• Advances in nano research
• /
• v.14 no.3
• /
• pp.285-294
• /
• 2023

The dynamic and sensing performances of nanomechanical resonators with their different boundary conditions are studied based on surface elasticity-based modeling and simulation. Specifically, the effect of surface stress is included in Euler-Bernoulli beam model for different boundary conditions. It is shown that the surface effect on the intrinsic elastic property of nanowire is independent of boundary conditions, while these boundary conditions affect the frequency behavior of nanowire resonator. The detection sensitivity of nanowire resonator is remarkably found to depend on the boundary conditions such that double-clamping boundary condition results in the higher mass sensitivity of the resonator in comparison with simple-support or cantilever boundary condition. Furthermore, we show that the frequency shift of nanowire resonator due to mass adsorption is determined by its length, whereas the frequency shift is almost independent of its thickness. This study enables a design principle providing an insight into how the dynamic and sensing performances of nanomechanical resonator is determined and tuned.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1361-1363
• /
• 1998

Poly-Si grain boundaries act as potential barriers as well as recombination centers for the photo-generated carriers in solar cells. Thereby, grain boundaries of poly-Si are considered as a major source of the poly-Si cell efficiency was reduced This paper investigated grain boundary effect of poly-Si wafer prior to the solar cell fabrication. By comparing I-V characteristics inner grain, on and across the grain boundary, we were able to detect grain potentials. To reduce grain boundary effect we carried out pretreatment, $POCl_3$ gettering, and examined carrier lifetime. This paper focuses on resistivity variation effect due to grain boundary of poly-Si. The resistivity of the inner grain was $2.2{\Omega}-cm$, on the grain boundary$2.3{\Omega}-cm$, across the grain boundary $2.6{\Omega}-cm$. A measured resistivity varied depending on how many grains were included inside the four point probes. The resistivity increased as the number of grain boundaries increased. Our result can contribute to achieve high conversion efficiency of poly-Si solar cell by overcoming the grain boundary influence.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.911-912
• /
• 2010

• Smart Structures and Systems
• /
• v.18 no.6
• /
• pp.1087-1109
• /
• 2016

In this manuscript, the small scale and thermal effects on vibration behavior of preloaded nanobeams with non-ideal boundary conditions are investigated. The boundary conditions are assumed to allow small deflections and moments and the concept of non-ideal boundary conditions is applied to the nonlocal beam problem. Governing equations are derived through Hamilton's principle and then are solved applying Lindstedt-Poincare technique to derive fundamental natural frequencies. The good agreement between the results of this research and those available in literature validated the presented approach. The influence of various parameters including nonlocal parameter, thermal effect, perturbation parameter, aspect ratio and pre-stress load on free vibration behavior of the nanobeams are discussed in details.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.403-407
• /
• 2009

It is reported that the heavy weight floor impact noise of a slab system is very sensitive to the location of microphone and impact load. In addition, it is known that the aspect raio, thickness and boundary condition of a slab also have great effect on the noise induced by impact load. However, the effect has been mainly evaluated by experimental test and numerical analysis is nearly performed to verify the effect quantitatively. In this study, the effect of the aspect ratio, thickness and boundary condition on the heavy weight floor impact noise is examined through numerical analysis for simple rectangular slab system. The results show that the thickness and boundary condition have a strong correlation with the noise of the slab, on the contrary, the aspect ratio has little relation with the noise.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.165-169
• /
• 2009

The effect of the Dirichlet boundary condition for the redistance equation of level set method on the solutionof sloshing problem is investigated by adopting four Dirichlet boundary conditions. For the solution of the incompressible Navier-Stokes equations, P1P1 four-step fractional finite element method is employed and a least-square finite element method is used for the solutions of the two hyperbolic type equations of level set method; advection and redistance equation. ALE (Arbitrary Lagrangian Eulerian) method is used to deal with a moving computational domain. It has been shown that the free surface motion in a sloshing tank is strongly dependent on the type of the Dirichlet boundary condition and the results of broken dam and sloshing problems using various Dirichlet boundary conditions are discussed and compared with the existing experimental results.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.277-284
• /
• 1996

