• ETRI Journal
• /
• v.40 no.6
• /
• pp.794-801
• /
• 2018

This paper proposes a novel graphene-based optical microelectromechanical systems MEMS accelerometer that is dependent on the intensity modulation and optical properties of graphene. The designed sensing system includes a multilayer graphene finger, a laser diode (LD) light source, a photodiode, and integrated optical waveguides. The proposed accelerometer provides several advantages, such as negligible cross-axis sensitivity, appropriate linearity behavior in the operation range, a relatively broad measurement range, and a significantly wider bandwidth when compared with other important contributions in the literature. Furthermore, the functional characteristics of the proposed device are designed analytically, and are then confirmed using numerical methods. Based on the simulation results, the functional characteristics are as follows: a mechanical sensitivity of 1,019 nm/g, an optical sensitivity of 145.7 %/g, a resonance frequency of 15,553 Hz, a bandwidth of 7 kHz, and a measurement range of ${\pm}10g$. Owing to the obtained functional characteristics, the proposed device is suitable for several applications in which high sensitivity and wide bandwidth are required simultaneously.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.6022-6026
• /
• 2012

This article presents a band-stop filter (BSF) by using a periodic structure property of frequency selective surfaces (FSSs) embedded in a microstrip transmission line. The proposed BSF is designed with FSS unit cells modifying the cross-loop slots. The BSF is interpreted with an equivalent circuit model and a dispersion diagram. The center frequency (fo) of the BSF is 6.6GHz. Proposed filter increases the number of unit cell. As a result, 3dB bandwidth is wider and insertion loss is reduced. Also, Facbricated BSF exhibits uniplanar geometry, simple fabrication.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3074-3078
• /
• 2014

We implemented a dual-band slot-coupled patch (SCP) antenna for the external access point (AP) of the wireless local area network (WLAN) band. The antennas consist of two radiators on three layers. The first radiator is a slotted bow tie antenna operating at the 2.4-2.483 GHz band. The second radiator is a patch antenna with parasitic elements operating at 4.095-5.845 GHz. The high gain and broad bandwidth is important element of wireless access. To enhance the bandwidth, a coupled feeding was used in the first radiator and a parasitic patch was used in the second radiator. We used a parasitic patch and chock to improve the directivity and isolation in both radiators. The porposed antenna was designed by EM simulation tool and measured. The S11 of the antenna was less than -11dB (VSWR 1.8:1) at operating frequency. The peak gain was more than 6 dBi in the first antenna and more than 8 dBi in the second antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.8
• /
• pp.718-729
• /
• 2015

A S / X dual broad band patch antenna with shared aperture structure is fabricated. A $2{\times}2$ perforated patch is used for S-band operation and a $2{\times}2$ patch antenna array is integrated in the $2{\times}2$ perforation for X-band operation. The measurement results of a S / X dual broad band patch antenna with shared aperture structure show the broad band characteristics larger than 20 % in both bands.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.6
• /
• pp.317-326
• /
• 1985

A broad-band design method of a lumped-element 3dB quadrature hybrid without magnetic coupling is proposed and discussed, where techniques of cascading fundamental hybrids via second-order delay equalizers and adding matching sections are adopted. It is shown that the designed broad-band lumped-element 3dB quadrature hybrid can be easily constructed and its bandwidth reaches up to 54%. Furthermore, the esperiments have been carried out, the results of which agree with the theoretical ones, and hence, the validity of the broad-band design method proposed here was confirmed.

