• Earthquakes and Structures
• /
• 제12권2호
• /
• pp.237-250
• /
• 2017

There has been increasing attention in many countries on seismic retrofit of old fashioned RC structures in recent years. In such buildings, the joints lack transverse reinforcement and suffer inadequate seismic dimensional requirements and the reinforcement is plain bar. The behavior of the joints is governed by sliding of steel bars and diagonal shear failure is less influential. Different methods to retrofit beam-column joints have been proposed in the literature such as wrapping the joint by FRP sheets, enlargement of the beam-column joint, and strengthening the joint by steel sheets. In this study, an enlargement technique that uses external prestressed cross ties with steel angles is examined. The technique has already been used for substructures reinforced by deformed bars and has advantages such as efficient enhancement of seismic capacity and lack of damage to the joint. Three reference specimens and two retrofitted units are tested under increasing lateral cyclic load in combination with two levels of axial load. The reference specimens showed relatively low shear strength of 0.150${\surd}$($f_c$) and 0.30${\surd}$($f_c$) for the exterior and interior joints, respectively. In addition, relatively brittle behavior was observed and large deformations extended into the panel zone of the joints. The retrofit method has increased ductility ratio of the interior beam-column joints by 63%, and energy dissipation capacity by 77%, relative to the control specimen; For external joints, these values were 11%, and 94%. The retrofit method has successfully relocated the plastic joints far from the column face. The retrofit method has improved shear strength of the joints by less than 10%.

• 콘크리트학회논문집
• /
• 제25권6호
• /
• pp.667-674
• /
• 2013

기존 강재 브레이싱 내진보강법은 정착부의 안정성 문제와 브레이싱의 국부좌굴이 발생할 문제가 있으며, 이를 방지하기 위한 추가보강으로 인해 불필요한 자중증가 등으로 경제적인 내진보강성능 확보에 어려움이 있다. 이 연구에서는 지진피해를 받은 건물에 지진피해로 인한 기존 기둥의 연성확보를 위해서 유리섬유시트(glass fiber sheet)로 래핑을 함과 동시에 기존 철골 X-브레이싱 내진보강법에 비교해서 경량의 고강도 재료로 보강 후 추가적인 중량증가가 거의 없으며, 브레이싱 압축 좌굴거동에 자유로운 탄소섬유 앵커 X-브레이싱공법(carbon fiber X-brace)을 조합한 경제적이며 효과적인 새로운 내진보강법(GFS-CFXB)을 제안하였다. 이 연구에서 제안한 GFS-CFXB공법의 유용성을 검증할 목적으로 지진피해를 받은 골조를 대상으로 반복가력에 의한 구조실험을 실시하여 내진성능 및 내진보강 효과를 검증하였다.

• Composites Research
• /
• 제16권6호
• /
• pp.48-55
• /
• 2003

본 연구는 알루미늄 합금(AC8A)과 금속복합재료 (A1/A12O3) 및 혼합금속 복합재료(A1/A12O3/A12O3p)의 피로시험 결과 비교와, 일정진폭 피로 하중으로부터 예측한 수명과 실험으로부터 얻은 피로 수명의 비교하는 것이고, 음향방출(Acoustic Emission, AE) 방법을 이용하여 피로 시험 시 균열 발생의 측정 및 예측을 하고자 하였다. 노치재의 실험결과에 따르면, 세라믹 보강재의 첨가로 인해 기지재 보다 연성이 저하된 하이브리드 금속 복합재료와 단일 금속 복합재료의 피로 수명은 두 가지 하중 조건에서 모두 기지재 보다 더욱 짧은 수명을 나타내었다. 또한 누적피로수명평가 방법을 통해 예측된 피로수명은 랜덤하중 하에서 실험을 통해 얻어진 피로 수명과 거의 일치하였다.

