• 대한조선학회논문집
• /
• 제61권5호
• /
• pp.389-399
• /
• 2024

Currently, shipyards are using ship block supports to hold various pre-erection (PE) blocks during ship construction work. The height adjustment method of the ship block support is performed by workers hammering and driving the wedge part, which requires repetitive high-load work. Accordingly, there are concerns about musculoskeletal diseases and safety accidents. To prevent safety accidents and improve work efficiency, this study developed a block support height adjustment device using a hydraulic cylinder. It was designed considering the ease of movement of the block support height adjustment device and the ease of adjusting the height of the block support by workers within the shipyard. Numerical analysis was conducted to confirm the critical points of the structural members of the designed block support height adjustment device and to verify the safety of the stress-based structure. As a result of the analysis, it was confirmed that the stress occurring at the critical point of the structural member was lower than the design allowable stress, making it structurally safe. Afterwards, the block support height adjustment device was redesigned for lightweight, and after verification of structural safety through numerical analysis, a prototype was manufactured and performance evaluation was conducted.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• 대한기계학회논문집B
• /
• 제32권10호
• /
• pp.776-783
• /
• 2008

The object of this paper is to study on the thermal performance of a micro channel water block for computer CPU cooling. The effects of liquid flow rate, micro channel width and height on the thermal performances of water block are investigated experimentally. The water block was fabricated Al and machined with a micro milling. The water block consisted of rectangular micro channels 0.5 to 0.9 mm width and 1.5 to 4.5 mm height. The experiments were conducted using deionized water, over a liquid flow rate ranging from 0.2 to 2.0 kg/min. The base temperature and thermal resistance decrease with increasing of liquid flow rate. The increase of a channel height is more effective on the thermal resistance than the decrease of a channel width. At the flow rate of 0.7 kg/min, input power of 100 W, the base temperature and thermal resistance of sample 6 is $33^{\circ}C$ and $0.13\;^{\circ}C/W$ respectively.

• Earthquakes and Structures
• /
• 제24권3호
• /
• pp.205-215
• /
• 2023

Currently, many studies are underway at home and abroad on the seismic performance evaluation and dry construction method of the masonry structure. In this study, a dry stack masonry wall system without mortar using concrete blocks is proposed, and investigate the seismic performance of dry filling wall frames through experimental studies. First, two types of standard blocks and key blocks were designed to assemble dry walls of concrete blocks. And then, three types of experiments were manufactured, including pure frame, 1/2 height filling wall frame, and full height filling wall frame, and cyclic load experiments in horizontal direction were performed to analyze crack patterns, load displacement history, rebar deformation yield, effective stiffness change, displacement ductility, and energy dissipation capacity. According to the experimental results, the full height filling wall frame had the largest horizontal resistance against the earthquake load and showed a high energy dissipation capacity. However, the 1/2 height filling wall frame requires attention because the filling wall constrains the effective span of the column, limiting the horizontal displacement of the frame. In addition, the concrete block was firmly assembled in the vertical direction of the wall as the horizontal movement between the concrete blocks was allowed within installation margin, and there was no dropping of the assembled concrete block.

• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.294-302
• /
• 1998

Ignition characteristics of a vertical solid fuel plate with block have been investigated experimentally. For low radiant heat flux, ignition does not occur in a vertical solid fuel plate without block. In the case with the block on a vertical fuel plate, however, ignition can occur by increasing the residence time and the time to absorb the incident radiation flux by fuel vapor in gas phase. The ignition occurs below block and the point varies according to the block location and the block height. As the block height increases, the block locates at higher position, and the hot wall temperature increases, the ignition delay time decreases. Also as the initial temperature of fuel plate rises, the ignition delay time of the solid fuel plate decreases. The temperature distribution of solid fuel plate with block is nearly proportional to the radiant heat flux distribution. Therefore, the effect temperature by natural convection heat transfer is of the same order as that of inhibition of temperature increase by pyrolysis.

• Ocean Systems Engineering
• /
• 제8권1호
• /
• pp.57-77
• /
• 2018

The present paper deals with the finite element analysis of water tanks with rigid baffle. Fluid is discretized by two dimensional eight-node isoparametric elements and the governing equation is simulated by pressure based formulation to reduce the degrees of freedom in the domain. Both free vibration and force vibration analysis are carried out for different sizes and positions of block at tank bottom. The fundamental frequency depends on block height and it reduces with the increase of block height. The variation of hydrodynamic pressure on tank walls not only depends of the exciting frequency but also on the size and position of rigid block at tank bottom. The hydrodynamic pressure has higher value when the exciting frequency is equal and lower than the fundamental frequency of the water in the tank. Similarly, the hydrodynamic pressure increases with the increase of width of the block for all exciting frequencies when the block is at the centre of tank. The left and right walls of tank have experienced different hydrodynamic pressure when the block is placed at off-centre. However, the increase in hydrodynamic pressure on nearest tank wall becomes insignificant after a certain value of the distance between the wall and the rigid block.