The water test results indicated that the impurities had detrimetal effect on the wear resistance of silicon nitride and the effects were getting severe as the temperature increased. Especially when Ca existed as an impurity the detrimental effects was the most severe. These results were resulted from the fact that impurities lowered the mechanical properties of the grain boundary phase of silicon nitride. The wear test results of glass/glass-ceramic specimens having a similar composition to the grain boundary phase of silicon nitride revea-led that the specimen containing CaO showed the lowest wear resistance. The existence of Fe and Ca at the grain boundary phase assisted forming a grain boundary phase with relatively low refractoriness. Therefore at a given wear condition the removal of deformed layer would be easier. The results showed that the glass phases could be modified by heat-treatment and this modification improved tribological characteristics of the silicon nitride.

• Journal of Environmental Science International
• /
• v.10 no.5
• /
• pp.329-336
• /
• 2001

Characgcteristics of nocturnal boundary layer(NBL) were analyzed by the upper-air observations data using with the airsonde and pilot balloons from 1994 to 1999 in Kyungpook province. The automate weather boundary layer can become stably stratified when the surface is cooler than the air. Stable nocturnal boundary layer height were estimated from the top of surface stable layer where the vertical gradient of temperature and mixing ratio tend to zero or negative. The depth of the stable nocturnal boundary layer depended largely on the thermal effect rather than the wind effect at nighttime. The NBL was more developed on the land than on the coastal region. The stability index (bulk Richardson number) showed that the NBL was stable when the wind was weak and the vertical gradient of the temperature was strong. The heat budget in the NBL was studied by considering the effect of the radiative and the cooled by both the longwave radiative flux and the divergence of the heat flux, while NBL under the cloudy sky the longwave radiative flux played a role of the warming. It was noted that the heat was not conserved in both cases. To complete the heat budget in the NBL the warming/cooling by advection and subsidence must be considered.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.173-173
• /
• 2015

The flood water level in tidal river is determined by the joint effects of flood discharge and tidal water levels at downstream boundary. Due to the variable tidal boundary conditions, the evaluated design water levels associated with a certain flood event can be significantly different. To avoid determining of design water levels just by a certain tidal boundary condition and remove the influence of variability in boundary condition from the evaluation of design water levels, a probabilistic approach is considered in this study. This study focuses on the development of a method to evaluate the realistic design water levels in tidal river with taking into account the combined effects of river discharge and tidal level. The flood water levels are described by the joint probability of two driving forces, river discharge and tidal water levels. The developed method is applied to determine design water levels for the tidal reach of the Han River. An unsteady flow model is used to simulate the flow in the reach. To determine design water levels associated with a certain flood event, first, possible boundary conditions are obtained by sampling starting times of tidal level time series; then for each tidal boundary condition, corresponding peak water levels along the channel are computed; and finally, design water levels are determined by computing the expectations of the peak water levels. Two types of tides which are composed by different constituents are assumed (one is composed by $M_2$, and the other one is composed by $M_2$ and $M_2$) at downstream boundary, and two flood events with different maximum flood discharges are considered in this study. It is found that (a) the computed design water levels with two assumed tides have no significant difference for a certain flood event, though variability of peak water levels due to the tidal effect is considerably different; (b) tidal effect can reach to the Jamsil submerged weir and the effect is obvious in the downstream reach of the Singok submerged weir; (c) in the tidally affected reach, the variability of peak water levels due to the tidal effect is greater if the maximum flood discharge is smaller.

• Smart Structures and Systems
• /
• v.22 no.5
• /
• pp.621-630
• /
• 2018

Boundary effect and the noise robustness are the two crucial aspects which affect the effectiveness of the damage localization based on the mode shape measurements. To overcome the boundary effect problem and enhance the noise robustness in damage detection, a simple damage localization method is proposed based on the Singular Value Decomposition (SVD) for the mode shape of composite plates. In the proposed method, the boundary effect problem is addressed by the decomposition and reconstruction of mode shape, and the noise robustness in enhanced by the noise filtering during the decomposition and reconstruction process. Numerical validations are performed on plate-like structures for various damage and boundary scenarios. Validations show that the proposed method is accurate and effective in the damage detection for the two-dimensional structures.