• 제목/요약/키워드: Bolted angle connection

검색결과 17건 처리시간 0.02초

오스테나이트계 스테인레스강(STS304) 앵글 볼트 접합부의 구조적 거동에 관한 실험적 연구 (An Experimental Study on Structural Behavior of Bolted Angle Connections with Austenitic Stainless Steel)

  • 김민성;김태수;김승훈;이용택
    • 한국강구조학회 논문집
    • /
    • 제23권1호
    • /
    • pp.29-39
    • /
    • 2011
  • 강구조물에서 접합부의 구조적 거동을 파악하기 위해서 국내외에서 많은 이론과 실험을 통한 연구가 진행되고 있다. 특히, 국내에서는 탄소강 ㄱ형강의 블록전단파단과 전단지체현상 등에 대한 연구가 수행되어 왔다. 본 연구에서는 오스테나이트계 스테인레스강 앵글의 하중방향의 연단거리와 볼트배열(1행 1열,1행 2열)을 주요변수로 실험체를 계획하여, 앵글 볼트 접합부의 파단형태와 면외변형의 영향을 조사한다. 또한, 현행 기준식에 의한 예측결과와 실험결과의 파단양상과 최대내력을 비교하고 면외변형으로 인한 내력저하정도를 평가한다.

외부마감재가 부착된 볼트접합 방식 패널링 시스템의 내진성능평가를 위한 진동대 실험 (Shake Table Test on Seismic Performance Evaluation of the Bolted Connection Type Paneling System with Exterior Finish Material)

  • 오상훈;박종원;박해용
    • 한국지진공학회논문집
    • /
    • 제22권1호
    • /
    • pp.23-32
    • /
    • 2018
  • In this study, we conducted a shake table test to verify the seismic performance of the paneling system with steel truss composed of bolt connections. The control group was set to the traditional paneling system with steel truss connected by spot welding method. Test results showed that the bolted connection type paneling system has excellent deformation capacity without cracking or brittle fracture of the steel truss connection parts compared to the welding type paneling system. Furthermore, in the bolted connection type, slight damage occurred at the time of occurrence of the same story drift angle as compared with the existing method, it is considered that it has excellent seismic performance. In compliance with the performance-based design recommended for the current code (ASCE 41-13) on non-structural components, it is judged that in the case of the bolted connection type paneling system, it can be applied to all risk category structures without restriction. However, in the case of traditional paneling system with spot welding method, it is considered that it can be applied limitedly.

CFT 각형 기둥-보 합성 반강접 접합부의 단조가력 실험 (Monotonic Loading Test for CFT Square Column-to-Beam Partially Restrained Composite Connection)

  • 최성모;박수희;박영욱;김진호
    • 한국강구조학회 논문집
    • /
    • 제17권3호통권76호
    • /
    • pp.325-335
    • /
    • 2005
  • 본 연구의 목적은 CFT각형기둥과의 접합에 성능이 개선된 합성 반강접 접합디테일을 제안하고 기둥-보 접합부의 단조가력시 역학적 거동을 보기 위함이다. 극한 거동에 결정적 영향을 끼치는 하부 접합부의 전단내력을 보강하고 시공성을 고려하여 합성 반강접 접합을 CFT구조 형식에 시도하여 CFT기둥-보 접합부의 접합디테일을 제안하였다. 본 연구에서 제안하는 하부 보 플랜지 용접접합(M-2)을 기존 합성 반강접 접합상세인 시트앵글접합(M-1)과 비교/검토하였다. 두 개의 실대형 CFT기둥-보 합성 반강접 접합부 실험체에 대한 단조가력실험을 수행하였다. 실험 결과, 제안형인 하부 보플랜지 용접접합된 실험체는 강접합된 철골보의 약 85%의 강성을 확보하였다. 이는 기존형 실험체와 거의 동일하였으며, 반강접으로 분류됨을 확인할 수 있었다. 제안형 실험체가 웨브 접합부에서 볼트지압에 의한 전단파괴가 발생하였으나 파단 직전까지는 슬래브 연성파괴가 일어난 기존형 실험체와 유사한 거동을 보였다. 슬래브 보강근에 의해 충분한 강성 및 내력이 확보되며, 웨브부분의 강관내의 앵커보강에 의해 전소성모멘트에 상응하는 내력 및 변형성능이 확보되어 충분한 연성거동을 보이는 것으로 판단된다.