• 한국전산구조공학회논문집
• /
• 제18권3호
• /
• pp.303-309
• /
• 2005

본 연구에서는 국내 원전에서 기기 정착을 위하여 가장 널리 적용되는 직매형 앵커기초를 대상으로 앵커기초의 인장 설계기준에 대한 적정성을 검토하기 위하여 수치해석이 수행되었다. 본 연구에서 수치해석모형에 적용된 파괴기준으로서 콘크리트와 같은 유사 취성재료에는 Microplane모형이, 앵커볼트와 같은 연성재료에는 탄성-완전 소성모형이 적용되었다. 그리고, 균열 발생현상을 모사하기 위하여 분산균열모형을 채택하였다. 개발된 수치해석모형은 다양한 경우의 실증시험결과를 근거로 신뢰성이 검증되었으며, 검증된 수치해석모형과 앵커볼트의 유효매입깊이를 변수로 한 다양한 경우에 대한 수치해석을 통하여 직매형 앵커기초의 인장설계기준으로서 적용이 가능한 ACI 349 Code와 CEB-FIP Code가 평가되었고, 그 보수성이 확인되었다.

• Structural Engineering and Mechanics
• /
• 제6권2호
• /
• pp.125-141
• /
• 1998

Recent test results of steel moment connections repaired with a haunch on the bottom side of the beam have been shown to be a very promising solution to enhancing the seismic performance of steel moment-resisting frames. Yet, little is known about the effects of using such a repair scheme on the global seismic response of structures. When haunches are incorporated in a steel moment frame, the response prediction is complicated by the presence of "dual" panel zones. To investigate the effects of a repair on seismic performance, a case study was conducted for a 13-story steel frame damaged during the 1994 Northridge earthquake. It was assumed that only those locations with reported damage would be repaired with haunches. A new analytical modeling technique for the dual panel zone developed by the author was incorporated in the analysis. Modeling the dual panel zone was among the most significant consideration in the analyses. Both the inelastic static and dynamic analyses did not indicate detrimental side effects resulting from the repair. As a result of the increased strength in dual panel zones, yielding in these locations were eliminated and larger plastic rotation demand occurred in the beams next to the shallow end of the haunches. Nevertheless, the beam plastic rotation demand produced by the Sylmar record of 1994 Northridge earthquake was still limited to 0.017 radians. The repair resulted in a minor increase in earthquake energy input. In the original structure, the panel zones should dissipate about 80% (for the Oxnard record) and 70% (for the Sylmar record) of the absorbed energy, assuming no brittle failure of moment connections. After repair, the energy dissipated in the panel zones and beams were about equal.

• Steel and Composite Structures
• /
• 제27권6호
• /
• pp.727-745
• /
• 2018

The design criteria and the corresponding performance levels characterize the response of extended stiffened end-plate beam-to-column joints. In order to guarantee a ductile behavior, hierarchy criteria should be adopted to enforce the plastic deformations in the ductile components of the joint. However, the effectiveness of thesecriteria can be impaired if the actual resistance of the end-plate material largely differs from the design value due to the potential activation of brittle failure modes of the bolt rows (e.g., occurrence of failure mode 3 in the place of mode 1 per bolt row). Also the number and the position of bolt rows directly affect the joint response. The presence of a bolt row in the center of the connection does not improve the strength of the joint under both gravity, wind and seismic loading, but it can modify the damage pattern of ductile connections, reducing the gap opening between the end-plate and the column face. On the other hand, the presence of a central bolt row can influence the capacity of the joint to resist the catenary actions developing under a column loss scenario, thus improving the joint robustness. Aiming at investigating the influence of these features on both the cyclic behavior and the response under column loss, a wide range of finite element analyses (FEAs) were performed and the main results are described and discussed in this paper.

• 한국전산구조공학회논문집
• /
• 제22권6호
• /
• pp.527-532
• /
• 2009

고속충돌 파괴현상에 대한 병렬계산기법을 다루었다. 특히 세라믹 재료는 다른 연성 금속 재료와 달리 강성이 크고 가볍기 때문에 충돌 방호 구조물로 활용이 되고 있다. 재료의 고속 관통 문제의 경우 매우 짧은 시간에 대변형이 일어나며, 세라믹 재료의 깨지는 특성 때문에 실험적으로 이를 분석하기 매우 어렵다. 본 연구에서는 세라믹 파괴현상을 수치적으로 모사하기 위해 절점분리기법을(node separation scheme) 적용하였다. 절점분리기법의 제약으로는 재료의 파괴가 발생함에 따라 새로운 절점이 생기게 되고, 이로 인해 지속적으로 계산 시간이 늘어난다는 사실이다. 해석 시간을 단축하기 위해 MPI(Message Passing Interface)를 이용한 병렬화를 수행하였다. 고속충돌 문제의 특이사항으로 시간에 따라 각각의 프로세서에 할당된 영역의 계산량이 비균일 해지며, 이로 인한 병렬 성능의 저하가 발생한다. 본 연구에서는 이를 방지하기 위해 동적영역할당기법을 적용하였다. 고속충돌 문제 해석을 통하여 적용된 기법의 정확성 및 병렬 성능에 대해 기술하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권5호
• /
• pp.136-145
• /
• 2013

