• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.4
• /
• pp.766-774
• /
• 2013

Biodegradable polybutylene succinate(PBS) is a kind of environmentally friendly plastics for fisheries, because it can mitigate the ghost fishing problem caused by gill-net and trap fisheries. To evaluate durability of PBS monofilament, each of different diameter 3 types of monofilaments were spun and exposed to 56 month outdoor and then their gravity, modification of surface, breaking strength, and elongation were analysed. The gravity of PBS monofilament was estimated to be approximately 1.24 when spinning ratio from 4.8 to 6.1. PBS monofilaments did not show any crack after 56 month exposed to outdoor and load-elastic elongation curve was showed sigmoid type. Decreasing ratio of elongation was appeared in the thinnest monofilament 0.2mm diameter and breaking strength was in the thickest monofilament 0.4mm diameter. Breaking strength and elongation at break were decreased rapidly after 48 month exposed to outdoor. Breaking strength reduced linearly after 48 month exposure, while no such linear relationship was found in the case of elongation at break. In results, it was investigated that the durability of PBS monofilament nets for gillnet and trap were 24, 50 month when keep to land, respectively.

• Nuclear Engineering and Technology
• /
• v.47 no.4
• /
• pp.434-442
• /
• 2015

The advanced passive pressurized water reactor (PWR) is being constructed in China and the passive residual heat removal (PRHR) system was designed to remove the decay heat. During accident scenarios with increase of heat removal from the primary coolant system, the actuation of the PRHR will enhance the cooldown of the primary coolant system. There is a risk of power excursion during the cooldown of the primary coolant system. Therefore, it is necessary to analyze the thermal hydraulic behavior of the reactor coolant system (RCS) at this condition. The advanced passive PWR model, including major components in the RCS, is built by SCDAP/RELAP5 code. The thermal hydraulic behavior of the core is studied for two typical accident sequences with PRHR actuation to investigate the core cooling capability with conservative assumptions, a main steam line break (MSLB) event and inadvertent opening of a steam generator (SG) safety valve event. The results show that the core is ultimately shut down by the boric acid solution delivered by Core Makeup Tank (CMT) injections. The effects of CMT boric acid concentration and the activation delay time on accident consequences are analyzed for MSLB, which shows that there is no consequential damage to the fuel or reactor coolant system in the selected conditions.

• Plant Biotechnology Reports
• /
• v.5 no.1
• /
• pp.35-43
• /
• 2011

This communication describes for the first time an efficient and reproducible protocol for large-scale multiplication of Bambusa nutans. Nodal segments collected from field-grown clumps and cultured on Murashige and Skoog (MS) medium supplemented with $4.4{\mu}M$ benzylaminopurine (BA) and $2.32{\mu}M$ kinetin (Kin) gelled with 0.2% gelrite yielded 80% aseptic cultures with 100% bud-break. The in vitro-formed shoots obtained after bud-break were successfully multiplied in MS liquid medium supplemented with $13.2{\mu}M$ BA, $2.32{\mu}M$ Kin, and $0.98{\mu}M$ indole-3-butyric acid (IBA). Sub-culturing of shoots every 3 weeks on fresh multiplication medium yielded a consistent proliferation rate of 3.5-fold. Shoot clusters containing three to five shoots were successfully rooted with 100% success on half-strength MS liquid medium supplemented with $9.8{\mu}M$ IBA, $2.85{\mu}M$ indole-3-acetic acid (IAA), $2.68{\mu}M$ naphthaleneacetic acid (NAA), and 3% sucrose. Plantlets grown in vitro were acclimatized and subsequently transferred to the field. Inter-simple sequence repeat analysis has confirmed the genetic uniformity of the tissue-cultured plants up to 27 passages.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.4 no.4
• /
• pp.27-43
• /
• 2009

Location decision problems of franchisees which determine revenues and costs in business are one of the most important issues in franchisor research. The major portion of franchisees are located in Kyunegi-do and 5 major cities in Korea. What's the reason behind this fact? The purpose of this research is to provide the rationale for location decisions of franchisor businesses. Based on the break-even analysis, we conclude that major decisive factors of location decisions are demand and costs of franchisor businesses. At the good location which can attract many customers, franchisor businesses can be much more competitive than independent stores. However, at the bad location, franchisor businesses can not be maintained because of high costs.

• The Journal of Asian Finance, Economics and Business
• /
• v.5 no.4
• /
• pp.21-34
• /
• 2018

The study tests the Fama and French three-factor model by using the newly created Islamic equity style indices. Based on a dataset from May 2006 to April 2011, the three-factor model is tested based on returns of Islamic unit trust funds using the Generalized Method of Moments (GMM) methodology. The sample period is also divided between periods before and after the Global Financial Crisis in August 2008 to test for robustness, and the Bai and Perron (2003) multiple structural break test was used to determine the structural break in the series. The analysis shows that the Fama and French model is valid for Islamic unit trust funds before and after the collapse of Lehman Brothers. The result further indicates the reversal of size effect. As for trading strategies, value funds outperform growth funds by annualized 3.13 percent for the full period. During pre-crisis period, value funds perform better than growth funds while in post-crisis, size factor yields better return than other strategies. As policy suggestion, fund managers need to be aware of the reversal of size effect, and they need to ensure a more transparent stock selection process so that investors can make an informed decision in their asset allocation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.106-112
• /
• 2008

Modern vehicles require a high degree of refinement, including good drive ability to meet customer demands. Vehicle drive ability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. This paper focuses on the simulation of FTP-75 mode which is considered with spark timing control on transient condition. The acceleration is the most important factor for vehicle fuel economy. The retard of spark timing increases in proportion to acceleration. Likewise, bsfc(break specific fuel consumption) which is affected by spark timing also increases in proportion to acceleration. The result of simulation considered transient condition shows 0.3% of error comparing with a test on chassis-dynamometer.