• Korean Journal of Optics and Photonics
• /
• v.21 no.5
• /
• pp.195-199
• /
• 2010

A broadband optical coupler with a broad bandwidth of 1000 nm based on a photonic crystal fiber (PCF) is investigated. The PCF has 6 layers of air hole structures and a diameter of $130{\mu}m$. The PCF-based coupler is fabricated by using a fused biconical tapering method based on heating and elongation processes. Changing temperature and an elongation length can control the bandwidth and the bandedge wavelength of the PCF-based broadband coupler. The diameter of the fused region in the PCF-based coupler was measured to be $23{\mu}m$. The fabricated PCF-based coupler has a nearly-flat coupling ration of 3-dB in a broad bandwidth of 1000 nm, which is wider than that of the previously reported PCF-based coupler and that of the single-modefiber-based coupler. Since the resolution of optical coherence tomography system is proportional to the bandwidths of both an optical light sources and an interferometer, the fabricated PCF-based broadband optical coupler has a great potential for realization of a broadband interferogram.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1649-1651
• /
• 2002

Ultra-wide bandwidth (UWB) detection method has been widely used as a front end detection scheme for the ultra-high frequency (UHF) partial discharge (PD) monitoring systems. A broad-band video detector module was developed and characterized for the UHF UWB PD detection systems. The useable bandwidth of the module is more than 2 GHz and it is optimized for 50-ohm systems. The detection sensitivity and dynamic range of the module were characterized by using a known ns-width RF pulses of GHz range. The dynamic range is more than 6-decades and the module can detect pulsed RF signals down to 1 nW. The detector module can eliminate expensive equipment such as high speed oscilloscopes and radio frequency (RF) spectrum analyzers. Therefore, it enables one to use slow speed data acquisition systems for the PD monitoring at the UHF range. The detector module was used to detect real PDs of about <3 pC. The module converts the UWB PD signals into a low-bandwidth video signal with a high signal-to-noise ratio.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.8-15
• /
• 1998

In this paper, to improve the bandwidth of microstrip antenna, we discussed parasitic patch structure coupled capacitively at radiating slot. To reduce the overal size of antenna,$\lambda$/4 short structure is accepted instead of $\lambda$/2 patch. Since ground plane is reduced, backward radiation is occurred. The characteristics of the designed antenna is evaluated, based on the transmission line model and the aperture analysis method. And by computer program the radiation pattern and return loss are evaluated. As simulation results, backward radiation is -15 dB. Bandwidth of constructed antenna is 167 MHz at the resonant frequency of 2.45 GHz, which is very broad, compared to conventional microstrip antennas. Therefore the proposed antenna will be suitable for very wide bandwidth communications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6A
• /
• pp.918-926
• /
• 2000

A huge storage and broad bandwidth are required to provide subscribers with VoD services. Hence, there is a huge amount of cost in establishing networks for VoD services. To determine how to reduce the cost, a number of studies involving such as distributed server systems, multicasting, program caching, stream sharing, are currently in progress. In this paper, a request criterion for multicast service and the ratio of required bandwidth for unicast to multicast are generated. The effect of multicast service on network bandwidth, server bandwidth, and buffer size was analyzed and validated through computer simulation. The results of this study could be applied to efficient designing networks for VoD services.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.3
• /
• pp.50-56
• /
• 2010

In this paper, compact broad-band antenna using circular spiral slot and CPW (coplanar waveguide) feed is proposed. The proposed antenna is designed on the same plane of the substrate by using CPW fed structure, archimediean spiral slot structure. So it was achieved both the size of compact antenna and the broad band. A archimediean spiral slot structure is introduced for resonance of medium band operation. The distances of a CPW feeder line and a ground plane are modified for impedance matching and lower/higher band operation. The proposed antenna has a compact size ($8mm\;{\times}\;13mm$) and it is etched on the FR-4 (relative dielectric constant 4.4, thickness 0.8mm) dielectric substrate. The simulated impedance bandwidth (VSWR $\leq$ 2) and maximum gain of the proposed antenna are 5.98GHz (4.1GHz ~ 10.08GHz) and 3.97dBi, respectively. The measured impedance bandwidth (VSWR $\leq$ 2) and maximum gain of the proposed antenna are 6.02GHz (4.48GHz ~ 10.5GHz) and 2.68dBi, respectively. The simulation and measured result shows good impedance matching and radiation pattern over the interesting frequency bands. It can be applied to antenna of broad-band wireless communication system.