최근 발생한 대규모 지진으로 구조물의 내진보강에 대한 사회적 관심도가 높아지고 있다. 특히 내진 설계가 반영되지 않은 기둥은 취성적인 파괴로 구조물 전체붕괴를 유발하기 때문에 내진보강이 적용 되어야한다. 과거에는 단면증설법, 강판보강법등이 주로 적용되었고 최근에는 복합재료의 장점을 이용한 섬유보강법이 선호되고 있다. 그러나 이러한 보강법들은 구조물의 물리적 손상을 유발하며, 작업공간과 시간소비가 크다는 단점이 있다. 본 연구에서는 기존 보강법의 단점을 보강하여 복합재료 (Fiber reinforced polymer)와 Aluminum 체결부 이용한 FRP 내진보강재를 개발하였다. 비선형 유한요소 해석프로그램을 통해 개발된 FRP 내진보강재의 최적 보강량을 결정하였다.

• Advances in concrete construction
• /
• 제11권4호
• /
• pp.335-345
• /
• 2021

It is known from the literature that there are relatively few studies on the engineering properties of ultra-high performance concrete (UHPC) in early age. In fact, in order to ensure the safety of UHPC during construction and sufficient durability and long-term performance, it is necessary to explore the early behavior of UHPC. The test parameters (test control factors) investigated included the percentage of cement replaced by silica fume (SF), the percentage of cement replaced by ultra-fine silica powder (SFP), the amount of steel fiber (volume percent), and the amount of polypropylene fiber (volume percentage). The engineering properties of UHPC in the fresh mixing stage and at the age of 7 days were investigated. These properties include freshly mixed properties (slump, slump flow, and unit weight) and hardened mechanical properties (compressive strength, elastic modulus, flexural strength, and splitting tensile strength). Moreover, the effects of the experimental factors on the performance of the tested UHPC were evaluated by range analysis and variance analysis. The experiment results showed that the compressive strength of the C8 mix at the age of 7 days was highest of 111.5 MPa, and the compressive strength of the C1 mix at the age of 28 days was the highest of 128.1 MPa. In addition, the 28-day compressive strength in each experimental group increased by 13%-34% compared to the 7-day compressive strength. In terms of hardened mechanical properties, the performance of each experimental group was superior to that of the control group (without fiber and without additional binder materials), with considerable improvement, and the experimental group did not produce explosive or brittle damage after the test. Further, the flexural test process found that all test specimens exhibited deflection-hardening behavior, resulting in continued to increase carrying capacity after the first crack.

• Earthquakes and Structures
• /
• 제21권6호
• /
• pp.613-625
• /
• 2021

Non-seismically designed eccentric reinforced concrete beam-column joints were extensively used in existing reinforced concrete frame buildings, which were found to be vulnerable to seismic action in many incidences. To provide a fundamental understanding of the seismic performance and failure mechanism of the joints, three 2/3-scale exterior beam-column joints with non-seismically designed details were cast and tested under reversed cyclic loads simulating earthquake excitation. In this investigation, particular emphasis was given on the effects of the eccentricity between the centerlines of the beam and the column. It is shown that the eccentricity had significant effects on the damage characteristics, shear strength, and displacement ductility of the specimens. In addition, shear deformation and the strain of joint hoops were found to concentrate on the eccentric face of the joint. The results demonstrated that the specimen with an eccentricity of 1/4 column width failed in a brittle manner with premature joint shear failure, while the other specimens with less or no eccentricity failed in a ductile manner with joint shear failure after beam flexural yielding. Test results are compared with those predicted by three seismic design codes and two non-seismic design codes. In general, the codes do not accurately predict the shear strength of the eccentric joints with non-seismic details.