• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1212-1220
• /
• 2000

Bi-2223 초전도체계에서 석출물을 flux-pinning center로 이용할 수 있는지 가능성을 타진하기 위하여 $Bi_{1.8}$P $b_{0.4}$S $r_{2}$C $a_{2.2}$C $u_3$ $O_{8}$ 조성을 가진 Bi-2223/Ag 선재를 반응온도, 산소분압, 시간 등을 변화시키면서 열처리를 행하였다. 열처리 후 석출물들은 XRD, SEM, TEM, EDS로 분석하였다. Bi-2223 모상내의 (Ca, Sr)$_2$(Pb,Bi) $O_4$, B $i_{0.5}$ P $b_3$S $r_2$C $a_2$Cu $O_{12+}$$\delta$/ (3221)와 같은 2차상들의 크기와 분포는 2223 입자들의 연결성을 파괴하지 않고 열처리 조건에 의해서 조절할 수 있었다. 서냉 열처리가 된 시편은 임계전류밀도( $J_{c}$)값이 증가하였는데, 이는 2223 입자내 나노미터 크기로 형성된 석출물들이 flux-pinning sites로 작용한 것으로 추정된다.다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2000.02a
• /
• pp.6-8
• /
• 2000

The critical current density, Jc, of superconductor tape significantly depends on microstructural evolution during mechanical deformation. In this study, we fabricated Bi-2223 superconductor tape by PIT technique, and investigated mechanical properties of mono- and 61-filamentary tapes and their joined tapes. The strength of mono-filament tape was higher than those of 61-filament tape was higher than those of 61-filament tape, respectively. On the other hand, elongation of mono-filament tape, respectively. On the other hand, elongation of mono-filament tape was lower than 61 filament tape. The joined tapes shows lower strength and irreversible strain than those of unjoined tapes. The reduced strength and irreversible strain for joined tape is probably related to the induced damages such as irregular interface and Ag-instrusion in the transition region which acts as a stress concentration.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.281-288
• /
• 1994

According to spread volume of B(BiPbCuO) layer, composition ratio and each stage of sintering process, we studied stability of high Tc superconductor phase and generation and growth movement of superconducting phase. The dual layer composed of SrCaCuO and BiPbCuO compound were prepared to develop the Bi-2223 superconductor[108K] through interaction and diffusion during sintering process. The dual layer samples were sintered at 830.deg. C for 0-210 hours. From the result, the optimum conditions were : spread volume(A:B=1:0.6), sintering time(210h) and composition ratio(A:S $r_{2}$C $a_{2}$C $u_{2}$- $O_{x}$, B:B $i_{1.9}$P $b_{0.5}$C $u_{3}$ $O_{y}$) at 830.deg. C.. C.C.C.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.137-139
• /
• 2003

The relationship between magnetic properties of BiPbSrCaCuO superconductor and externally applied magnetic field was studied to develop a magnetic field polarity sensor. The behavior was related to the magnetic flux trapped in the superconductor, which penetrates through the material by the external magnetic field. Some portion of the superconductor was changed to a normal state by the trapped magnetic flux. Electrical characteristics of the superconductor with trapped magnetic flux were extremely sensitive to the external magnetic field and showed different responses depending on the direction of the magnetic field.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.31-35
• /
• 1990

In the ($Bi_{1-x}Pb_{x}$)$_2$$Sr_2$$Ca_2$$Cu_{3.6}$$O_{y}$ (x=0∼0.5) superconductors, DTA and XRD-pattern analyses were performed to obviousely define optimal calcining and sintering temperature. And, understanding behaviors of High-Tc phase with preparation condition of superconductors, that is, calcining and sintering temperature, sintering time, and variation of Pb contents, in order to make single phase of superconductor, microstructure and its composition were analyzed with SEM, XRD, and EDAX. continuously, the cause of phase transition was define with synthetically studying mutural relation between measured electrical resistivity and current density. Also, in order to design enhancement of critical current density, Jc required for realization, samples varied with pressing condition were made, and measured its, Jc.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.252-254
• /
• 2003

A magnetic field sensor is fabricated with superconducting ceramics system. The sensor at liquid nitrogen temperature shows the increase in electrical resistance by applying magnetic field. Actually, the voltage drop across the sensor is changed from zero to a value more than $100{\mu}V$ by the applied magnetic field. The change in electrical resistance depends on magnetic field. The sensitivity of this sensor is 2.9 ohm/T. The increase in electrical resistance by the magnetic field is ascribed to a modification of the Josephson junctions due to the penetrating magnetic flux into the superconducting material.

