• Structural Engineering and Mechanics
• /
• v.86 no.6
• /
• pp.751-764
• /
• 2023

In practical engineering such as aerial refueling pipes, the boundary of the fluid-conveying pipe is difficult to be completely immovable. Pipes under movable and immovable boundaries are controlled by different dominant nonlinear factors, where the boundary mobility will affect the nonlinear dynamic characteristics, which should be focused on for adopting different strategies for vibration suppression and control. The nonlinear dynamic instability characteristics of functionally graded fluid-conveying pipes lying on a viscoelastic foundation under movable and immovable boundary conditions are systematically studied for the first time. Nonlinear factors involving nonlinear inertia and nonlinear curvature for pipes with a movable boundary as well as tensile hardening and nonlinear curvature for pipes with an immovable boundary are comprehensively considered during the derivation of the governing equations of the principal parametric resonance. The stability boundary and amplitude-frequency bifurcation diagrams are obtained by employing the two-step perturbation- incremental harmonic balance method (TSP-IHBM). Results show that the movability of the boundary of the pipe has a great influence on the vibration amplitude, bifurcation topology, and the physical meanings of the stability boundary due to different dominant nonlinear factors. This research has guidance significance for nonlinear dynamic design of fluid-conveying pipe with avoiding in the instability regions.

• Structural Engineering and Mechanics
• /
• v.89 no.4
• /
• pp.421-436
• /
• 2024

This research addresses experimentally the relationship between the excitation frequency and both hoop and axial wall stresses in a water storage tank. A low-density polyethylene tank with six different aspect ratios (water level to tank radius) was tested using a shake table. A laminar box with sand represents a soil site to simulate Soil-Structure Interaction (SSI). Sine excitations with eight frequencies that cover the first free vibration frequency of the tank-water system were applied. Additionally, Ricker wavelet excitations of two different dominant frequencies were considered. The maximum stresses are compared with those using a nonlinear elastic spring-mass model. The results reveal that the coincidence between the excitation frequency and the free-vibration frequency of the soil-tank-water system increases the sloshing intensity and the rigid-like body motion of the system, amplifying the stress development considerably. The relationship between the excitation frequency and wall stresses is nonlinear and depends simultaneously on both sloshing and uplift. In most cases, the maximum stresses using the nonlinear elastic spring-mass model agree with those from the experiments.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.15-15
• /
• 1999

In chip plating, several parameters must be taken into consideration. Current density, solution concentration, pH, solution temperature, components volume, chip and media ratio, barrel geometrical shape were most likely found to have an effect to the process yields. The 3 types of barrels utilized in chip plating industry are the conventional rotating barrel. vibrational barrel (vibarrel), and the centrifugal type. Conventional rotating barrel is a close type and is commonly used. The components inside the barrel are circulated by the barrel's rotation at a horizontal axis. Process yield has known to have higher thickness deviation. The vibrational barrel is an open type which offers a wide exposure to electrolyte resulting to a stable thickness deviation. It rotates in a vertical axis coupled with multi-vibration action to facilitate mixed up and easy transportation of components, The centrifugal barrel has its plated work centrifugally compacted against the cathode ring for superior electrical contact with simultaneous rotary motion. This experiment has determined the effect of barrel vibration intensity to the plating thickness distribution. The procedures carried out in the experiment involved the overall plating process., cleaning, rinse, Nickel plating, Tin-Lead plating. Plating time was adjusted to meet the required specification. All other parameters were maintained constant. Two trials were performed to confirm the consistency of the result. The thickness data of the experiment conducted showed that the average mean value obtained from higher vibrational intensity is nearer to the standard mean. The distribution curve shown has a narrower specification limits and it has a reduced variation around the target value, Generally, intensity control in vi-barrel facilitates mixed up and easy transportation of components, However, it is desirable to maintain an optimum vibration intensity to prevent solution intrusion into the chips' internal electrode. A cathodic reaction can occur in the interface of the external and internal electrode. $2HD{\;}+{\;}e{\;}{\rightarrow}20H{\;}+{\;}H_2$ Hydrogen can penetrate into the body and create pressure which can cause cracks. At high intensity, the chip's motion becomes stronger, its contact between each other is delayed and so plating action is being controlled. However, the strong impact created by its collision can damage the external electrode's structure thereby resulting to bad plating condition. 1 lot of chip was divided into two equal partion. Each portion was loaded to the same barrel one after the other. Nickel plating and tin-lead plating was performed in the same station. Portion A maintained the normal barrel vibration intensity and portion B vibration intensity was increased two steps higher. All other parameters, current, solution condition were maintained constant. Generally, plating method find procedures were carried out in a best way to maintained the best plating condition. After plating, samples were taken out from each portion. molded and polished. Plating thickness was investigated for both. To check consistency of results. 2nd trial was done now using different lot of another characteristics.

