• Resources Recycling
• /
• v.18 no.2
• /
• pp.51-55
• /
• 2009

Sawdust and sewage sludge and PE gasification by high temperature steam of Brown gas have been performed in this study. Steam/carbon ratio has been changed from 1 to 5 and the effect of steam/carbon ratio on the produced gas concentrations, gasification rate and tar generation has been determined. Also, the temperature distribution in the gasification reactor has been studied. Highest combustible content in the produced gas is around 70vol% and $H_2$ shows highest content among the combustible compounds. However, the heating value of the produced gas and tar content have been reduced with increasing steam/carbon ratio.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.804-815
• /
• 2019

Due to the depletion and environmental problems of fossil fuel, biomass has arisen as an alternative energy source. Biomass is a renewable and carbon-neutral source. However, it is moister and has lower energy density. Therefore, biomass needs thermal chemical conversion processes like gasification, and it does not only produce a flammable gas, called 'syngas', which consists of CO, H2, and CH4, but also some unwanted byproducts such as tars and some particulates. These contaminants are condensed and foul in pipelines, combustion chamber and turbine, causing a deterioration in efficiency. Thus this work attempted to find a method to remove tars and particles from syngas with a filter which adopts a pre-coating technology for preventing blockage of the filter medium. Hydrated limestone powder and activated carbon(wood char) powder were used as the pre-coat materials. The removal efficiency of the tars was 86 % and 80 % with activated carbon(wood char) coating and hydrated limestone coating, respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.1
• /
• pp.8-14
• /
• 2015

In this study, the model biomass was used for hydrogen production by supercritical water gasification (SCWG). Model biomasses were glycerol, glycine, lignin and cellulose. The feed concentration was set to 1 wt%. Experiments were conducted in a reactor at $440^{\circ}C$ and above 26.3 MPa for 30 min. The effects of catalysts such as alkali metal salt ($K_2CO_3$ and $Na_2CO_3$) and transition metal salts ($Ni(NO_3)_2$, $Fe(NO_3)_3$ and $Mn(NO_3)_2$) on the gasification were systematically investigated. No tar or coke was observed in all experiments. The results showed that the gasification efficiency increased with various catalysts. For the cellulose and glycerol, all catalysts were effective for the promoted $H_2$ production compared with no catalyst. The significant decrease of $H_2$ production compared with no catalyst was observed with $Na_2CO_3$ and $Fe(NO_3)_3$ for glycine and lignin. respectively. The highest H2 production, 1.24 mmol was obtained for glycerol-SCWG with $Mn(NO_3)_2$. Conclusively, the addition of $Mn(NO_3)_2$ enhanced all model biomass gasification efficiency and increased the hydrogen production promoting the supercritical water reaction.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.214-225
• /
• 2016

Gasification is one of the important contribution to resource recycling by conversion of biomass to a variety of energy sources such as alcohol, SNG etc., and to global warming prevention by reduction of green house gases such as $CO_2$. The aim of this study is to draw the optimal operation condition of dual fluidized-bed gasifier with biomass fuel, to verify SNG production efficiency and to establish the basis for the domestic commercialization of dual fluidized bed gasification. As a result, dual fluidized-bed gasifier has the optimal conditions at $826^{\circ}C$ with steam input 1,334 g/hr, air input 5.56 L/min. The carbon conversion is 81% and SNG production efficiency was $CH_4$ 92%.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.874-882
• /
• 2019

In this study, the gasification characteristics of four types of unused woody biomass and one waste wood in a lab-scale bubbling fluidized bed gasifier (Diameter: 0.11 m, Height: 0.42 m) were investigated. Effect of equivalence ratio (ER) of 0.15-0.3 and gas velocity of $2.5-5U_0/U_{mf}$ are determined at the constant temperature of $800^{\circ}C$ and fuel feeding rate of 1 kg/h. The silica sand particle having an average particle size of $287{\mu}m$ and olivine with an average particle size of $500{\mu}m$ were used as the bed material, respectively. The average product gas composition of samples is as follows; $H_2$ 3-4 vol.%, CO 15-16 vol.%, $CH_4$ 4 vol.% and $CO_2$ 18-19 vol.% with a lower heating value (LHV) of $1193-1301kcal/Nm^3$ and higher heating value (HHV) of $1262-1377kcal/Nm^3$. In addition, it was found that olivine reduced most of C2 components and increased $H_2$ content compared to silica sand, resulting in cracking reaction of tar. The non-condensable tar decreases by 72% ($1.24{\rightarrow}0.35g/Nm^3$) and the condensable tar decreases by 27% ($4.4{\rightarrow}3.2g/Nm^3$).

