• Journal of the Korean Society of Combustion
• /
• v.20 no.1
• /
• pp.15-23
• /
• 2015

This paper presents the results of field demonstration for fuel switching to bio-fuel oil in 4 commercial heavy oil fired power plants. The 100% fuel switching field demonstration was successfully carried out in two tangential-firing boilers at a capacity of 75 and 100 MWe respectively without major equipment retrofit, and also 25% bio-fuel oil blending for two opposite firing boilers at a capacity of 350 and 400 MWe respectively. Despite the low density and heating value, the bio fuel was successfully replaced heavy fuel oil at the full load by only adjusting operational parameters. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. In pollutants emission, a major reductionin SOx as well as 10-20% reduction in NOx were achieved by the fuels witching. On the other hand, boiler efficiency was slightly underestimated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.53-58
• /
• 2013

In order to judge that non-esterified soybean oil could be used on diesel engine with electronic control of fuel injection system, The test of combustion performance using only gas oil, gas oil blended with esterified bio-diesel oil 5% and non-esterified soybean oil 5% were carried out. It is noticed that most performances of gas oil blended with esterified bio-diesel oil 5% and non-esterified 5% have similar characteristics but non-esterified bio-diesel oil 5% emitted smaller NOx, resulting from fuel NO.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.359-368
• /
• 1996

The performance and exhaust emissions of a diesel engine using light oil, heated, rice-bran oil , heated rice-bran oil treated with ultrasonic wave, used frying oil, use frying oil treated with ultrasonic wave, used frying oil, used frying oil treated with ultrasonic wave, methyl esters of rice-bran oil and used frying oil have been compared. All the fuels performed satisfactorily in a precombustion chamber-type diesel engine without injection pump recalibration or any engine modification at the range of engine speed from 1600 to 2800 rpm at its full load during a sort period , with the rice-bran oil and rice-bran oil treated with ultrasonic wave requiring somewhat preheating when ambient temperature was below 15$^{\circ}C$. General performance and emission characteristics of light oil and bio-oils were comparable , with the bio-oil based fuels giving very low SO$_2$ and lower smoke readings.

• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.340-344
• /
• 2007

Catalytic upgrading of pyrolytic bio-oil produced from Japanes Larch was carried out over MCM-41 catalyst. Oil with enhanced stability was produced by the MCM-41 catalyst due to transform oxygen known as a main cause for the instability of bio-oil into $H_2O$, CO and $CO_2$. In addition, the MCM-41 catalyst produced the larger amount of phenolic compounds in the pyrolytic bio-oil product compared with that in the bio-oil produced without catalyst. Especially, the catalytic activity of Al-MCM-41 for the bio-oil upgrading was higher than that of Si-MCM-41 because Al-MCM-41 has the larger amount of acid sites. Also, the better reforming result was obtained when pyrolytic bio-oil vapor passed through catalytic layer rather than Japanese Larch was mixed with catalyst directly.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.3
• /
• pp.588-598
• /
• 2015

Recently, the government is actively promoting the RFS(Renewable Fuel Standards) and RPS(Renewable Portfolio Standards). Therefore, the importance of renewable energy fuel is being highlighted more than ever. Now is the time required active research in Korea. Since power bio-fuel oil demonstration project is underway dissemination to meet RPS quota. In this study, we investigated emission performance to make the performance standard draft of bio-fuel oil. In addition, the quality properties of the fuel oil and bio-oil, and after combustion in industrial boilers and compared the amount of exhaust gas. It was reduced emissions of bio-oil in industrial boilers due to bio-fuel properties as compare with fuel oil.

• Tribology and Lubricants
• /
• v.32 no.6
• /
• pp.183-188
• /
• 2016

Engine oil plays an important role in the mechanical lubrication and cooling of a vehicle engine. Recently, engine development has focused on the adoption of gasoline direct injection (GDI) and turbocharging methodology to achieve high-power and high-speed performance. However, oil dilution is a problem for GDI engines. Oil dilution occurs owing to high-pressure fuel injection into the combustion chamber when the engine is cold. The chemical components of engine oil are currently developed to accommodate gasoline fuel; however, bio-alcohol mixtures have become a recent trend in fuel development. Bio-alcohol fuels are alternatives to fossil fuels that can reduce vehicle emissions levels and greenhouse gas pollution. Therefore, the chemical components of engine oil should be improved to accommodate bio-alcohol fuels. This study employs a 2.0 L turbo-gas direct injection (T-GDI) engine in an experiment that dilutes oil with fuel. The experiment utilizes a variety of fuels, including sub-octane gasoline fuel (E0) and a bio-alcohol fuel mixture (Ethanol E3~E7). The results show that the lowest amount of oil dilution occurs when using E3 fuel. Analyzing the diluted engine oil by measuring density and moisture with respect to kinematic viscosity shows that the lowest values of these parameters occur when testing E3 fuel. The reason is confirmed to influence the vapor pressure of the low concentration bio-alcohol-fuel mixture.