• Progress in Superconductivity
• /
• v.14 no.1
• /
• pp.1-10
• /
• 2012

We fabricated a closed coils by using resistive-joint method and the joint resistance of the coils were estimated by field decay technique in liquid nitrogen. We used the Runge-kutta method for the numerical analysis to calculate the decay properties. The closed coil was wound by $(Bi,Pb)_2Sr_2Ca_2Cu_3O_x$/Ag tape. Both ends the tape were overlapped and soldered to each other. The current was induced in a closed coils by external magnetic flux density. Its decay characteristic was observed by means of measuring the magnetic flux density generated by induced current at the center of the closed coil with hall sensor. The joint resistance was calculated as the ratio of the inductance of the loop to the time constants. The joint resistances were evaluated as a function of critical current of loop, contact length, sweep time, and external magnetic flux density in a contact length of 7 cm. It was observed that joint resistance was dependent on contact length of a closed coil, but independent of critical current, sweep time, and external magnetic flux density. The joint resistance was measured to be higher for a standard four-probe method, compared with that for the field decay technique. This implies that noise of measurement in a standard four-probe method is larger than that of field decay technique. It was estimated that joint resistance was $8.0{\times}10^{-9}{\Omega}$ to $11.4{\times}10^{-9}{\Omega}$ for coils of contact length for 7 cm. It was found that 40Pb/60Sn solder are unsuitable for persistent mode.

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.41-45
• /
• 2004

Polycrystalline Tl-1223 superconductors with a chemical composition of (Tl, Pb, Bi)TEX>$ (Sr, Ba)<_2$$Ca_2$$Cu_3$$O_{x}$ were synthesized by the solid state reaction method. The optimum chemical composition was $Tl_{0.8}$ $Pb_{0.2}$ $Bi_{0.2}$ $Sr_{1.8}$ $Ba_{0.2}$ $Ca_{2.2}$ $Cu_3$$O_{x}$ And the optimum sintering temperature and time were $905^{\circ}C$ and 7.5h, respectively. The sample was evaluated for their superconducting properties by magnetization measurement. The critical temperature $T_{c}$ is 120 K and the critical current density $J_{c}$ (T=5K, 0T) is estimated to be ∼ $10^{5}$ A/$\textrm{cm}^2$ for $Tl_{0.8}$ $Pb_{0.2}$ $Bi_{0.2}$ $Sr_{1.8}$ $Ba_{0.2}$ $Ca_{2.2}$$Cu_3$$O_{x}$ .

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.2
• /
• pp.5-9
• /
• 2023

The effect of La_0.7Sr_0.3MnO₃ (LSMO) addition on the superconducting property of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ ((Bi, Pb)-2223) polycrystalline samples was studied. LSMO (0.3 wt.% to 2.0 wt.%) added (Bi, Pb)-2223 samples were prepared by using a solid-state reaction method. The XRD analyses show that as the LSMO addition increases, the volume fraction of the Bi-2223 phase is gradually decreased. The critical temperature (T_c) exhibits a gradual decrease with a single transition as the LSMO amount increases up to 1.0 wt.%, but a further addition of LSMO induces an abrupt decrease of T_c with a dual transition. The analyses on the local structure of the CuO₂ plane from the X-ray absorption fine structure (EXAFS) measurements showed that for the samples with low concentration of LSMO up to 1.0 wt.%, the Cu-O bond length and the CuO₂ plane ordering do not degrade from the values of pure (Bi, Pb)-2223, while they get worsen with a further increase of LSMO addition. These results open up the possibility of LSMO as artificial pinning centers of the (Bi, Pb)-2223 system for power application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.221-223
• /
• 1999

In this work, samples were manufactured variously by changing conventional calcining and sintering conditions and we tried the utilization by making the heat treatment time, which is demanded to high-Tc phase formation, much shorter. We found out optimal heat treatment conditions with the analysis on formation process at superconducting phase in term of the change of calcining and sintering time and then, examined X-ray diffraction(XRD) patterns, scanning electron microscope(SEM) measurement and energy dispersive X-ray spectrometer(EDX) of the samples manufactured under heat treatment conditions which we suggest here. As a result, 2223 high-$T_c$, phase of (Bi,Pb)SrCaCuO superconductor starting with ($Bi_l$ xPbx,)$_2$$Sr_2$$Ca_2$$Cu_3$$O_y$, composition was formed from 1 hr sintering sample at temperature nearby melting point and also the completed sample with calcining and sintering time of 9 hr was formed high-$T_c$.low-$T_c$ phase appearing in sight above the critical temperature of liquid $N_2$.