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.6
• /
• pp.17-22
• /
• 2011

Biomass gasification provides synthesis gas or syngas that can be used for internal combustion engines as fuel or chemical synthesis as feedstock. Among different types of gasifiers, downdraft gasifier can produce relatively clean syngas with lower tar contents. In this study, a downdraft gasifier was fabricated with 150 mm of hearth diameter to gasify woodchip that is commercially available in this country. After drying woodchip to about 20 %, gasification experiments were conducted measuring temperature, pressure, air and gas flow rates. The volumetric concentrations of CO, $H_2$, $CO_2$, $CH_4$ were 10.7~14.5, 16.5~21.4, 12.5~16.6, and 2.3~2.9, respectively. They were overall within the ranges of the results that the previous studies showed. However, CO concentration was relatively lower and H2 was slightly higher than those from other studies. It seemed that water gas shift reaction was occurred due to the moisture in the fuel woodchip. Additional drying process coupled with syngas cooling would be required to improve the overall efficiency and syngas quality.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.354-361
• /
• 2019

Renewable energy from biomass and biodegradable wastes can significantly supplement the global energy demand if properly harnessed. Pyrolysis is the most profound modern technique that has proved effective and efficient in the energy conversion of biomass to yield various products like bio-oil, biochar, and syngas. This study focuses on optimization of slow pyrolysis of banana peels waste to yield banana peels vinegar, tar and biochar as bio-infrastructure products. Response surface methodology using central composite design was used to determine the optimum conditions for the banana wastes using a batch reactor pyrolysis system. Three factors namely heating temperature ($350-550^{\circ}C$), sample mass (200-800 g) and residence time (45-90 min) were varied with a total of 20 individual experiments. The optimal conditions for wood vinegar yield (48.01%) were $362.6^{\circ}C$, 989.9 g and 104.2 min for peels and biochar yield (30.10%) were $585.9^{\circ}C$, 989.9 g and 104.2 min. The slow pyrolysis showed significant energy conversion efficiencies of about 90% at p-value ${\leq}0.05$. These research findings are of primary importance to Uganda considering the abundant banana wastes amounting to 17.5 million tonnes generated annually, thus using them as pyrolysis feedstock can boost the country's energy status.

• Journal of Energy Engineering
• /
• v.16 no.2
• /
• pp.83-92
• /
• 2007

In view of stringent environment regulations to control the emission of green house gases and also depleting fossil fuel reserves, it is high quality desirable to develop alternative technologies to produce high quality fuels. To this end Biomass to Liquid (BTL) technology has received much attention in recent years. BTL process generally consists of gasification of biomass to produce bio-syngas, cleaning and control of $H_{2}/CO$ mole ratio of bio-syngas and Fischer-Tropsch synthesis & upgrading systems. Choren, Germany has first developed the commercial BTL process using unique gasification system i.e., Carbo-V. A new technology to remove tars and BTX has been developed by ECN in Netherlands employing a gasification system combined with OLGA technology. Several other countries including USA and Japan are showing great interest in BTL technology. Thus in view of our national energy security and also the environmental regulations, it is essential to develop alternative technologies like BTL in order to meet the increasing demand of energy though our insufficient biomass resources. In this paper we present an overview and development status of BTL-diesel technology.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.256-259
• /
• 2008

The gasification of biomass, sawdust, was carried out in order to investigate gasification characteristics. The experiment was performed using a down-draft fixed bed gasifier to surpass tar components generation in the gasification process. In the experiments, we investigated synthetic gas composition by varying reaction temperature, steam/carbon ratio, and excess ratio (ER), respectively. Higher reaction temperature, $700^{\circ}C$ to $900^{\circ}C$, could obtain higher $H_2$ yield. However, we could not obtain any meaning data by varying S/C ratio. Using $O_2$-LNG burner in the top of the gasifier may surpass water-gas shift reaction by increasing $CO_2$ concentration from the LNG-$O_2$ combustion reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.9
• /
• pp.499-504
• /
• 2015

The composite anodes of expanded graphite (EG) and multiwall carbon nanotube (MWCNT) for microbial fuel cells were fabricated by using coal tar pitch (CTP) binder containing nickel (Ni), and the effect of the anodes with the binders on the performance of the MFCs were examined in a batch reactor. During the start-up of the MFCs, quick increase in voltage was observed after a short lag phase time, indicating that the CTP binder is biocompatible. The biomass attatched on the anode surface was more at higher Ni content in the binder, as well as at smaller amount of CTP binder for the fabrication of the anode. The internal resistance of the MFC was smaller for the anode with more biomass. Based on the results, the ideal combination of CTP and Ni for the CTP binder for anode was 2 g and 0.2 g, respectively. The maximum power density was $731.8mW/m^2$, which was higher 23.7% than the anode with Nafion binder as control. The CTP binder containing Ni for the fabrication of anode is a good alternative in terms of performance and economics of MFCs.