• Journal of the Korean Society of Food Culture
• /
• v.19 no.1
• /
• pp.61-69
• /
• 2004

The shelf-life of Yugwa(Busuge) is very short because of the low oxidative stability of soybean oil which is conventionally used as the frying oil of Yugwa base with high porous structures. To identify the possibility of replacing soybean oil with palm oil whose oxidative stability is high, POV(peroxide value), AV(acid value), colorness (L. a and b), hardness and sensory characteristics during storage of the Yugwa base fried with the soybean oil and palm oil stored in the anaerobic packaging or the aerobic packaging at 10 and $30^{\circ}C$ for 75 days were measured. POV and AV of the Yugwa base fried with palm oil were significantly lower than those of Yugwa fried with the soybean oil. Hardness and colorness were not different each other and, sensory evaluation was slightly higher than that fried with soybean oil. Lipid absorption amount was not significantly different between the Yugwa base fried with palm oil and the one fried with soybean oil.

• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.12-19
• /
• 2006

Rice straw is one or the main renewable energy sources in Korea. Bio-oil is produced from rice straw with a lab-scale equipment mainly with a fluidized bed and a char removal system. It was investigated how the reaction temperature affected the production of bio-oil and the efficiency of a char removal system. To elucidate how the temperature depended on the production of bio-oil, experiments were conducted at $466^{\circ}C,\;504^{\circ}C\;and\;579^{\circ}C$, respectively. The mass balance was established in each experiment, and the produced gas and oil were analyzed with the aid of GCs and a GC-MS system. The char removal system is composed of a cyclone and a hot filter. Tn the experiments, we observed that the production of bio-oil was decreased with temperature, and the bio-oil contained very useful chemicals.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.6
• /
• pp.712-720
• /
• 2017

As Korean government has activated the renewable portfolio standard (RPS) since 2012, producers have been seeking and using the various renewable resources to meet the RPS quota. One of these efforts, Power Bio-Fuel oil demonstration project is being conducted to check the operability and compatibility with fossil fuel, Fuel oil (B-C) from 2014. The oil is a mixture of vegetable oil and animal fat or fatty acid ester of them and should satisfy some specification to use the power generation. The oil's quality and combustion characteristics are different from conventional oil, Fuel oil (B-C) in current power plant facility. In this study, it was investigated the storage stability and malodor intensity of Bio-Fuel oil.

• Clean Technology
• /
• v.26 no.1
• /
• pp.79-87
• /
• 2020

The bio-oil produced from the fast pyrolysis of lignocellulosic biomass contains a high amount of oxygenates, causing variation in the properties of bio-oil, such as instability, high acidity, and low heating value, reducing the quality of the bio-oil. Consequently, an upgrading process should be recommended ensuring that these bio-oils are widely used as fuel sources. Catalytic fast pyrolysis has attracted a great deal of attention as a promising method for producing upgraded bio-oil from biomass feedstock. In this study, the fast pyrolysis of tulip tree was performed in a bubbling fluidized-bed reactor under different reaction temperatures, with and without catalysts, to investigate the effects of pyrolysis temperature and catalysts on product yield and bio-oil quality. The system used silica sand, ferric oxides (Fe₂O₃ and Fe₃O₄), and H-ZSM-5 as the fluidized-bed material and nitrogen as the fluidizing medium. The liquid yield reached the highest value of 49.96 wt% at 450 ℃, using Fe₂O₃ catalyst, compared to 48.45 wt% for H-ZSM-5, 47.57 wt% for Fe₃O₄ and 49.03 wt% with sand. Catalysts rejected oxygen mostly as water and produced a lower amount of CO and CO₂, but a higher amount of H₂ and hydrocarbon gases. The catalytic fast pyrolysis showed a high ratio of H₂/CO than sand as a bed material.