Shear lag coefficient of angles with bolted connections including equal and different legs through finite element method

  • Shahbazi, Lida;Rahimi, Sepideh;Hoseinzadeh, Mohamad;Rezaieaan, Ramzan
    • Structural Engineering and Mechanics
    • /
    • 제81권4호
    • /
    • pp.493-502
    • /
    • 2022
  • Shear lag phenomenon has long been considered in numerous structural codes; however, the AISC provisions have now no longer proposed any unique equation to calculate the shear lag ratio in bolted connections for angles in general. It is noticeable that, however, codes used in this case are largely conservative and need to be amended. A parametric study consisting of 27 angle sections with equal legs and different with bolted connections was performed to investigate the effects of shear lag on the ultimate tensile capacity of angle members. The main parameters were: steel grade, connection length and eccentricity from the center of the plate, as well as the number of rows of bolts parallel to the applied force. The test results were compared with the predictions of the classical 1-x/l law proposed by Mons and Chesen to investigate its application to quantify the effect of shear lag. A parametric study was performed using valid FE models that cover a wide range of parameters. Finally, based on the numerical results, design considerations were proposed to quantify the effect of shear lag on the ultimate tensile capacity of the tensile members.

Cyclic behavior of steel beam-to-column connections with novel strengthened angle components

  • Kang, Lan;Zhang, Cheng
    • Steel and Composite Structures
    • /
    • 제42권6호
    • /
    • pp.791-804
    • /
    • 2022
  • As a type of semi-rigid connection, the top and seat angle connections are popular in current structures owing to their good cyclic performance and simple erection. However, their stiffness and load bearing capacity are relatively insufficient. This study proposes two strengthening methods to further increase the stiffness and strength of bolted-angle joints while maintaining satisfactory energy dissipation capacity (EDC) and ductility. Cyclic loading tests were conducted on six joint specimens with different strengthened angle components. Based on the test results, the influence of the following important factors on the cyclic behavior of steel joint specimens was investigated: the position of the rib stiffeners (edge rib stiffeners and middle rib stiffener), steel strength grade of rib stiffeners (Q345 and Q690), and additional stiffeners or not. In addition, the finite element models of these specimens were built and validated through a comparison of experimental and numerical results. The stiffness and bearing capacity of the bolted-angle joints could be improved significantly by utilizing the novel strengthened joints proposed in this study. Moreover, this can be achieved with almost no increase in the amount of steel required, and the EDC of this joint could also satisfy the requirements of seismic codes from various countries.

Behaviour of bolted connections in concrete-filled steel tubular beam-column joints

  • Beena, Kumari;Naveen, Kwatra;Shruti, Sharma
    • Steel and Composite Structures
    • /
    • 제25권4호
    • /
    • pp.443-456
    • /
    • 2017
  • Many authors have established the usefulness of concrete filled steel tubular (CFST) sections as compression members while few have proved their utility as flexural members. To explore their prospective as part of CFST frame structures, two types of connections using extended end plate and seat angle are proposed for exterior joints of CFST beams and CFST columns. To investigate the performance and failure modes of the proposed bolted connections subjected to static loads, an experimental program has been executed involving ten specimens of exterior beam-to-column joints subjected to monotonically increasing load applied at the tip of beam, the performance is appraised in terms of load deformation behaviour of joints. The test parameters varied are the beam section type, type and diameter of bolts. To validate the experimental behaviour of the proposed connections in CFST beam-column joints, finite element analysis for the applied load has been performed using software ATENA-3D and the results of the proposed models are compared with experimental results. The experimental results obtained agree that the proposed CFST beam-column connections perform in a semi-rigid and partial strength mode as per specification of EC3.

Effect of connection modeling on the seismic response of steel braced non-moment resisting frames

  • Bagheri, Saman;Tabrizi, Navid Vafi
    • Structural Engineering and Mechanics
    • /
    • 제68권5호
    • /
    • pp.591-601
    • /
    • 2018
  • Non-moment beam-to-column connections, which are usually referred to as simple or shear connections, are typically designed to carry only gravity loads in the form of vertical shears. Although in the analysis of structures these connections are usually assumed to be pinned, they may provide a small amount of rotational stiffness due to the typical connection details. This paper investigates the effects of this small rotational restraint of simple beam-to-column connections on the behavior and seismic response of steel braced non-moment resisting frames. Two types of commonly used simple connections with bolted angles, i.e., the Double Web angle Connection (DWC) and Unstiffened Seat angle Connection (USC) are considered for this purpose. In addition to the pinned condition - as a simplified representation of these connections - more accurate semi-rigid models are established and then applied to some frame models subjected to nonlinear pushover and nonlinear time history analyses. Although the use of bracing elements generally reduces the sensitivity of the global structural response to the behavior of connections, the obtained results indicate considerable effects on the local responses. Namely, our results show that consideration of the real behavior of connections is essential in designing the column elements where the pin-connection assumption significantly underestimates design of outer columns of upper stories.