• 태양에너지
• /
• 제9권1호
• /
• pp.62-69
• /
• 1989

This analysis is to investigate the influence of inflow angle when cooling air flows into PC (Printed Circuit) board channels. Flow between PC board channels with heat generating blocks is assumed laminar, incompressible, two-dimensional. Geometric parameters (block spacing (S), block height (H), block width (W) and channel height (L)) are held fixed. Inflow angle variations are $-10^{\circ},\;0^{\circ},\;10^{\circ}$, where uniform heat flux per unit axial length Q (W/m) from heated block surfaces is generated. The governing equations for velocity and temperature are solved by SIMPLE (Semi-Implicit Method Pressure for Linked Equation) algorithm. Nusselt number on each block surfaces is analyzed after a numerical calculation result. The result shows that the assumption on parallel inflow (inflow angle to channel, $0^{\circ}$) to PC board channels can be used without large error even when inflow' angle is varied.

• 설비공학논문집
• /
• 제7권3호
• /
• pp.461-472
• /
• 1995

The interaction of laminar mixed convection and surface radiation in a two-dimensional channel with an array of rectangular blocks is analyzed numerically. Three blocks are maintained at high temperature and the other bottom and top horizontal walls are insulated. Discrete ordinate method(DOM) is introduced to analyze the radiative heat transfer. The effects of the variations of Reynolds number and channel specifications on the heat transfer characteristics are investigated. The average Nusselt numbers along the block surfaces are correlated and presented in terms of Reynolds number and dimensionless geometric parameters such as the block spacing, height and channel spacing. For the conditions considered in this study, average Nusselt numbers along the block surfaces are strongly influenced by the channel spacing and Reynolds number but weakly influenced by the block spacing and block height.

• 한국생활과학회지
• /
• 제10권4호
• /
• pp.379-390
• /
• 2001

The purpose of this study is to investigate the fitness according to drafting method of the block patterns for women in Korea. The major findings of this study are as follows: 1. According to comparative analysis of required measurements, two measurements of back length and bust girth are used in Proportional Drafting Method (Munhwa). In case of Compromise Drafting Methods are used across chest, across back, bust length, bust width, full length in front, across shoulder and shoulder length in addition to back length and bust girth. The type of Armstrong as a Short Measure Drafting Method uses 10 measurements for the drafting the bodice. 2. While Esmod block pattern arid Armstrong's block pattern are the lightest in full width and other widths. Rasara block pattern is the most ample. In Lee, Myung-hee's block pattern and Lee, Hyung-sook's block pattern, amounts of drooping are decided $3{\sim}4cm$, but drooping amounts of other block patterns are decided corresponding to real measurements. While cap height in Esmod and Armstrong's sleeve patterns are directly measured Armhole length of the block pattern, cap height of other sleeve patterns are used armhole depth and cap height length as well as armhole length. 3. When analyzing to indirect measurements, Esmod block pattern shows the least different between full length of block pattern and that of body form. Munhwa block pattern and Kim, Hyosook's block pattern are mostly same to body form back length. However all of the block patterns are sheller than body form length. In case of Suh, Wansuk's block pattern, across back and across chest are same size, but other block patterns show difference between across back and across chest. Most block patterns' neck width in front and bach bodice are almost same. Front neck width is generally bigger than back neck width in some cases.

• 패션비즈니스
• /
• 제10권1호
• /
• pp.41-57
• /
• 2006

The purpose of this study were to provide dress forms and men's jacket blocks based on the analysis of their somatotype. As the result of the previous research, based on 1290 males of 20 to 54 year-old, the shapes of adult male were 20 and each body shape was classified by size factor, height and chest girth and master size was selected considering appearance frequency. Somatotype YS(master size: height 170cm, chest girth 91cm) and HD1(master size: height 170cm, chest girth 94cm) were selected to develop dress forms and men's jacket block in the study. The procedure and results were follows; 1. The dress forms of somatotype YS and HD1 were provide base on means of 61 body measurements and cross sections of shoulder, chest, waist, hip of subjects belong to each somatotype. 2. New men's jacket blocks of somatotype YS and HD1 were developed based on the body surface extracted by draping and the result of comparative investigation on the conventional jacket patterns by wearing test. Also the drafting methods of new men's jacket blocks were provided. 3. Wearing test by the sensory evaluation showed that the developed jacket blocks were estimated more highly than existing patterns.