• Journal of the Korean Institute of Gas
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2010

In this study, we experimentally investigated a compression ignition engine operated with Bio-diesel blended LPG fuel. In particular, the performance, emissions characteristics (including total hydrocarbon, carbon monoxide, nitrogen oxides, and carbon dioxides emissions), and combustion stability of a CI engine fueled with Bio-diesel blended LPG fuel were examined at 1500 rpm. The percentage of Bio-diesel in the fuel blend ranged from 20-60%. The results showed that stable engine operation was possible for a wide range of engine loads up to 40% Bio-diesel by mass. When the Bio-diesel content was increased, leading to a decrease in the lower heating value of the blended fuel, the cetane value increased, resulting in a advanced start of heat release. Exhaust emission measurements showed that THC and CO emissions were increased when using the blended fuel at low engine speeds due to partial burn from over-mixing. NOx emission was emitted less at lower loads and more at higher loads.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.380-388
• /
• 2017

Wood pyrolysis oil(WPO) has been regarded as an alternative fuel for diesel engines. However, WPO is not feasible for use directly in diesel engines due to its poor fuel quality such as low energy density, high acidity, high viscosity and low cetane number. The most widely used approach to improve WPO fuel quality is to blend WPO with other hydrocarbon fuels that have a higher cetane number. However, WPO and fossil fuels are not usually blended because of their different polarity. Also, clogging and polymerization problems in the fuel supply system can occur when the engine is operated with WPO. Polymerization can be prevented by diluting WPO with other alcohol fuels. However, WPO-alcohol blended fuel does not produce self-ignition. Therefore, additional cetane enhancement to the blended fuel is required to enhance auto-ignitability. In this study, WPO was blended with n-butanol and two cetane enhancements(PEG 400 and 2-EHN) for application to a diesel generator. Experimental results showed that the WPO-butanol blended fuel achieved a very stable engine operation under maximum WPO content of 20 wt%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.101-110
• /
• 2002

In this paper, the effects of oxygen component in blended fuel on the exhaust emissions have been investigated far direct injection diesel engine. It was tested to estimate change of engine performance and exhaust emission characteristics for th? commercial diesel fuel and oxygenated blended fuels which have three kinds of fuels and various mixed rates. And, it was tried to analyze not only total hydrocarbon but individual hydrocarbons(C$_1$∼ C$\_$6/) in exhaust gases using gas chromatography to seek the reason far remarkable reduction of smoke emission on various oxygenated fuels. This study carried out by comparing the chromatogram with diesel fuel and diesel fuel blended DGM(diethylene glycol dimethyl ether), MTBE(methyl tart-butyl ether) and EGBE(ethylene glycol mono-n-butyl ether). The results of this study show that individual hydrocarbons as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with commercial diesel fuel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.75-82
• /
• 2003

DME is a good alternative fuel to reduce the smoke remarkably when used in a diesel engine, while problems concerned with low lubricity and high compressibility exist. In the present study, single cylinder DI diesel engine was operated with neat DME and DME blended fuels which are DME-diesel blended fuel and DME-propane blended fuel. The results showed that the power of the neat DME and DME blended fuels was the same as that of pure diesel oil, and the specific energy consumption slightly increased. In addition, smoke emission was considerably reduced with the increase of DME content up to zero level, but NOx emission was slightly increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.10
• /
• pp.3381-3386
• /
• 1996

The engine performance and combustion characteristics of methanol blended fuel in spark ignition engine were discussed on the basis of experimental investigation. The effects of methanol blending fuel on combustion in cylinder were investigated under various conditions of engine cycle and blending ratio. The results showed that the engine performance was influenced by the methanol blending ratio and the variations of operating conditions of test engine. The increase of fuel temperature brought on the improvement of combustion characteristics such as cylinder pressure, the rate of pressure rise and heat release in an engine. The burning rate of fuel-air mixture, the exhaust emissions and the other characteristics of performance were discussed also.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.91-97
• /
• 2010

This paper described the effects of DME blended fuel on the engine combustion and emission characteristics of four cylinder CRDI diesel engine. Biodiesel was added into the DME fuel in order to improve the low kinematic viscosity of DME fuel. In this work, the experiment was performed under th various injection timings and injection strategy at constant engine speed and engine load. To maintain the fuel pressure and temperature, pressure and temperature controllers were installed to the DME fuel system. The results show that ignition delay was shortened and combustion duration was extended when DME blended fuel is supplied. Despite of slightly higher NOx emission with DME blended fuel at equal conditions in comparison with those of diesel fuel, the engine showed lower HC and CO emission characteristics.