더블앵글로 접합된 골조의 수평처짐 (Story Drift of a Frame with Column Flange Bolted-Beam Web Welded Double Angle Connections)

  • 양재근;김호근;김기환
    • 한국공간구조학회논문집
    • /
    • 제3권3호
    • /
    • pp.95-103
    • /
    • 2003
  • Frame is one of the most commonly used structural systems for the resistance of applied loads. Many researchers have recently conducted their studies to investigate the effect of several parameters such as the connection flexibility, boundary condition of each support, beam-to-column stiffness ratio. These parameters play important roles on the characteristic behavior of frames. A simplified spring model is proposed to obtain the story drifts of frames with various beam-to-column connection stiffnesses in this research. A point bracing system with adequate spring stiffness is also suggested to establish the relationship between the applied load and the resisting translational spring stiffness within the limit state of story drift.

  • PDF

An improved polynomial model for top -and seat- angle connection

  • Prabha, P.;Marimuthu, V.;Jayachandran, S. Arul;Seetharaman, S.;Raman, N.
    • Steel and Composite Structures
    • /
    • 제8권5호
    • /
    • pp.403-421
    • /
    • 2008
  • The design provisions for semi-rigid steel frames have been incorporated in codes of practice for steel structures. In order to do the same, it is necessary to know the experimental moment-relative rotation (M-${\theta}_r$) behaviour of beam-to-column connections. In spite of numerous publications and collection of several connection databases, there is no unified approach for the semi-rigid design of steel frames. Amongst the many connection models available, the Frye-Morris polynomial model, with its limitations reported in the literature, is simple to adopt at least for the linear design space. However this model requires more number of connection tests and regression analyses to make it a realistic prediction model. In this paper, 3D nonlinear finite element (FE) analysis of beam-column connection specimens, carried out using ABAQUS software, for evaluating the M-${\theta}_r$ behaviour of semi-rigid top and seat-angle (TSA) bolted connections are described. The finite element model is validated against experimental behaviour of the same connection with regard to their moment-rotation behaviour, stress distribution and mode of failure of the connections. The calibrated FE model is used to evaluate the performance of the Frye-Morris polynomial model. The results of the numerical parametric studies carried out using the validated FE model have been used in proposing modifications to the Frye-Morris model for TSA connection in terms of the powers of the size parameters.

유리섬유 보강집성재 볼트 접합부 전단내력 예측 (Estimate of Bolt Connection Strength of Reinforced Glulam using Glass Fiber)

  • 김건호;홍순일
    • Journal of the Korean Wood Science and Technology
    • /
    • 제44권1호
    • /
    • pp.67-74
    • /
    • 2016
  • 유리섬유 보강집성재의 볼트접합부 항복전단내력을 예측하기 위해 인장형 전단시험을 통해 측정된 실측값과 설계기준에 의한 예측값을 비교하였다. 볼트접합부의 항복전단내력 예측식을 위해 층재의 방향별 탄성계수, 포아송비, 전단계수를 측정하였다. 설계기준의 예측식 보정을 위해 유리섬유 보강집성재의 파괴거동을 반영한 파괴인성계수($K_{ft}$)를 적용하여 보정항복전단내력을 비교하였다. 층재의 탄성계수는 섬유방향에 따라 연륜폭, 연륜각과 높은 상관관계를 보였다. 유리섬유 보강집성재의 보정항복전단내력은 직경과 보강재에 따라 실측치와 비슷한 경향을 보였으며, 직물형 유리섬유보강집성재의 볼트접합부가 가장 높은 내력성능을 보였다. 볼트직경과 보강재에 따른 유리섬유 보강집성재 볼트접합부의 항복전단내력은 건축구조설계기준의 제안식을 보정한 예측치가 가장 잘 일치하였다.