• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.36-42
• /
• 2019

The ESP (Electronic Stability Program) is an active control system that controls the posture of the vehicle by sensing the unstable state of the vehicle during braking, driving, or turning. The system works if the vehicle becomes unstable and it is very dangerous to develop it in the actual vehicle. For this reason, many studies have been carried out on the method of developing with simulation such as SIL / EIL. Some advanced companies have already applied it to the product development process. In this study, ESP hydraulic system and braking device model were constructed using SimulationX to build ESP SIL / EIL model. The hydraulic system model was constructed using the actual design parameters and the performance of the hydraulic model was verified by comparing with the actual vehicle test.

• 한국정밀공학회지
• /
• 제14권8호
• /
• pp.146-154
• /
• 1997

Solenoid-folw control type ABS is used with a 'dump and reapply' pressure control arrangement instead of using 2/2 (normal open/close) solenoid valves in convensional systems(sol. -sol. control type), a flow control valve is used which replaces the (no) inlet valve. The flow control valve controls fluid flow providing a nearly constant reapply rate( .theta. ) after the dump plase of ABS operation. In this study, to investigate a characteristics of brake pressure by PWM control, test rig was consisted of ABS hydraulic modulator, digital controller, pneumatic power supply and brake master cylinder. For comparison with experi- mental results, system modelling and computer simulation were performed. As a result, experiment results showed fairly agreement with the simulation. Also, it is shown that the pressure gradient (tan .theta. ) is affected by pressure, frequency, duty ratio and expressed with an exponential funtion.

• International Journal of Railway
• /
• 제2권2호
• /
• pp.70-79
• /
• 2009

An optimal driving strategy of a train in a long journey on a nonsteep track has four phases: an initial power phase, a long hold speed phase, a coast phase and a final brake phase. The majority of the journey is speed holding. On a track with steep gradients, it becomes necessary to vary the strategy around steep sections of track because it is not possible to hold a constant steep on steep track. Instead we must interrupt the speed hold phase with a power phase. The aim of this paper is to show that there is a unique power phase that satisfies the necessary conditions for an optimal journey. The problem is developed and solved for various cases, from a simple single steep gradient to a complicated multiple steep gradient section. For each case, we construct a set of new conditions for optimality of the power phase that minimises the energy used during the power phase subject to a weighted time penalty. We then use the new necessary conditions to develop a calculate scheme for finding an optimal power phase for a steep incline. We also present an example to confirm the uniqueness of an optimal power phase.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.342-344
• /
• 2008

24V DC power system of commercial vehicle includes 28V alternator and 24V battery bank (two 12V battery bank in series). BEQ(Battery Equalizer) provides efficient and reliable 12V DC power to 12V electrical load in 24V DC power system. In addition to providing 12V DC power, BEQ ensures that battery voltages remain equal which extends battery life. It is the most cost effective and efficient solution for dual voltage systems. BEQ made by Hyundai MOBIS is specifically designed to provide reliable 12V DC power for 12V ABS(Anti-lock Brake system).

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.103-111
• /
• 2008

One of the most popular internal combustion engines is the engine in the transportation device. Power is a parameter that shows the capabilities of an object that gives energy, for example the internal combustion engine. Power in this engine is measured by a device called dynamometer. The CFD (Computational Fluid Dynamic) fluent software was simulated several impeller variables to absorb power of engine. With that result, we knew the biggest dynamometer absorber power, cheapest and easy to be made. The hydraulic dynamometer is selected type of dynamometer as the result of design process. The basic principle of a hydraulic dynamometer is the same as centrifugal pump but it has low pump efficiency. The results of the test are maximum power and torque of the tested engine and the operation area of the selected hydraulic dynamometer.

• 한국농공학회지
• /
• 제18권4호
• /
• pp.4259-4264
• /
• 1976

This paper, is about the test on the operating performance of diesel engine by using of soybean oil which farmers could supply in their farm yard. The diesel engine used is a swirl-chamber type, four stroke cycle with single cylinder, air cooling and its rated horse power is 2 PS per 1300 rpm. Several results obtained are as follows; 1. The starting performance of diesel engine with soybean oil is almost the same as that with light oil. 2. The variation of engine speed according to various engine load is small when soybean oil is used compared with light oil. It is considered that soybean oil is desirable for the purpose of industerial power machine fuel. 3. The specific fuel consumption increases approximately 10 percent high in the condition of rated horse power and maximum horse power and shows less or same during the load test in low velocity, when soybean oil is used 4. Though the brake thermal efficiency in the condition of rated horse power and maximum horse power is inclined to decrease when soybean oil is used compared during the load test in low velocityt shows good inclination.