• Journal of Power System Engineering
• /
• v.12 no.1
• /
• pp.5-12
• /
• 2008

We measured emission characteristics of CRDI diesel engine equipped with a commercial CPF. Experimental parameters adopted a neat diesel fuel, a blend of diesel fuel with 20% biodiesel, a blend of diesel fuel with 15% biodiesel and 5% ethanol. The experiments were carried out to measure the emission and engine performance according to ESC 13-mode cycles. The maximum torque with biodiesel blend fuel is slightly lower than that of neat diesel fuel in the entire the 13-mode cycles, and 5% ethanol and 15% biodiesel blend fuel is slightly higher than that of neat diesel fuel. THC and CO emissions of the biofuel blended diesel fuel were slightly increased and decreased, and mean conversion efficiencies of THC and CO on the commercial CPF were achieved about 70$\sim$87% in the ESC 13-mode. From the measurement by the Scanning Mobility Particle Sizer(SMPS), the total number and mass of nano-sized particles by a commercial CPF were decreased about 97.8% and 96.8 % in the range of the nano-size from 10.6 to 385nm, respectively.

• Journal of ILASS-Korea
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2012

This study described the effect of the multiple injections and diesel-ethanol on the NVH, combustion and emission characteristics of 4 cylinder common rail diesel engine. In order to investigate the influence of diesel-ethanol blended fuel in a light-duty common rail diesel engine, the injection strategy was varied with pilot injection, double pilot injections, and one main injection at various operating conditions. The results showed that diesel-ethanol blended fuel had longer ignition delay than that of the ultra low diesel fuel(ULSD). Also, in the case of multiple injections, the combustion pressure is increased smoothly near the TDC and the NVH are decreased. In the emission characteristics, diesel-ethanol blended fuel produced lower indicated specific nitrogen oxides(IS-NOX) and indicated specific Soot(IS-soot) emissions, however, indicated specific unburned hydrocarbon(IS-HC) and indicated specific carbon monoxide(IS-CO) emissions are slightly increased.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.235-241
• /
• 2004

This experiment was undertaken to investigate the atomization characteristics of the high viscosity biodiesel blended fuel and ultrasonic energy irradiation one. Test fuels were conventional diesel fuel and biodiesel one. We compared to the characteristics of viscosity and surface tension, SMD between high viscosity biodiesel blended fuel and ultrasonic energy irradiation one. Sauter mean diameter was measured under the variation of the spray distance. Viscosity and surface tension were measured under the variation of the time trace. To measure the droplet size, we used the Malvern system 2600c. Droplet size distribution was analyzed from the result data of Malvern system. Through this experiment, we found that the condition of the ultrasonic energy irradiation situation had smaller Sauter mean diameter of droplet, viscosity and surface tension than those of the conventional situation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.7
• /
• pp.722-728
• /
• 2005

In this paper, the effects of ethanol blended gasoline on emissions and their catalytic conversion efficiency characteristics were investigated in a multiple-point EFI gasoline engine, The results show that with the increase of ethanol concentration in the blended fuels, THC emissions were drastically reduced by up to thirty percent, And brake specific fuel consumption was increased, but brake specific energy consumption could be improved. However, unburned ethanol and acetaldehyde emissions increased. Pt/Rh based three-way catalysts were effective to reduce acetaldehyde emissions, but had low catalytic conversion efficiency for unburned ethanol. The effect of ethanol on CO and NOx emissions and their catalytic conversion efficiency had close relation to the engine's speed, load and air/fuel ratio. Furthermore fuels blended with thirty percent ethanol by volume could dramatically reduced THC CO and NOx emissions at idle speed.