• 한국자원식물학회지
• /
• 제18권3호
• /
• pp.462-469
• /
• 2005

Effects of proton beam irradiation on seed germination and growth pattern of tobacco (Nicotiana tabacum L. cv. BY-4; N. plumbaginifolia) and rice (Oryasativa L.) plants were estimated to develop the efficient conditions of irradiation. Seed germination rate was decreased by increasing the proton beam the current and the beam irradiation time in both tobacco and rice seeds. The beam irradiation conditions showing $50\%$ germination were over 60 sec at 10 nA, approximately 5 sec at 100 nA and at 500 nA beam current in tobacco seeds. And the conditions of $50\%$ germination were 60 sec at 10 nA, and 100 nA and 30 sec at 500nA in rice (cv. Dongjin 1) seeds. The growth of irradiated plants was decreased, but significant difference in morphological changes was not observed by the proton beam treatment. The proton beam is able to use as a mutagen, but some of the factors including beam size and beam detector-system must be established for efficient usage of the beam.

• Nuclear Engineering and Technology
• /
• 제36권4호
• /
• pp.357-363
• /
• 2004

A prototype long pulse ion source was developed, and the beam extraction experiments of the ion source were carried out at the Neutral Beam Test Stand (NBTS) of the Korea Superconducting Tokamak Advanced Research (KSTAR). The ion source consists of a magnetic bucket plasma generator, with multi-pole cusp fields, and a set of tetrode accelerators with circular apertures. Design requirements for the ion source were a 120kV/65A deuterium beam and a 300 s pulse length. Arc discharges of the plasma generator were controlled by using the emission-limited mode, in turn controlled by the applied heating voltage of the cathode filaments. Stable and efficient arc plasmas with a maximum arc power of 100 kW were produced using the constant power mode operation of an arc power supply. A maximum ion density of $8.3{\times}10^{11}\;cm^{-3}$ was obtained by using electrostatic probes, and an optimum arc efficiency of 0.46 A/kW was estimated. The accelerating and decelerating voltages were applied repeatedly, using the re-triggering mode operation of the high voltage switches during a beam pulse, when beam disruptions occurred. The decelerating voltage was always applied prior to the accelerating voltage, to suppress effectively the back-streaming electrons produced at the time of an initial beam formation, by the pre-programmed fast-switch control system. A maximum beam power of 0.9 MW (i.e. $70\;kV{\times}12.5\;A$) with hydrogen was measured for a pulse duration of 0.8 s. Optimum beam perveance, deduced from the ratio of the gradient grid current to the total beam current, was $0.7\;{\mu}perv$. Stable beams for a long pulse duration of $5{\sim}10\;s$ were tested at low accelerating voltages.

• 대한전자공학회논문지SD
• /
• 제44권11호
• /
• pp.15-19
• /
• 2007

OTFTs (Organic Thin Film Transistors)의 구동에 있어, 게이트 절연막 표면과 채널의 계면상태가 소자의 전기적 특성에 큰 영향을 미치게 된다. OTS(Octadecyltrichlorosilane)등과 같은 습식 SAM(Self Assembly Monolayer)를 이용하거나, $O_2$ Plasma와 같은 건식 표면 처리등 여러 표면 처리법에 대한 연구가 진행되고 있다. 본 논문에서는 pentacene을 진공 증착하기 전에 게이트 절연막을 $O_2$ plasma와 Ar ion beam을 이용하여 건식법으로 전처리 한 후 표면 특성을 atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS)를 사용하여 비교 분석하였고, 각 조건으로 OTFT를 제작하여 전기적 특성을 확인하였다. Ar ion beam으로 표면처리 했을 때, $O_2$ plasma처리했을 때 보다 향상된 on/off ratio 전기적 특성을 얻을 수 있었다. 표면 세정을 위하여 $O_2$ plasma 처리시 $SiO_2$ 표면의 OH-기와 반응하여 oxide trap density가 높아지게 되고 이로 인하여 off current가 증가하는 문제가 발생한다. 불활성 가스인 Ar ion beam 처리를 할 경우 게이트 절연막의 세정 효과는 유지하면서, $O_2$ Plasma 처리했을 때 증가하게 되는 계면 trap을 억제할 수 있게 되어, mobility 특성은 동등 수준으로 유지하면서 off current를 현저하게 줄일 수 있게 되어, 결과적으로 높은 on/off ratio를 구현할 수 있다는 것을 확인하였다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권1호
• /
• pp.10-14
• /
• 2004

A large area electron beam generator has been developed for industrial applications, for example, waste water cleaning, flue gas treatment, and food pasteurization. The operational principle is based on the emission of secondary electrons from the cathode when ions in the plasma contact the cathode, which are accelerated toward the exit window by the gradient of the electric potential. Conventional electron beam generators require an electron beam scanning mechanism because a small area thermal electron emitter is used. The electron beam of the large area electron beam generator does not need to be scanned over target material because the beam area is considerable. We have fabricated a large area electron beam generator with peak energy of 200keV, and a beam diameter of 200mm. The electron beam current has been investigated as a function of accelerating voltage and distance from the extracting window while its radial distribution in front of the extracting window has been also measured.

