• Fashion & Textile Research Journal
• /
• v.8 no.5
• /
• pp.585-590
• /
• 2006

In the variation of physical properties of adhesive fabrics, the objective of this study is to analyze fitness of fusible interlining to four sorts of fabrics for men's suit with various structural parameters. Four fusible interlinings are used for adhering to fabrics for men's suit. Mechanical properties of these 16 adhesive fabrics fused with these interlinings are measured by KES-FB system for analysing appearance and wearing properties of garments and for examining the fitness of fusible interlining to the fabrics for men's suit. The variation of bending property for adhesive fabrics are found to be higher in the order of interlining 1(Cotton30/Rayon70, plain), interlining 2(Polyester30/Rayon70, warp knit), interlining 4(Polyester, shingosen fabrics with drawing textured yarn) and interlining 3(Polyester, double dot coating interlining). The variation of adhesive effect shows the same results with bending property and shows negative relation with extensibility in weft direction per extensibility in warp direction(EM2/EM1). The variation of peel strength of adhesive fabrics, woolen fabrics in the case of face fabrics and interlining 3 in the case of interlining shows the largest value respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.4
• /
• pp.258-265
• /
• 2016

A flexible riser consists of several layers which have different materials, shapes and functions. The layers designed properly can take the design load safely, and each property of layer provides a complexity of flexible riser. Such complexity/unit-property is an input for global analysis of flexible riser. There are several approaches to calculate the complexity of flexible riser, those are experimental, numerical and theoretical methods. This paper provides a complexity from numerical and theoretical analysis for 2.5 inch flexible riser of which details and the experimental data are already produced under tension, external pressure, and bending moment. In addition, comparison of stiffness and stress are also provided. Especially, analysis of stress could lead to researches on ultimate strength or fatigue strength of flexible risers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.360-366
• /
• 2013

For conventional electrical actuators, the materials are mainly made up of metals, which mean they are prone to corrosion and electrical sparking. Replacing these systems with polymer metal composite based materials can be solved both problems. Considering their excellent electromechanical property, low device fabrication cost, light weight, and good electrical conductivity, the actuator based on ionic polymer metal composite (IPMC) was fabricated using Nafion film, NaOH 0.1 molar solution, and Au electrode. IPMCs exhibit good electrostatic property which means they can in principle be used in making actuators based on electromechanical motions. The resistance measurements of Nafion film after soaking in NaOH and deionized water were demonstrated and compared each other. The result of sample soaked in NaOH showed better electrical conductivity than in deionized water. The fabricated IPMC actuator exhibits a large deformation of bending displacement of approximately 9 mm with applied low AC voltage 6.89 V at 2.84 Hz. The result of computer simulation was also very similar and shown as a bending displacement of 8.6085 mm.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.5
• /
• pp.504-513
• /
• 2021

In this study, cross-laminated wood panels were manufactured with four softwoods and three hardwoods with the goal of efficiently predicting the static strength performance using dynamic modulus of elasticity (MOE) and simultaneously revealing the dynamic performance of cross-laminated wood panels. The effect of the density of the species on the dynamic MOE of the laminated wood panels was investigated. Moreover, the static bending strength performance was predicted nondestructively through the correlation regression between the dynamic MOE and static bending strength performance. For the dynamic MOE, the parallel- and cross-laminated wood panels composed of oriental oak showed the highest value, whereas the laminated wood panels composed of Japanese cedar showed the lowest value. In all types of parallel- and cross-laminated wood panels, the density dependence was confirmed, and the extent of the density dependence was found to be greater in the P_⊥ and C_⊥ types with perpendicular-direction laminae in the faces than in the P_∥ and C_∥ types with longitudinal-direction laminae in the faces. Our findings confirmed that a high correlation exists at a significance level of 1% between the dynamic modulus and static bending modulus or bending strength in all types of laminated wood panels, and that the static bending strength performance can be predicted through the dynamic MOE.

• Journal of Korea Foundry Society
• /
• v.22 no.6
• /
• pp.281-287
• /
• 2002

In order to investigate the variation of microstructure and property of the Electro-slag Remelted M2 steel, microstructure observation, hardness, and bending test were performed by using optical microscope. SEM/EDS, rockwell hardness tester, charpy impact tester and bending tester, respectively. It was revealed that the number of inclusions and content of gas elements(S, O, N) in M2 steel fabricated by ESR process decreased markedly compared to those of AIM. It seems to be due to refining effect of ESR process. The volume fraction of carbides in quenched and tempered specimens after austenitizing at 1150$^{\circ}C$ and 1240$^{\circ}C$ was measured. The volume fraction of grain boundary carbides were found to be similar for both specimens. However, The volume fraction of carbides in grain decreased with an increase of austenitizing temperature. When specimen was austenitized at 1150$^{\circ}C$, grain boundary carbides showed needle like morphology. But, the carbides were broken with an increase of austenitizing temperature. The specimen austenitized at 1240$^{\circ}C$ showed higher hardness and lower bending strength compared to that of 1150$^{\circ}C$. As expected, toughness increased with sub-zero quenching treatment.

