• Geomechanics and Engineering
• /
• 제19권4호
• /
• pp.329-342
• /
• 2019

In this paper, the effect of a group of sand columns in the loose soil bed using triaxial tests was studied. To investigate the effect of geotextile reinforcement type on the bearing capacity of these sand columns, Vertical encased sand columns (VESCs) and horizontally reinforced sand columns (HRSCs) were used. Number of sixteen independent triaxial tests and finite element simulation were performed on specimens with a diameter of 100 mm and a height of 200 mm. Specimens were reinforced by either a single sand column or three sand columns with the same area replacement ratio (16%) to evaluate the Influence of the column arrangement. Effect the number of sand columns, the length of vertical encasement and the number of horizontal reinforcing layers were investigated, in terms of bearing capacity improvement and economy. The results indicated that the ultimate bearing capacity of the samples with three ordinary sand columns (OSCs) is eventually about 11% more than samples with an OSC. Also, comparison of the column reinforcing modes showed that four horizontal layers of geotextile achieved similar performance to a vertical encasement geotextile at the 50% of the column height, from the viewpoint of strength improvement, while from the viewpoint of economy, the geotextile needed for encasing the single column is around 2.5 times of the geotextile required for four layers.

• 한국정밀공학회지
• /
• 제31권8호
• /
• pp.715-720
• /
• 2014

Recently, surface texturing technologies have been widely used in lots of industries to increase the machinery efficiency. In this research, the lubrication characteristics of a crank shaft pin turner bearing with dimples were studied. When increasing the dimples, the load carrying capacity due to the increased pressure was increased because those have sealing effects. Also, the run-out error of the bearing was decreased. Therefore, it is important to consider the depth, the number and the distribution of dimples when designing the hydrostatic journal bearing.

• 한국생산제조학회지
• /
• 제21권5호
• /
• pp.741-746
• /
• 2012

The increase of energetic efficiency in plane bearing is getting more important in the transfer mechanism of semi-conductor and display panel manufacturing processes. To accomplish this objective, the technique of surface texturing on bearing surface has recently emerged as one of the most effective candidates. In this study, the effects of various pattern parameters on two bearing performance indices(load carrying capacity and effective friction coefficient) are investigated through a semi-analytic method, i.e., the 2-dimensional Reynolds equation incorporated into the finite difference scheme. Here, cavitation effect is also taken into account by employing an appropriate numerical scheme. In this study, the patterns in the textured surface are composed of a series of semi-spheres or semi-ellipsoids in shape. The effects of their size and number density on the performance indices are examined through the performance of various numerical experiments. Also, the effects of the anisotropy of the semi-ellipsoidal pattern on the bearing's lubrication characteristics are investigated and discussed.

• Progress in Superconductivity
• /
• 제12권1호
• /
• pp.27-31
• /
• 2010

A superconductor flywheel energy storage system (SFES) is an electro-mechanical battery which transforms electrical energy into mechanical energy for storage, and vice versa. Many aspects of the quasi-static behavior of flywheel rotors still need to be studied closely, and the rotors require a stable and highly efficient supporting system such as high temperature superconductor (HTS) bearings, which offer dynamic stability without the use of active control. Quasi-static properties of HTS bearings in the radial direction provide data to solve problems which may occur in a running system. Since stiffness in countering rotor vibration is the main parameter for designing an HTS bearing system, we investigated the quasi-static properties of the magnetic force between permanent magnets(PMs) and HTS bulks in the radial direction. We measured radial stiffness, and discovered that bearing stiffness varied greatly depending on the number of active HTS bulks. This is valuable data for predicting the change in stiffness during partial HTS bearing failure. The quasi-static test results are used for optimal design and performance prediction for the 100 kWh class superconductor bearing.