• International Journal of Automotive Technology
• /
• 제6권1호
• /
• pp.15-21
• /
• 2005

The purpose of this paper is to experimentally investigate the engine pollutant emissions and combustion characteristics of diesel engine fueled with ethanol-diesel blended fuel (bio-diesohol). The experiments were performed on a single-cylinder DI diesel engine. Two blend fuels were consisted of $15\%$ ethanol, $83.5\%$ diesel and $1.5\%$ solublizer (by volume) were evaluated: one without cetane improver (E15-D) and one with a cetane improver (E15-D+CN improver). The engine performance parameters and emissions including fuel consumption, exhaust temperature, lubricating oil temperature, Bosch smoke number, CO, NOx, and THC were measured, and compared to the baseline diesel fuel. In order to gain insight into the combustion characteristics of bio-diesohol blends, the engine combustion processes for blended fuels and diesel fuel were observed using an Engine Video System (AVL 513). The results showed that the brake specific fuel consumption (BSFC) increased at overall engine operating conditions, but it is worth noting that the brake thermal efficiency (BTE) increased by up to $1-2.3\%$ with two blends when compared to diesel fuel. It is found that the engine fueled with ethanol-diesel blend fuels has higher emissions of THC, lower emissions of CO, NOx, and smoke. And the results also indicated that the cetane improver has positive effects on CO and NOx emissions, but negative effect on THC emission. Based on engine combustion visualization, it is found that ignition delay increased, combustion duration and the luminosity of flame decreased for the diesohol blends. The combustion is improved when the CN improver was added to the blend fuel.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.9-17
• /
• 1994

In this study, a shifting algorithm of CVT was suggested for the two(2) driving modes : (1) power mode and (2) economy mode. Shifting algorithm must be obtained to make the engine run on the optimum operating line for the desired performance of the vehicle. Optimum operating lines of the engine were obtained by connecting the shortest way of the iso-power lines for the power mode and by connecting the shortest way of the BSFC curves for the economy mode. Also dynamic model of CVT vehicle was derived considering the throttle and the brake operation. By using the shifting algorithm and the CVT vehicle model, numerical simulations were performed to estimate the performance of CVT. Simulation results showed that comparing the performance of the conventional 4-speed automatic transmission, acceleration performance of the CVT vehicle was almost same with the AT vehicle for the power mode and the fuel economy of CVT was 14% superior than that of AT for the economy mode.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1327-1331
• /
• 2004

In this paper constant power models for electric trains have been used to analyze the steady states of the AT feeding systems. There are some previous studies utilizing constant impedance models or constant current models. These mentioned models are easy to use, but even so they don't yield exact results because of the innate restraints of the models since linear models cannot represent the characteristic of constant power in inverter-driven trains. It is reasonable that the train be considered as a constant load model when it drives or as a constant source model when it applies regenerative brake. Nonlinear equations which reflect constant power model for train have been developed by considering mutual impedances between wires and AT's turn-ratio of 1:1, then these equations have been solved by N-R iterative method. The proposed method doesn't need any specific assumptions through either the process of developing equations or the process of acquiring solutions, so it can be said to be stricter than other conventional methods.

• 대한토목학회논문집
• /
• 제30권6D호
• /
• pp.587-597
• /
• 2010

교통사고가 발생하면 사고 당사자들은 민 형사적인 문제에서 자유롭지 못하기 때문에, 교통사고 조사자는 사고 상황을 정확하게 재현 또는 분석을 하여야 한다. 또한, 이러한 교통사고 발생과 관련한 요인에 대한 분석을 통해 얻어진 자료를 활용하여 교통사고 다발지역의 개선 및 보완작업을 시행하게 된다. 현재까지 알려진 바로는 수많은 교통사고, 교통시설물, 도로설계 등과 관련하여 가장 많은 영향을 미치는 요인은 차량의 속도와 가속능력, 제동능력 등이다. 이는 자동차의 성능과 노면의 마찰계수가 가장 밀접한 영향을 미치는 부분이다. 특히, 사고 순간의 속도의 추정은 교통사고처리특례법의 11개 주요항목인 과속과 관련하여 매우 중요한 사항이기에 정확성이 요구되는 부분이다. 하지만, 국내에서는 아직 이러한 부분에 대한 심도 있는 연구가 많이 진행되지 못하는 것이 현실이다. 이러한 현실을 반영하여 본 연구에서는 차량의 급제동에서 제동흔적이 발생되기 시작할 때까지의 시간인 제동경과시간을 정밀가속도계(Vericom VC2000PC)로 측정하여 제동경과시간과 노면의 마찰계수를 정확히 추정하였다. 실험결과를 분석하여, 여러 가지 특수 아스팔트 포장 및 미끄럼방지포장 종류에 따른 제동경과시간과 마찰계수를 계산하여 연구의 목적에 맞도록 기초자료를 제공하고자 하였다.