers selected a residential location, they carefully considered topographical factors in the following order: (1) the slope direction of the ridge surface, (2) the micro-landform of the ridge, (3) the ridge scale, (4) the ridge direction, and (5) the surface relief. The results of this study could be used as basic data in related fields such as archaeology, quaternary research, and traditional architecture and so on.