• Tribology and Lubricants
• /
• 제33권6호
• /
• pp.309-314
• /
• 2017

This paper presents a theoretical investigation of the dynamic characteristics of externally pressurized air pad bearings with closed loop grooves. These grooves are made on the surface of bearings to reduce the number of supply holes so that manufacturing costs can be reduced. The semi-implicit method is applied to calculate the time varying pressure profile on the air bearing surface owing to the advantages of numerical stability and fast time tracing characteristics. The static pressure of the groove bearings is much higher than that without grooves, so the groove bearings can provide high load carrying capacity. The equation of motion considering vertical motion and tilting motion are also solved using the Runge-Kutta 4th order method. By combining the semi-implicit method and the Runge-Kutta method, fast calculations of the dynamic behavior of the air bearing can be achieved. The variations of bearing reaction force, air film reaction moment, height, and tilting angle are investigated for the step force input, which is 20% higher than the bearing reaction, when the nominal clearance is 6 mm. The effect of the groove width and the groove depth are investigated by calculating the dynamic behavior. The possibility of the air hammering with the depth of the groove is found and discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.52-57
• /
• 2001

In this paper, the optimum designs of air-bearing surface(ABS) are achieved effectively by using reduced basis concept which can reduce the number of design variables although the design space is distended. Generally, the optimization method is more effective than the trial and error. However, the efficiency of the former is largely dependent on the number of the design variables. In order to reduce the number of design variables and increase the efficiency, reduced basis concept is applied. We can define the desired design as a linear combination of basis designs using this concept. From this optimization method with reduced basis concept, we easily obtain the optimum designs of ABS whose target flying heights are 25, 20, 15 nm.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.283-287
• /
• 2007

Permanent-magnet (PM) passive bearings use the repulsive forces between the rotor and the stator magnets for the bearing function. It is desirable that the stiffness of the bearing is maximized with the given volume of the magnet. The stiffness is affected by the magnet strength, the number of layers, and the magnetization patterns. Previously, finite-element method (FEM) has been used to maximize the stiffness of the bearing. In this paper, we used the equivalent current sheet method to calculate the stiffness. The validity of this approach is checked against FEM results. The optimized bearing is applied to a micro flywheel energy storage system.

• Tribology and Lubricants
• /
• 제26권1호
• /
• pp.1-6
• /
• 2010

In the last decade, laser surface texturing (LST) has emerged as a viable option of surface engineering. Many problems related with mechanical components such as thrust bearings, mechanical face seals and piston rings, etc, LST result in significant improvement in load capacity, wear resistance and reduction in friction force. It is mainly experimentally reported the micro-dimpled bearing surfaces can reduce friction force, however, precise theoretical results are not presented until now. In this paper, a commercial computational fluid dynamics(CFD) code, FLUENT is used to investigate the lubrication characteristics of a parallel thrust bearing having 3-dimensional micro-dimple. The results show that the pressure, velocity and density distributions are highly affected by the location and number of dimple. The numerical method and results can be use in design of optimum dimple characteristics, and further researches are required.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.101-107
• /
• 2008

In this paper, the features extracted from vibration time signals are used to detect the bearing fault condition. The decision tree is applied to diagnose the bearing status, which has the benefits of being an expert system that is based on knowledge history and is simple to understand. This paper also suggests a genetic algorithm (GA) as a method to reduce the number of features. In order to show the potentials of this method in both aspects of accuracy and simplicity, the reduced-feature decision tree is compared with the non reduced-feature decision tree and the PCA-based decision tree.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권1호
• /
• pp.59-70
• /
• 1991

Rupture of lubricant film, thermal characteristics, and variation of viscosity are very important factors to evaluate the performance of journal bearing. Variation of external conditions, load or rotational speed, largely influence these facters. For example, if rotational speed increases lubricant bulk temperature increases and viscosity drops. In this paper the effect of rotational speed variation on the characteristics of lubricant film in a journal bearing is investigated by experiment and theoretical analysis. It has been measured number of lubricant film rupture and lubricant bulk temperature form journal bearing which have been established at the various operating speed of shaft. The range of speed variation is from 900rpm to 2100rpm. Theoretical analysis has been carried out for rupture of lubricant film and thermal characteristics, and these results are compared with experimental results.