• 수산해양기술연구
• /
• 제42권2호
• /
• pp.111-118
• /
• 2006

It is indispensable to grasp the turning ability of a ship to operate her effectively. For this purpose, the author measured the turning ability of training ship, A-RA by use of bow thruster and stem rudder. The turning ability of this ship, in case of using both of stem rudder and bow thruster at the same time, caused by increase of steering angle provides more influence to the size of tactical diameter than it caused by the power of bow thruster. But the influence of bow thruster on the turning ability is available only within rudder angle $5^{\circ}\;-\;10^{\circ}$, so it is possible to grasp that the effect of bow truster is reduced as rudder angle become bigger. In case of the influence of bow thruster by her speed, the ability of bow thruster is very effective at low speed, but it is almost not available in normal turning speed. Therefore, the using both of stem rudder and bow thruster can be useful in case of low speed proceeding at entrance or departure of the narrow waterway or inside port which sea traffic is congest for collision avoidance.

• 대한조선학회논문집
• /
• 제57권1호
• /
• pp.52-59
• /
• 2020

This study aims to investigate the bow thruster performance of the research vessel "NARA" by full-scale maneuvering trials. The thruster test method refers to ITTC's recommended procedures and guidelines. Turning tests with the bow thruster are performed at speed conditions of 0, 2, and 4 knots. The test results indicate that the Rate of Turn (ROT) increased when the ship is in a higher speed condition. Due to the position of the propeller and the housing of the bow thruster, there is difference in the efficiency of the bow thruster according to the turning direction. Zigzag tests with the bow thruster were conducted at speed conditions of 2 and 4 knots. At speeds above 4 knots, it seems difficult to change the course only with the bow thruster.

• 한국기계연구소 소보
• /
• 제4권2호
• /
• pp.41-48
• /
• 1982

• 대한조선학회논문집
• /
• 제43권3호
• /
• pp.304-312
• /
• 2006

For protection of the thruster against mechanical damage and reduction of tunnel resistance at ship forward speed, the tunnel grids are normally installed. Some of ship operators however, have a strong distrust of the protective function of the tunnel grids and so they do not want to install the protective grids for higher thruster efficiency. Since the grids should be installed at very close to the side shell as far as possible in due consideration of flow direction to minimize additional resistance induced by tunnel openings, it has been too hard and time consuming work to install the grids on the curved and chamfered tunnel entrances considering its relatively low resistance reduction effect. DSME (Daewoo Shipbuilding & Marine Engineering Co., Ltd) developed a substituting device named TG (Tunnel Guides) for bow thruster tunnel grids which is characterized by higher resistance reduction, higher thruster efficiency and easy to installation. This paper provides the principle idea of the TG with short history of the development using CFD calculations and model experiments in MOERI (former KRISO).

• 대한조선학회논문집
• /
• 제41권1호
• /
• pp.40-46
• /
• 2004

In this paper, one of the harbour manoeuvring tests is described. its goal is to investigate the so-called crabbing performance of ships. By crabbing is meant the ability of the vessel to move sideways with the use of her own manoeuvring devices like propellers, rudders, transverse thruster, etc. The crabbing model tests were carried out in the Ocean Engineering Wide Tank, University of Ulsan(UOU) to measure the transverse forces and yawing moments by the transverse thruster alone and the propeller-rudder arrangement in combination with the bow thruster. The comparison between UOU crabbing test results and data measured at one of foreign research institutes showed a little gap due to different rotating conditions of controllable pitch propellers.

• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.327-332
• /
• 2012

International Towing Tank Conference (ITTC) recommended verifying a ship's ability to move transversely at zero forward speed without altering heading by a crabbing test. In sea trial, all available propellers/rudders/thrusters should be used to find the maximum possible transverse speed. For estimating crabbing ability in the design stage, tests to estimate possible swaying force and yawing moment range using all available propellers/rudders/thrusters are conducted. By butterfly diagram, which compares possible swaying force and yawing moment range with external swaying force and yawing moment by wind, a ship's crabbing ability can be estimated. In this study, model tests of a cruise vessel equipped with bow thrusters and POD system were conducted to find out her crabbing ability in the design stage. To mimic quay condition, a model quay-wall was set in the towing tank.

