• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.1
• /
• pp.19-31
• /
• 2022

Damages by jellyfish are occurring frequently around the world. Among them, accidents caused by jellyfish stings are serious enough to cause death. So we designed a jellyfish blocking net and analyzed its stability to prevent sting caused by jellyfish entering the beach. To this end, the dynamic behavior of the jellyfish blocking net according to the current speed (0.25-1.0 m/s) and the net type (50, 100 and 150 mm) on the upper part of the blocking net was modeled using the mass spring model. As a result of simulations for the model, the horizontal tension (horizontal component of the mooring tension) of the mooring line increased with the decrease in the mesh size on the upper part of the blocking net at all current speeds, but exceeded the holding force at high tides faster than 0.5 m/s and exceeded the holding force at all current speeds at low tide. Therefore, the jellyfish blocking nets showed poor stability overall. The depth of the float line had a little difference according to the upper mesh size and increased lineary proportional to the current speed. However, the float line sank too much to block the incoming jellyfish. These analysis results helped us find ways to improve the stability of the jellyfish blocking net, such as adjusting the length of the mooring line and improving the holding power. Therefore, it is expected that this technology will be applied us various underwater structures to discover the weaknesses of the structures and contribute to increasing the stability in the future.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.148-149
• /
• 2003

The parasitic effects due to the current blocking layer limit the bandwidth of the semiconductor laser diode. Thus, the parasitic response of various blocking layers was analyzed. The inin type was the best choice for the leakage current reduction and the bandwidth expansion.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.257-260
• /
• 2002

This study is intended is to analyze the blocking performance with variation of the gap of bar and kinds of metal lath for construction joint when placing concrete. According to the results, passing ratio of concrete increases with increase of vibrating time. In the case of W/C 50%, when blocking concrete with bar of D10 and D20 which the gap of bar is below 200mm, or metal lath, passing ratio of concrete is below 10%, so blocking performance is favorable. In the case of W/B 30%, while concrete does not flow out without vibration at slump 21mm, concrete flows out at some degree before vibration at slump flow 65mm and then, as 5 seconds passes after first vibration, final passing ratio shows about 85~90%. When blocking concrete by bar D10 of the gap 20mm, bar D20 of the gap 10mm and metal lath, it is thought that concrete can be blocked effectively because final passing ratio is below 10%.

• Journal of Pharmaceutical Investigation
• /
• v.15 no.1
• /
• pp.22-31
• /
• 1985

The influence of some sympathetic blocking agents on pressor actions of norepinephrine and angiotensin was investigated in rabbits. 1. Phentolamine, sympathetic ${\alpha}-blocking$ agent, blocked the pressor action of norepinephrine, but did not affect the pressor action of angiotensin 2. Chlorisondamine, autonomic ganglionic blocking agent, potentiated the both actions of norepinephrine and angiotensin. 3. Guanethidine, bethanidine and debrisoquine, sympathetic neuronal blocking agents, potentiated the action of norepinephrine, while diminished that of angiotensin. 4. Reserpine, norepinephrine depleting agent, increased the pressor response of norepinephrine, but did not influence the pressor action of angiotensin.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.22 no.4
• /
• pp.173-182
• /
• 1997

In this paper, an efficient dynamic channel assignment scheme is suggested, which consists of two types of channel allocation strategies : ordinary channel allocation strategy and channel reallocation strategy. An analysis on the handoff probabilities of handoff and new calls is also performed, and using the analyzed handoff probability, the presented scheme is compared with other existing schemes in terms of three types of blocking probabilities- new call blocking probability, handoff call blocking probability, and network blocking probability (incomplete service probability). Simulation results show that the presented scheme significantly reduces those blocking probabilities over the existing schemes. Furthermore, the scheme has much smaller number of reallocation than other schemes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.3
• /
• pp.201-207
• /
• 2002

In this paper, we haute proposed a novel trench electrode Base Resistance Thyristor(BRT) and trench electrode BRT with a intrinsic region. New power BRTs have shown superior electrical characteristics including the snab-back effect and the forward blocking voltage more than the conventional BRT. Especially, the trench electrode BRT with the intrinsic region has obtained high blocking voltage of 1600V. The blocking voltage of conventional BRT is about 400V at the same size. Because the breakdown mechanism of the BRT is the avalanch breakdown by impact ionization, the trench electrode BRT with intrinsic region has suppressed impact ionization, effectively. If we use this principle, we can develop a super high voltage power device and it applies to another power device including IGBT, EST and etc.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.63-64
• /
• 2006

Here we present detailed simulation results of trench field stop IGBTs. Besides the reduced on-state voltage drop there is also an Increase of forward blocking voltage. A trench gate IGBT has low on-state voltage drop mainly due to the removal of the JFET region and a field stop IGBT has high forward blocking voltages due to the trapezoidal field distribution under blocking condition. We have simulated the static characteristics of TIGBT with field stop technology by 2D simulator(MEDICI). The simulated result of forward blocking voltage and on-state voltage drop is about 1,408V and 1.3V respectively at $110{\mu}m$ N-drift thickness.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1148-1151
• /
• 2005

Photovoltaic effects in organic solar cell were studied in a cell configuration of ITO/PEDOT:PSS/CuPc(20 nm)/$C_{60}$(40 nm)/BCP/Al(150 nm) at room temperature. Here, the BCP layer works as an exciton blocking layer. The exciton blocking layer must transport electrons from the acceptor layer to the metal cathode with minimal increase in the total cell series resistance and should absorb damage during cathode deposition. Therefore, a proper thickness of the exciton blocking layer is required for an optimized photovoltaic cell. Several thicknesses of BCP were made between $C_{60}$ and Al. And we obtained characteristic parameters such as short-circuit current, open-circuit voltage, and power conversion efficiency of the device under the illumination of AM 1.5.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.136-142
• /
• 2005

The function of main starting valve for marine engine is to supply cylinder with the air to start marine engine. But, if the spindle, one of the main starting valve components, doesn't rotate accurately at the designated air pressure, the marine engine may have some trouble in starting. So, to resolve the problem due to spindle .elation in the main starting valve, the blocking device (blocking plate, limit switch, etc.) is installed in the upper part of spindle to constrain the rotation. So, in this paper we introduced the rotation constraining ability of blocking plate prevent the spindle from mis-working in the main starting value of the marine engine.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.273-274
• /
• 2005

Photovoltaic effects in organic solar cell were studied in a cell configuration of ITO/PEDOT:PSS/CuPc(20nm)/$C_{60}$(40nm)/BCP/Al(150nm) at room temperature. Here, the BCP layer works as an exciton blocking layer. The exciton blocking layer must transport electrons from the acceptor layer to the metal cathode with minimal increase in the total cell series resistance and should absorb damage during cathode deposition. Therefore, a proper thickness of the exciton blocking layer is required for an optimized photovoltaic cell. Several thicknesses of BCP were made between $C_{60}$ and Al. And we obtained characteristic parameters such as short-circuit current, open-circuit voltage, and power conversion efficiency of the device under the illumination of AM 1.5.