• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.532-535
• /
• 2003

In this paper, we made study for plastic chip antenna, the plastic is Formax with the circle of PVC and its electric characteristics are dielectric constant 1.9, surface current $10{\Omega}$. The proposed antenna same as the conventional antenna are usually constructed with ceramic chip, which are not fragile in nature and don't tend to break easily. Therefore the proposed antenna with its advantage are attractive for application in mobile antenna. We study the dual-band plastic chip antenna resonated at 800Mhz and 1800Mhz. From this study results, we feel confident of application for mobile phone antenna.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.655-656
• /
• 2015

In this paper, diagnosis for 85 high voltage induction motors which have operated for more than 20 years in 18 wide area water supply offices were applied and the results of diagnosis were analysed. Furthermore, main factors that would be affecting rotor defects were selected and correlations between dependent variables which was magnitude for sideband frequency on current during operation and independent variables such as starting characteristic, operating time, number of operation, load factor, maker, rotation speed, capacity were analysed. It was clear that factors including starting characteristic, number of operation, maker, rotation speed caused break by correlation analysis. From this, regression equation was deduced through regression analysis. Based on suggested regression equation, it is applied usefully that we can estimate the condition of rotor without onsite diagnosis and plan the schedule of diagnosis.

• Journal of the Korean Society of Safety
• /
• v.15 no.4
• /
• pp.88-94
• /
• 2000

The adsorption characteristics of Tharonil on granular activated carbon were experimentally investigated in an adsorber and in a packed column. It was estabilished that the adsorption equilibrium of Tharonil on granular activated carbon was more successfully fitted by Freundlich isotherm equation than Langmuir isotherm equation in the concentration range from 1 to 1000 mg/1. Intraparticle diffusivities (pore and surface diffusivity) of Tharonil were estimated by the concentration-time curve and adsorption isotherm. The estimated values of pore diffusivity and surface diffusivity are $6.70{\times}10^{-6}$ and $2.0{\times}10^{-9}cm^2/s$, respectively. From comparison of intraparticle diffusivities, it was found that surface diffusion was the limiting step for adsorption rate. The break time and breakthrough curve predicted by constant pattern-linear driving force model were shown to agree with the experimental results.

• Journal of the Korean Society of Safety
• /
• v.32 no.2
• /
• pp.112-116
• /
• 2017

Present study investigated the influence of time step size, turbulent eddy viscosity, and the number of layer on rapid and unsteady propagation of dam break flow. When the time step size had a value such that it resulted in Cr of 0.89, a significant numerical oscillation was observed in the vicinity of the wave front. Higher turbulent viscosity ensured smooth and mild slope of velocity and water stage compared with the flow behavior by no viscosity. The vertical velocity at the lower layer positioned near the bottom showed lower velocity compared with other layers.

• Journal of the Korean Statistical Society
• /
• v.28 no.2
• /
• pp.265-277
• /
• 1999

Classical and inverse estimation methods are two well known methods in statistical calibration problems. When there are outliers, both methods have large MSE's and could not estimate the input value correctly. We suggest median calibration estimation based on the LD-statistics. To investigate the robust performances, the influence function of the median calibration estimator is calculated and compared with other methods. When there are outliers in the response variables, the influence function is found to be bounded. In simulation studies, the MSE's for each calibration methods are compared. The estimated inputs as well as the performance of the influence functions are calculated.

• Tribology and Lubricants
• /
• v.8 no.2
• /
• pp.14-19
• /
• 1992

rate of growth of "protective" films of oxides and compounds derived from the lubricant. The protection afforded by the films is strongly dependent on lubricant and steel composition, initial composite surface roughness and the load/speed sequence or history in the early stages of sliding. The protective films, formed by chemical and mechanical action between lubricant and mating surfaces, delayed the surface roughening and offered higher load capacity. Given the great number of variables involved it is not possible to follow more than a few of the chemical changes on surfaces at the end of experiments. Ellipsometry was therefore used to monitor the formation and loss of dual protective films in real time, and also to find the effect of protective films on scuffing and break-in depending on lubricant conditions.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11b
• /
• pp.119-125
• /
• 2005

A method of predicting the tritium concentration in the air leaving an atmospheric detritiation dryer was modeled for designing a fixed bed dryer and preparing an advanced dryer control. In order to quantify the bed utilization and the dynamic capacity against an inlet humidity and a flow rate, a series of quantitative tests based on the break-through behavior were carried out in an isothermal fixed bed of synthetic zeolites such type as molecular sieve 4A, 5A, 13X and mordenite. The amount of water vapor breaking during the adsorption was estimated to give a breakthrough capacity at the various inlet flow rates and humidity conditions. The molecular sieve 13X exhibited a better adsorption performance at a given bed height.

• Food Science and Biotechnology
• /
• v.18 no.5
• /
• pp.1155-1160
• /
• 2009

Poly(lactide) (PLA)-coated paperboards were prepared by solution coating and thermo-compression coating methods and their effect of coating on the packaging properties such as tensile, water resistance, water vapor barrier, and heat sealing properties was tested. Compared with uncoated control paperboard, tensile strength (TS) of PLA-coated paperboard increased profoundly (2.2-2.6 folds) with slight increase in elongation at break (E). Water absorptiveness (WA) of the paperboard decreased 74-170 folds and water vapor permeability (WVP) decreased 6.3-22.1 folds by coating with PLA, which indicates an increase in the hydrophobicity of the surface of paperboard. Compared with polyethylene (PE)-coated paperboard, both PLA-coated paperboard exhibited 2.3 time higher heat sealing strength. In addition, the PLA-coated paperboards showed equal or higher wet TS than PE-coated paperboard. All the test results showed that the paperboard coated by the thermo-compression coating method was similar to or better than those of coated by the solution coating method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.185-187
• /
• 2006

This study deals with characterization and the application of magnetoelasticity as a device which measures existing steel stress. Available method of measuring existing stress needs break the concrete and cut the steel bar. But Proposed method doesn't need to cut the steel bar. A successful application of magnetoelasticity depends on the linearity of the relationship between the elastic and magnetic response due to loading. To investigate the correlation between two, steel bars are loaded in tension under uniaxial loading while the magnetic reading is recorded. Results showed linearity or partial-linearity of the elastic behavior of steel bars in relation to magnetic change. In the paper, the various factors affecting the measurements are also discussed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.8
• /
• pp.396-402
• /
• 2006

Even the case DC circuit Breaker have good quality for interruption of high current like heavy load current, short-circuit current, the verification for small current breaking capability of circuit breaker should be performed. It comes from the reason DC small current breaking failure can be lead to break out second heavy fault condition and in the long run substation shutdown. In this paper, we can find the characteristics of DC small current and international test standard discription about small current breaking and one of the proper solution to get over it.