• Journal of Powder Materials
• /
• v.11 no.5
• /
• pp.412-420
• /
• 2004

The purpose of the present study is to determine an optimum composition using cheaper powders keeping with high performance of hard rock cutting diamond saw blade. With 50Fe-20(Cu . Sn)-30Co specimen, a part of Co was replaced by Ni(5%, 10%, and 15%, respectively). These specimens were hot pressed and sintered for predetermined time at various temperature. Sintering is performed by two different methods of temperature controlled method and specimen dimension controlled method. In order to determine the property of the sintered diamond saw blade, 3 point bending tester, X-ray diffractometer, and SEM were used. As the Co in the bond alloy was replaced by Ni, the hardness of the specimen increased. Thus the 50Fe-20(CuㆍSn)-15Co-15Ni specimen showed the maximum hardness of 104(HRB). The results of 3 point bending test showed that flexure strength decreased along with increase in Ni content. This is attributed to the formation of intermetallic compound(Ni$_{x}$Sn) determined by X-ray diffraction. The fracture surface after 3 point bending test showed that diamond was fractured in the specimen containing 0%, 5%, and 10%Ni, and the fracture occurred at the interface between diamond and matrix in the specimen containing 15%Ni. The cutting ability test showed that the abrasive property was not changed in the specimen containing 0%, 5%, and 10%Ni. The optimum composition determined in this study is 50Fe-20(CuㆍSn)-20Co-10Ni.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1022-1034
• /
• 1999

A relation between composition and properties of Na2O-Al2O3-SiO2 glasses was investigated with application of the extreme vertical design. Properties investigated in this study include glass transition temperature density refractive index thermal expansion electrical conductivity bending strength and hardness, Most of the quadratic models fitted on property data were statistically significant. The properties estimated from the fitted equation agreed well with the measured properties. The estimated properties were compared with those reported by other investigators. Additional composition except for those of extreme vertices were needed to yield a slightly better result for the simple system such as a temary system. In addition an optimal composition on each property could be calculated by using optimization technique on result obtained from the fitted quadratic models.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.68-72
• /
• 2001

In order to effectively use the waste wood, two types of woodceramics chip tile were made from woodceramics chip, gravel, zeolite and additions. The woodceramics chip was made from branch of apple tree (Malus pumila Mill.) Snow melting property, bending strength and compressive strength of woodceramics chip tile were tested according to the mixing rate of woodceramics chip. Snow melting properties of woodceramics chip tile increased after additions treatment but mechanical properties were reduced significantly after additions treatment. The results indicate that the additions are effective for snow melting property but negative effect on mechanical properties.

• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.494-499
• /
• 2010

Knitted fabrics are very popular for their numerous advantages such as greater comfort, attractive garment appearance, better fit on the body, etc. In this study, we investigated the mechanical properties and abrasion property of warp knitted fabrics for footwear which treated with several softeners to improve abrasion resistance. The antistatic softener among the various softeners showed high improvement in abrasion resistance. Among the mechanical properties with treating conditions, WT (tensile energy), G (shear stiffness), B (bending rigidity) increased as treating timeincreased. But the other mechanical properties were little changed with treating concentration.

• 한국기계연구소 소보
• /
• s.13
• /
• pp.3-13
• /
• 1984

Fatigue failure of axle housing could cause many injuries and much financial loss. This challenges the engineer to improve design decisions involving fatigue. Endurance evaluation of axle housing is great interest to auto-mobile manufacturers for the sake of safety and reliability. Axle housing is subjected to gross vehicle weight(G.V.W)as mean load and alternating load. Theoretical design diagram involving mean and alternating stresses is used for the evaluation of axle housing fatigue endurance with the equivalent stress of fatigue critical area on the axle housing. Four point bending fatigue tests on axle housing with constant amplitude loading at approximately R=0 were performed with 50 ton servohydraulic strucural fatigue testing machine developed at KIMM. Specimens were made with the same material STKM 13B as the axle housing and tested to obtain S_N data. Five specimens of STKM 13B were tested at 253.61 MPa and weibull distribution was obtained at the same stress level. Material data and structural data were compares and fatigue stress property factor and fatigue life property factor were obtained.