• Bulletin of the Korean Chemical Society
• /
• 제35권3호
• /
• pp.811-814
• /
• 2014

Bio-oil instability, or aging, is a significant problem for the long-term storage of fast pyrolysis oils. We investigated bio-oil aging at the molecular level using Fourier-transform ion cyclotron resonance mass spectrometry. Petroleomic analysis suggests that bio-oil aging is resulted from the oligomerization of phenolic lignin products whereas 'sugaric' cellulose/hemicellulose products have negligible effect.

• Journal of the Korean Wood Science and Technology
• /
• 제47권3호
• /
• pp.344-359
• /
• 2019

Effects of various types of zeolite on the catalytic performance of hydrodeoxygenation (HDO) of bio-oil obtained from waste larch wood pyrolysis were investigated herein. Bifunctional catalysts were prepared via wet impregnation. The catalysts were characterized through XRD, BET, and SEM. Experimental results demonstrated that HDO enhanced the fuel properties of waste wood bio-oil, such as higher heating values (HHV) (20.4-28.3 MJ/kg) than bio-oil (13.7 MJ/kg). Water content (from 19.3 in bio-oil to 3.1-16.6 wt% in heavy oils), the total acid number (from 150 in bio-oil to 28-77 mg KOH/g oil in heavy oils), and viscosity (from 103 in bio-oil to $40-69mm^2/s$ in heavy oils) also improved post HDO. In our experiments, depending on the zeolite support, NiFe/HBeta exhibited a high Si/Al ratio of 38 with a high specific surface area ($545.1m^2/g$), and, based on the yield of heavy oil (18.3-18.9 wt%) and HHV (22.4-25.2 MJ/kg), its performance was not significantly affected by temperature and solvent concentration variations. In contrast, NiFe/zeolite Y, which had a low Si/Al ratio of 5.2, exhibited the highest improved quality for heavy oil at high temperature, with an HHV of 28.3 MJ/kg at $350^{\circ}C$ with 25 wt% of solvent.

• 한국산업융합학회 논문집
• /
• 제4권1호
• /
• pp.11-19
• /
• 2001

This study was carried out to investigate the feasibility of the used frying oil as a bin-oil which was one of the alternative fuel for diesel engine. From tests of engine performance, it was shown that the bio-oil and blends and the sufficient potential as alternative fuels of diesel engine except NOx and Smoke emission.

• Environmental Engineering Research
• /
• 제25권1호
• /
• pp.18-28
• /
• 2020

In this paper the authors provide comparative evaluation of current research that used liquefaction and pyrolysis method for bio-oil production from various types of biomass. This paper review the resources of biomass, composition of biomass, properties of bio-oil from various biomass and also the utilizations of bio-oil in industry. The primary objective of this review article is to gather all recent data about production of bio-oil by using liquefaction and pyrolysis method and their yield and properties from different types of biomass from previous research. Shortage of fossil fuels as well as environmental concern has encouraged governments to focus on renewable energy resources. Biomass is regarded as an alternative to replace fossil fuels. There are several thermo-chemical conversion processes used to transform biomass into useful products, however in this review article the focus has been made on liquefaction and pyrolysis method because the liquid obtained which is known as bio-oil is the main interest in this review article. Bio-oil contains hundreds of chemical compound mainly phenol groups which make it suitable to be used as a replacement for fossil fuels.

• Environmental Engineering Research
• /
• 제24권2호
• /
• pp.202-210
• /
• 2019

In order to maximize the utilization of sewage sludge, a waste from wastewater treatment facility, the residual sewage sludge generated after lipid and carbohydrate extraction for biodiesel and bioethanol production was used to produce bio-oil by pyrolysis. Thermogravimetric analysis showed that sludge pyrolysis mainly occurred between 200 and $550^{\circ}C$ (with peaks formed around 337.0 and $379.3^{\circ}C$) with the decomposition of the main components (carbohydrate, lipid, and protein). Bio-oil was produced using a micro-tubing reactor, and its yield (wt%, g-bio-oil/g-residual sewage sludge) increased with an increase in the reaction temperature and time. The maximum bio-oil yield of 33.3% was obtained after pyrolysis at $390^{\circ}C$ for 5 min, where the largest amount of energy was introduced into the reactor to break the bonds of organic compounds in the sludge. The main components of bio-oil were found to be trans-2-pentenoic acid and 2-methyl-2-pentenoic acid with the highest selectivity of 28.4% and 12.3%, respectively. The kinetic rate constants indicated that the predominant reaction pathway was sewage sludge to bio-oil ($0.1054min^{-1}$), and subsequently to gas ($0.0541min^{-1}$), rather than the direct conversion of sewage sludge to gas ($0.0318min^{-1}$).