• Geomechanics and Engineering
• /
• v.21 no.1
• /
• pp.23-33
• /
• 2020

An advancing cutting roof for gob-side entry retaining with no-pillar mining under specific geological conditions is more conducive to the safe and efficient production in a coalmine. This method is being promoted for use in a large number of coalmines because it has many advantages compared to the retaining method with an artificial filling wall as the gateway side filling body. In order to observe the inner structure of the gateway cutting roof and understand its stability mechanism, an equivalent material simulation experiment for a coalmine with complex geological conditions was carried out in this study. The results show that a "self-stabilization bearing structure" equilibrium model was found after the cutting roof caving when the cut line deviation angle was unequal to zero and the cut height was greater than the mining height, and the caving roof rock was hard without damage. The model showed that its stability was mainly controlled by two key blocks. Furthermore, in order to determine the optimal parameters of the cut height and the cut line deviation angle for the cutting roof of the retaining gateway, an in-depth analysis with theoretical mechanics and mine rock mechanics of the model was performed, and the relationship between the roof balance control force and the cut height and cut line deviation angle was solved. It was found that the selection of the values of the cut height and the cut line deviation angle had to conform to a certain principle that it should not only utilize the support force provided by the coal wall and the contact surface of the two key blocks but also prevent the failure of the coal wall and the contact surface.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.1
• /
• pp.1-10
• /
• 2010

The distance distribution in our planetary system has been a controversial matter. Two kinds of important issues on Titius-Bode's relation have been discussed up to now: one is if there is a simple mathematical relation between distances of natural bodies orbiting a central body, and the other is if there is any physical basis for such a relation. We have examined, by applying it to exo-planetary systems, whether Titius-Bode's relation is exclusively applicable to our solar system. We study, with the $X^2$ test, the distribution of period ratios of two planets in multiple planet systems by comparing it with that derived from not only Titius-Bode's relation but also other forms of it. The $X^2$ value between the distribution of the orbital period derived from Titius-Bode's relation and that observed in our Solar system is 12.28 (dof=18) with high probability, i.e., 83.3 %. The value of $X^2$ and probability resulted from Titius-Bode's relation and observed exo-planetary systems are 21.38 (dof=26) and 72.2 %, respectively. Modified forms we adopted seem also to agree with the planetary system as favorably as Titius-Bode's relation does. As a result, one cannot rule out the possibility that the distribution of the ratio of orbiting periods in multiple planet systems is consistent with that derived from Titius-Bode's relation. Having speculated Titius-Bode's relation could be valid in exo-planetary systems, we tentatively conclude it is unlikely that Titius-Bode's relation explains the distance distribution in our planetary system due to chance. Finally, we point out implications of our finding.

• Tunnel and Underground Space
• /
• v.28 no.2
• /
• pp.142-155
• /
• 2018

The ${\bigcirc}{\bigcirc}$ mine has irregularly developed stratum around the ore body. The purpose of this study is to array irregular stratum thickness systematically for effective roof bolting and to implement a supporting system corresponding to it. The number of 81 cases combined with stratum thicknesses was limited to 9 cases by robust design. For each case, the load height which can act as a roof load was determined by the characteristics of stratum and RMR. The load range due to the load height is calculated assuming block shaped and arch shape. The support load of the roof bolt was considered as the average load of the two methods. Numerical analysis results of the support design showed that the cable bolt was more effective for the roof supporting fully grouted than the anchoring type. As a result of the construction, it was possible to control the roof, but all of the roof was gradually sinking downward due to the deformation of the side wall of the mine tunnel.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.235-240
• /
• 2011

A flexible hose attached to a mother ship experiences various motions that depend on the movement of the mother ship and that of underwater vehicle. Although the motion of the hose is a very important factor that determines how a mother ship should be steered in a real situation, it is difficult to experimentally obtain information about the hose motion. Therefore, we study the motion of the hose analytically. The ANCF(absolute nodal coordinate formulation) was used to model the hose, because this formulation can relax the Euler-Bernoulli theory and the Timoshenko beam theory and allow the deformation of the cross section. The mother ship is assumed to be a rigid body with 6 degrees of freedom. The motion of the hose is predominantly affected by the behavior of the mother ship and by the fluid flow.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.10a
• /
• pp.7-7
• /
• 1997