• 한국항해항만학회지
• /
• 제34권8호
• /
• pp.629-634
• /
• 2010

세계 컨테이너 물동량의 증가와 컨테이너선의 대형화로 인해 선박과 수심이 얕은 항구 및 부두를 연결하는 새로운 개념의 해상 운송 수단이 요구되어 왔다. 본 연구에서는 모바일하버 선형과 함께, Azipod 추진기 및 선수 스러스터(Bow thruster) 등으로 구성된 모바일하버의 조종수학모델을 구축하였다. 그리고 선체 유체력 및 Azipod 추력 등을 평가 적용하여 조종운동 시뮬레이션을 수행하였다. 그 결과, 모바일 하버의 조종운동 시뮬레이션에 의한 선회성능과 조종제어범위를 사전에 예측할 수 있었다. 또한, 모바일하버의 직진 시험 및 선회성능 시험에 있어 양호한 결과를 얻었으며, 접안 시 Azipod 추진기와 선수 스러스터를 이용한 최적의 조종운동 시뮬레이션을 확립하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권3호
• /
• pp.199-210
• /
• 2012

The recent researches on the automatic berthing control problems have used various kinds of tools as a control method such as expert system, fuzzy logic controllers and artificial neural network (ANN). Among them, ANN has proved to be one of the most effective and attractive options. In a marine context, the berthing maneuver is a complicated procedure in which both human experience and intensive control operations are involved. Nowadays, in most cases of berthing operation, auxiliary devices are used to make the schedule safer and faster but none of above researches has taken into account. In this study, ANN is applied to design the controllers for automatic ship berthing using assistant devices such as bow thruster and tug. Using back-propagation algorithm, we trained ANN with set of teaching data to get a minimal error between output values and desired values of four control outputs including rudder, propeller revolution, bow thruster and tug. Then, computer simulations of automatic berthing were carried out to verify the effectiveness of the system. The results of the simulations showed good performance for the proposed berthing control system.

• 수산해양기술연구
• /
• 제54권2호
• /
• pp.181-187
• /
• 2018

In order for the probe to perform ocean exploration and survey research, it is necessary to adjust the position of the ship as desired by dynamic positioning system. The dynamic positioning system of T/S NARA is applied to K-POS dynamic positioning system of Kongsberg, which makes maintaining the ship's position, changing position and heading control possible. T/S NARA is not capable of dynamic positioning if one or more propulsive forces are lost with DP Level One. However, it is predicted that dynamic positioning can be achieved even at the time of missing one thrust in a good sea condition. Therefore, we want to analyze the effect of each propulsion on the performance of dynamic position system. When one of the bow thruster and azimuth thrusters lost their propulsion, maintaining the ship's position, changing position and heading control performance were compared and analyzed. If the situation occurred disable from using the bow thruster, they can not maintain ship's position. Azimuth thruster was influential for the ship's position control and bow thruster was influential in heading control. The excellent dynamic positioning performance can be achieved, considering the propulsion power that will have a impact on each situation in the future.

• Journal of Advanced Research in Ocean Engineering
• /
• 제3권3호
• /
• pp.102-111
• /
• 2017

This study considered the effects on the seabed of a harbor and quay wall from ship maneuvers in relation to the thruster jet flow and initial velocity. This study also included the engine capacity, RPM, and diameter and pitch of a ship's thruster for a required speed. The impact of a scour hole on the environment of a quay wall was investigated. Based on these results, a risk based analysis was conducted to evaluate different strategies and their consequences. There has been an increase in the loads on the bottom of a harbor during ship maneuvering. This increase is caused by the propeller loads of mooring and unmooring vessels. This indicates a greater number of arrivals and departures of vessels with larger drafts, larger thruster diameters, and larger available thruster power capacities. Another important cause could be an increase in the maneuverability of vessels from the use of bow thrusters. The increasing loads, which cause a higher jet flow above the bottom, can lead to undesirable scour holes.