• 한국응용과학기술학회지
• /
• 제28권4호
• /
• pp.431-437
• /
• 2011

Transparent liquid crystal gels with high oil content by fatty acid soap were investigated. The solubilization efficiency of the mineral oil was dependent on the process. The process of dropping water part into the solution of oil and surfactant was more efficient than the process of dropping water part into the surfactant solution and after that dropping oil. The fatty acid soap could not solubilize the high oil content, but under the certain range, addition of CDE (Coconut Diethanolamide), Arlacel 165 (Glyceryl Stearate/PEG-100 Stearate) and cetostearyl alcohol helped solubilize the high content oil. Also, the glycerin and water content had influence on the solubilization. Especially, higher oil content gel showed elastic feature.

• 한국응용과학기술학회지
• /
• 제32권1호
• /
• pp.148-156
• /
• 2015

시료의 입경 및 투입량 차이에 따른 바이오오일의 특성변화를 알아보기 위하여 0.5~2.0 mm 크기의 굴참나무(Quercus variabilis) 시료 300~900 g을 $465^{\circ}C$에서 1.6초 동안 급속열 분해하여 바이오오일을 제조하였다. 입경 및 투입량 차이에 따른 열분해 생성물의 수율변화에는 눈에 띠는 경향은 없었지만, 바이오오일 수율이 가장 많아 약 60.3~62.1%를 차지하였고, 미응축가스, 바이오차 순이었다. 바이오오일을 냉각관으로 응축하여 얻은 1차 바이오오일과 전기집진장치로 얻은 2차 바이오오일로 구분하여 수율을 측정한 결과, 1차 바이오오일의 수율이 2차 바이오오일 수율의 약 2배 이상을 나타내었다. 그러나 발열량은 2차 바이오오일이 1차 바이오오일 보다 약 2배 이상 높았으며, 최대 5,602 kcal/kg을 나타내었다. 1차 바이오오일의 수분함량이 20%이상으로 2차 바이오오일의 수분함량 10% 이하였다. 또한 2차 바이오오일의 원소분석 결과, 1차 바이오오일보다 탄소함량이 높고, 산소함량이 낮았기 때문에 수분함량과 원소조성 특성도 발열량에 영향을 미치는 것으로 판단된다. 바이오오일의 저장온도가 높을수록 또는 저장기간이 길수록 점도가 증가하며, 2차 바이오오일의 점도 증가 정도가 1차 바이오오일보다 컸는데, 저장기간 중에 바이오오일 성분 간의 화학적 결합에 의한 바이오오일의 고분자화가 진행되는 것으로 판단된다.

• 한국분무공학회지
• /
• 제2권3호
• /
• pp.44-50
• /
• 1997

Bio-diesel oil is a great possibility to solve the pollution problem caused by the exhaust gas from diesel engine vehicles. Recently the use of bio-oils in disel engines has received considerable attention to the forseeable depletion of world oil supplies. So, Bio-diesel oil has been attracted with attentions as an alternative and clean energy source. The objective of this paper is to experimentally investigate the characteristic of performance using light oil, rice-bran oil, heated rice-bran oil, rice-bran oil treated with ultrasonic energy. We included rice-bran oil and applied ultrasonic energy to highly viscous bio-oils. These methods seems to have never been tried yet. The final data may be able to be applicated for the design of the diesel engine using an alternative fuel.

• Journal of Biosystems Engineering
• /
• 제43권1호
• /
• pp.14-20
• /
• 2018

Purpose: The purpose of this study was to investigate the performance of a vacuum pyrolysis system, to analyze bio-oil characteristics, and to examine the applicability for farm-scale capacity. Methods: The biomass was pyrolyzed at 450, 480, and $490^{\circ}C$ on an electric heat plate in a vacuum reactor. The waste heat from the heat exchanger of the reactor was recycled to evaporate water from the bio-oil. The chemical composition of the bio-oil was analyzed by gas chromatography-mass spectrometry (GC-MS). Results: According to the analysis, the moisture content (MC) in the bio-oil was approximately 9%, the high heating value (HHV) was approximately 26 MJ/kg, and 29 compounds were identified. These 29 compounds consisted of six series of carbohydrates, 17 series of lignins, and six series of resins. Conclusions: Owing to low water content and the oxygen content, the HHV of the bio-oil produced from the vacuum reactor was higher by about 6 MJ/kg than that of the bio-oil produced from a fluidized bed reactor.

• 동력기계공학회지
• /
• 제17권6호
• /
• pp.149-155
• /
• 2013

Since bio-diesel oil has a merit that it satisfies both demand of substitution for fossil fuel and reduction in carbon dioxide emission, it is widely used in diesel engines by blending in gas oil in small quantity. It is needed to reduce in NOx emission in some way or others if blending ratio of bio-diesel oil is going to increase, because it is demerit that bio-diesel oil emits more NOx emission than gas oil. In this study, it was accomplished to optimize 3 factors what effect on NOx emission as blending ratio of bio-diesel oil, injection timing and common rail pressure with an introduction of a design of experiments, in order to minimize a number of tests. It was cleared that to introduce the design of experiments was very available in NOx optimization.