• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.330-334
• /
• 2004

A new SEPIC-Flyback converter is proposed. The proposed converter is the integration of SEPIC and Flyback converter. Not only SEPIC output but also Flyback output could be fully regulated by constant frequency PWM control. Merged SEPIC and Flyback topology can share the transformer and power MOSFET. When the switch turns on, one topology operates via capacitive energy transfer. The other topology acts as inductive energy transfer while the switch is off. So, it can increase power density per one cycle. The experimental result is presented and verified.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.677-687
• /
• 2018

This paper presents a novel power decoupling control scheme with the bidirectional buck-boost converter for primary-side regulation photovoltaic (PV) micro-inverter. With the proposed power decoupling control scheme, small-capacitance film capacitors are used to overcome the life-span and reliability limitations of the large-capacitance electrolytic capacitors. Then, an improved flyback PV inverter is employed in continuous conduction mode with primary-side regulation for the PV power conditioning. The proposed power-decoupling controller shares the reference for primary side current regulation of the flyback PV inverter. The decoupling controller shapes the input current of the bidirectional buck-boost converter. The shared reference eliminates the phase-delay between the input current to the bidirectional buck-boost converter and the double frequency current at the PV primary current. The elimination of the phase-delay in dynamic response enhances the ripple rejection capability of the power decoupling buck-boost converter even with small film capacitor. With proposed power decoupling control scheme, the additional advantage of the primary-side regulation of flyback PV inverter is that there is no need to have an extra current sensor for obtaining the ripplecurrent reference of the decoupling current-controller of the power-decoupling buck-boost converter. Therefore, the proposed power decoupling control scheme is cost-effective as well as the size benefit. A new transient analysis is carried out which includes the source voltage dynamics instead of considering the source voltage as a pure voltage source. For verification of the proposed control scheme, simulation and experimental results are presented.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.8
• /
• pp.392-401
• /
• 2001

This paper presents the single-stage high power factor AC to DC converter operated in active-clamp mode. The proposed converter is added active-clamping circuit to boost-flyback single-stage power factor corrected power supply. The active-clamping circuit limits voltage spikes, recycles the energy trapped in the leakage inductance, and provides a mechanism for achieving soft switching of the electronic switches to reduce the switching loss. The auxiliary switch of active-clamping circuit uses the same control and driver circuit as the main switch to reduce the additional cost and size. To verify the performance of the proposed converter, a 100W converter has been designed. The proposed converter gives good power factor correction, low line current harmonic distortions, and tight output voltage regulation, as used unity power factor.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.212-219
• /
• 2002

A novel mode of parallel operation of a modular 3-phase AC-DC flyback converter for power factor correction along with tight regulation was recently analyzed and presented. The advantage of the proposed converter does not require expensive high voltage and high current devices that are normally needed in popular boost type 3-phase converter. In this paper tile detailed small signal analysis of the modular 3-phase AC-DC flyback converter is provided for control purpose and also experimental results are included to confirm the validity of the analysis.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.2
• /
• pp.159-165
• /
• 1999

Three-phase AC-DC flyback converter with high power factor correction and tight regulation is presented in this p paper. The advantage of the proposed converter does not require expensive high voltage and high cun‘ent devices that a are normally needed in popular boost type 3-phase converter. In this paper the detailed small signal analysis of the m modular 3-phase AC-DC flyback converter is provided for control purposes and also experimental results are included t to confirm the validity of the analysis.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.467-472
• /
• 2005

In this paper, design and control of the novel SEPIC-Flyback converter(SF converter) is developed as a possible converter for fuel cell system. This output characteristic of SF converter is similar to Buck-Boost converter in that it can step-up or step-down the voltage. With the small signal equivalent circuit modeling of SF converter, control-to-output transfer function is obtained. SF converter couples up the inductive type converter to capacitive type converter with one transformer, which has less ripple current than its respective one does. To verify the validity of the proposed converter, 500W, 100kHz converter is designed and tested. ZVS switching and active clamping are also tested in practice.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.187-189
• /
• 2003

Conventional Switched Mode Power Supplies(SMPS) with diode-capacitor rectifier have distorted input current waveform with high harmonic content. Typically, these SMPS have a power factor lower than 0,65. To improve with this problem the power factor correction(PFC) circuit of power supplies has to be introduced. Specially. to the reduce size and manufacture cost of power conversion device, the single-stage PFC converter is increased to demand as necessary of study. in this paper, The comparative analysis of power factor correction circuit using Feedforward control with average current mode flyback converter(single-stage) and boost converter(two-stage). Also, the validity of designed and manufactured high power factor flyback converter and boost converter is confirmed by simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.119-123
• /
• 2001

In this paper, a DCM operated boost integrated single-stage forward-flyback converter is proposed. This proposed converter has high power factor, low harmonic distortion, and tight output regulation. To increase efficiency, zero voltage switching with asymmetrical control is used. This converter also give low voltage stress in switch and this results in low conduction loss with low turn-on resistance.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.109-111
• /
• 1998

A novel mode of parallel operation of 3-phase AC-DC flyback converter for power factor correction along with tight regulation was recently analyzed and presented. The advantage of the proposed converter does not require expensive high voltage and high current devices that are normally needed in popular boost type 3-phase AC-DC flyback converter is provided for control purposes and also experimental results are included to confirm the validity of the analysis.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.175-181
• /
• 2016

In the conventional E-bike, a 42 V/10 A Li-ion battery drives a 24 V/10 A BLDC motor via a 6-switch PWM DC/AC inverter. The major problems of the conventional battery-fed motor drive systems are listed as follows. To charge the battery, an external battery charger (adapter) is required, which degrades the portability of E-bike users. In addition, given the high-frequency operation of the motor drive inverter, the switching losses are significant, which degrades the whole power efficiency. High-voltage batteries (42 V) require a complex battery management system (BMS), which degrades the reliability of the battery pack. In this paper, an embedded boost-converter battery charger for E-bikes is proposed. The variable output boost converter, which converts 16.8 V battery voltage to the required variable voltage of the inverter input, can use a low-voltage battery and thus improve the reliability of batteries. By varying the inverter input voltage via boost converter, a DC link voltage control method can be applied to reduce the switching frequency of the inverter, which improves the whole power efficiency. Given that the function of a flyback charger is integrated in the proposed boost converter, the portability of the E-bike user can be maximized by excluding an external adapter. The validity of the proposed circuit will be confirmed by operation mode analysis and simulation. Moreover, experimental results of integrative charger using Li-ion battery and 200 W motor test will be showed with a prototype sample as well.