• Nuclear Engineering and Technology
• /
• v.45 no.5
• /
• pp.581-588
• /
• 2013

This paper deals with the Safety Analysis for $CANDU^{(R)}$ 6 nuclear reactors as affected by main Heat Transport System (HTS) aging. Operational and aging related changes of the HTS throughout its lifetime may lead to restrictions in certain safety system settings and hence some restriction in performance under certain conditions. A step in confirming safe reactor operation is the tracking of relevant data and their corresponding interpretation by the use of appropriate thermal-hydraulic analytic models. Safety analyses ranging from the assessment of safety limits associated with the prevention of intermittent fuel sheath dryout for a slow Loss of Regulation (LOR) analysis and fission gas release after a fuel failure are summarized. Specifically for fission gas release, the thermal-hydraulic analysis for a fresh core and an 11 Effective Full Power Years (EFPY) aged core was summarized, leading to the most severe stagnation break sizes for the inlet feeder break and the channel failure time. Associated coolant conditions provide the input data for fuel analyses. Based on the thermal-hydraulic data, the fission product inventory under normal operating conditions may be calculated for both fresh and aged cores, and the fission gas release may be evaluated during the transient. This analysis plays a major role in determining possible radiation doses to the public after postulated accidents have occurred.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.719-724
• /
• 1998

A preliminary fuel channel analysis for 35% reactor inlet header (RIH) break in CANDU reactor loaded with the CANFLEX-RU fuel bundles has been performed. The predicted results are compared with those for the reactor compared with those for the reactor loaded with standard 37-element bundles. The maximum fuel centerline and sheath temperatures for the CANFLEX-RU bundle channel were lower by 338 and 122 $^{\circ}C$, respectively, than those for the standard bundle because of the Bower maximum linear power of the CANFLEX-RU bundle In spite of the 0.4 FPS higher power pulse of the CANFLEX-RU bundle case. Fuel integrity margin to fuel breakup for the CANFLEX-RU bundle is about 50 J/g higher than that for the standard bundle. The PT/CT contact for the CANFLEX-RU bundle occurred 2 s later than that for the standard bundle. The PT/CT contact temperature for the CANFLEX-RU bundle was 2 $^{\circ}C$ lower than that for the standard bundle. These provide the CANFLEX-RU bundle with the negligibly enhanced safety margin for the fuel channel integrity in CANDU 6 reactor, compared with the standard bundle.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.30-35
• /
• 2018

The objective of this study is to predict numerically the effect of intake humidification on the injected diesel fuel spray characteristics in a compression ignition engine. In this work, Wave model and Ducowicz model were applied as the break-up model and evaporation model, respectively. The amount of water vapor for the humidification was changed from 0% to 30% of injected fuel mass. The number of applied meshes was generated from 49,000 to 110,000. At the same time, the results of this work were compared in terms of spray tip penetration, SMD and equivalence ratio distributions. It was found that the cylinder temperature and cylinder pressure were decreased with increasing water vapor mass by vaporization latent heat and specific heat, however, the difference was very small. So, the spray tip penetration was not different by water vapor mass. Also, higher equivalence ratio distributions were observed with increasing water vapor mass by the improvement of fuel atomization.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3743-3747
• /
• 2011

Kinetic studies on the reactions of Y-S-aryl phenyl phosphonochloridothioates with X-pyridines have been carried out in MeCN at $55.0^{\circ}C$. The Hammett and Bronsted plots for substituent X variations in the nucleophiles are biphasic concave upwards with a break point at X = H. The Hammett plots for substituent Y variations in the substrates are biphasic concave upwards with a break point at Y = H, and the sign of ${\rho}_Y$ is changed from unusual negative (${\rho}_Y$ < 0) with the weaker electrophiles to positive (${\rho}_Y$ > 0) with the stronger electrophiles. The stepwise mechanism is proposed on the basis of the ${\rho}_X$, ${\beta}_X$, and ${\rho}_{XY}$ values as follows: a ratelimiting leaving group departure from the intermediate involving a frontside attack and product-like TS for the stronger nucleophiles and weaker electrophiles; a rate-limiting leaving group departure from the intermediate involving a backside attack and product-like TS for the weaker nucleophiles and electrophiles; a rate-limiting bond formation involving a frontside attack for the stronger nucleophiles and electrophiles; a rate-limiting bond formation involving a backside attack for the weaker nucleophiles and stronger electrophiles. The substituent effects of X and Y on the pyridinolysis mechanisms of $R_1R_2P$(=S)Cl-type substrates are discussed.