During sintering of very porous green bodies, as obtained by compaction of hard powders - such as tungsten carbide or ceramics - or by injection moulding, important shrinkage occurs. Due to heterogeneous green density field, gravity effects, friction on the support, thermal gradients, etc., this shrinkage is often non-uniform, which' may induce significant shape changes. As the ratio of compact dimension to powder size is very high, the mechanics of continuum is relevant to model such phenomena. Thus numerical techniques, such as the finite element method can be used to simulate the sintering process and predict the final shape of the sintered part. Such type of simulation has much been developed in the last decade firstly for hot isostatic pressing and next for die compaction. Finite element modelling has been recently applied to free sintering. The simulation of sintering should be based on constitutive equations describing the thermo-mechanical behaviour of the material under any state of stress and any temperature which may arise within the sintering body. These equations can be drawn either from experimental data or from micromechanical models. The experiments usually consist in free sintering and sinter-forging tests. Indeed applying more complex loading conditions at high temperature under controlled atmosphere is delicate. Micromechanical models describe the constitutive behaviour of aggregates of spheres from the deformation of two-sphere contact either by viscous flow or grain boundary diffusion. Such models are not able to describe complex microstructure and mechanisms as observed in real materials but they can give some basic information on the formulation of constitutive equations. Practically both experimental and theoretical approaches can be coupled to identify the constitutive equations. Such procedure has been performed for modelling the sintering of compacts obtained by die pressing of a mixture of tungsten carbide and cobalt powders. The constitutive behaviour of this material during sintering has been described by a linear viscous constitutive model, whose functions have been fitted from results of free sintering and sinter-forging experiments. This model has next been introduced in ABAQUS finite element code to simulate the sintering of heterogeneous green compacts of various geometries at constant temperature. Examples of simulations are shown and compared with experiments.

• Journal of Korean Orthopaedic Sports Medicine
• /
• v.7 no.2
• /
• pp.67-74
• /
• 2008

Repetitive overhead throwing exerts significant mechanical stress on the elbow joint. Pitching in baseball, serving in tennis, spiking in volleyball, passing in American football and launching in javelin-throwing can all produce elbow pathology by forceful valgus stress, with medial stretching, lateral compression and posterior impingement. This stress can lead to developmental anatomic changes in the young thrower. Asymptomatic pathology in the shoulder and elbow joint is prevalent and, with overuse, can progress to disabling injury. Joint injury occurs as a result of the body's inability to properly coordinate motion segments during the pitching delivery, leading to further structural damage. The implications of acute and overuse injuries and the possibility of permanent damage should be understood by parents, coaches and the athletes. Proper understanding of the intrinsic and extrinsic risk factors that could lead to elbow injuries is thus required. Measures to prevent elbow injuries should include proper coaching, warm-up, medical expertise and protective gear. Injury prevention and rehabilitation should center on optimizing pitching mechanics, core strength, scapular control, and joint range of motion.

• Physical Therapy Korea
• /
• v.8 no.4
• /
• pp.1-16
• /
• 2001

회전(turning)은 보행 중 방향을 바꾸는 운동 기술(motor skill)이고, 회전 전략(turning strategy)은 회전을 완수하는데 사용되는 일반적 행동 전형(generalized movement pattern)이다. 회전에 대한 보행속도의 영향은 분명하지 않다. 이 연구의 목적은 보행속도의 돌기 전략에 대한 영향을 분석하고 보행속도의 하지 내외 회전(internal and external rotation)에 대한 영향을 분석하는 것이다. 건강한 젊은 성인 15명이 이 연구에 자발적으로 참여하였다. 맥리플렉스 측정 장치(MacReflex measurement system)가 동작 분석(motion analysis)을 위해 사용되었다. 각각의 자원자들은 보행 중 90도 왼쪽으로 회전을 10회씩 완수하였다. 각각의 시도마다 보행속도를 다르게 하기 위해서 세 가지의 다른 요구들(slow, regular, fast)이 임의적으로 주어졌고 각각의 실제 보행속도가 자원자의 무게중심 변화에 따라 구해졌고 요구별 평균이 구해졌다. 회전 안쪽 발의 스핀(in side foot spin)은 보행속도가 증가함에 따라 증가했지만, 회전 바깥쪽 발의 스핀(out side foot spin)은 보행속도와 상관이 없었다. 하지의 내외 회전은 보행속도와는 상관이 없었지만, 같은쪽 발의 스핀과는 역관계가 있었다. 회전은 발 스핀이 있는 돌기와 발 스핀이 없는 돌기로 구분되는 것이 합당한 듯 하다. 제한된 시간과 공간 내에서 스핀은 보행속도가 빨라질수록 몸의 전방 운동량(forward momentum)에서 몸의 전방 운동량(forward momentum)으로의 전환이 스핀이 없는 회전 시보다 효율적이다. 고관절의 내외 회전 근육들은 회전전략에 상관없이 회전되는 동안 몸의 역학(body mechanics)을 조절하는데 중요한 역할을 맡고 있는 것으로 보인다. 앞으로 회전 시 몸의 생체 역학적 그리고 신경 근육적 기전들(biomechanical and neuromuscular mechanisms)을 밝히는 연구들이 필요하다.