• Steel and Composite Structures
• /
• 제37권3호
• /
• pp.307-321
• /
• 2020

The slim-floor solution provides an efficient alternative to the classic slab-over-beam configuration due to architectural and structural benefits. Two deficiencies can be identified in the current state-of-art: (i) the technique is limited to nonseismic applications and (ii) the lack of information on moment-resisting slim-floor beam-to-column joints. In the seismic design of framed structures, continuous beam-to-column joints are required for plastic hinges to form at the ends of the beams. The present paper proposes a slim-floor technical solution capable of expanding the current application of slim-floor joints to seismic-resistant composite construction. The proposed solution relies on a moment-resisting connection with a thick end-plate and large-diameter bolts, which are used to fulfill the required strength and stiffness characteristics of continuous connections, while maintaining a reduced height of the configuration. Considering the proposed novel solution and the variety of parameters that could affect the behavior of the joint, experimental and numerical validations are compulsory. Consequently, the current paper presents the experimental and numerical investigation of two slim-floor beam-to-column joint assemblies. The results are discussed in terms of moment-rotation curves, available rotational capacity and failure modes. The study focuses on developing reliable slim-floor beam joints that are applicable to steel building frame structures located in seismic regions.

• 폴리머
• /
• 제34권1호
• /
• pp.74-78
• /
• 2010

본 연구에서는 다양한 전류조건하에 전자선 조사로 가교된 리튬 이차전지용 폴리에틸렌 분리막을 제조하였다. 제조된 폴리에틸렌 분리막의 가교율은 조사량이 증가할수록 그리고 빔 전류가 낮을수록 증가하여 최대 71%까지 증가하였다. 낮은 빔 전류에서 조사된 폴리에틸렌 분리막은 상용 분리막 보다 우수한 열수축률(51%) 및 기계적 특성을 보여주었다. 가교된 분리막의 이온전도도는 $1.01{\times}10^{-3}\;S/cm$와 전해액 함침률(275%)은 조사되지 않은 분리막과 거의 동일하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.259-259
• /
• 2008

The LTCC (Low Temperature Co-fired Ceramic) technology meets the requirements for high quality microelectronic devices and microsystems application due to a very good electrical and mechanical properties, high reliability and stability as well as possibility of making integrated three dimensional microstructures. The wet process, which has been applied to the etching of the metallic thin film on the ceramic substrate, has multi process steps such as lithography and development and uses very toxic chemicals arising the environmental problems. The other side, Plasma technology like ion beam sputtering is clean process including surface cleaning and treatment, sputtering and etching of semiconductor devices, and environmental cleanup. In this study, metallic multilayer pattern was fabricated by the ion beam etching of Ti/Pd/Cu without the lithography. In the experiment, Alumina and LTCC were used as the substrate and Ti/Pd/Cu metallic multilayer was deposited by the DC-magnetron sputtering system. After the formation of Cu/Ni/Au multilayer pattern made by the photolithography and electroplating process, the Ti/Pd/Cu multilayer was dry-etched by using the low energy-high current ion-beam etching process. Because the electroplated Au layer was the masking barrier of the etching of Ti/Pd/Cu multilayer, the additional lithography was not necessary for the etching process. Xenon ion beam which having the high sputtering yield was irradiated and was used with various ion energy and current. The metallic pattern after the etching was optically examined and analyzed. The rate and phenomenon of the etching on each metallic layer were investigated with the diverse process condition such as ion-beam acceleration energy, current density, and etching time.

• 한국안전학회지
• /
• 제37권4호
• /
• pp.129-138
• /
• 2022

A new method for injecting cooling water into the Korean research reactor (KRR) in the event of beam tube rupture is proposed in this paper. Moreover, the research evaluates the risk to the reactor core in terms of core damage frequency (CDF). The proposed method maintains the cooling water in the chimney at a certain level in the tank to prevent nuclear fuel damage solely by gravitational coolant feeding from the emergency water supply system (EWSS). This technique does not require sump recirculation operations described in the current procedure for resolving beam tube accidents. The reduction in the risk to the core in the event of beam tube rupture that can be achieved by the proposed change in the cooling water injection design is quantified as follows. 1) The total CDF of the KRR for the proposed design change is approximately 4.17E-06/yr, which is 8.4% lower than the CDF of the current design (4.55E-06/yr). 2) The CDF for beam tube rupture is 7.10E-08/yr, which represents an 84.1% decrease compared with that of the current design (4.49E-07/yr). In addition to this quantitative reduction in risk, the modified cooling water injection design maintains a supply of pure coolant to the EWSS tank. This means that the reactor does not require decontamination after an accident. Thermal hydraulic analysis proves that the water level in the reactor pool does not cause damage to the nuclear fuel cladding after beam tube rupture. This is because the amount of water in the chimney can be regulated by the EWSS function. The EWSS supplies emergency water to the reactor core to compensate for the evaporation of coolant in the core, thus allowing water to cover the fuel assemblies in the reactor core over a sufficient amount of time.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2004년도 제26회 학술발표회 초록집
• /
• pp.141-141
• /
• 2004

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.727-730
• /
• 2007

Coil inductor has been used widely as an electromagnet, because of the high magnetic filed resulting from the voltage applied to the coil. In this study the coils were used in vibration suppression as an actuator. The control system consists of a coil attached in aluminum beam and a permanent magnet set at its bottom. This actuation method is easy to be incorporated into the system and allows significant forces to be applied without contacting with the structure. Three types of coils (cylindrical type, square type, Circular sheet type) were employed in vibration suppression of cantilever beam. The positive position feedback (PPF) controller was applied to the magnet-coil actuator to suppress the first mode of vibration. Experimental results showed that the cylindrical type and square type coil made good vibration suppression efficiency under PPF controller than their eddy current damper. However, there was minimal difference for the circular sheet type coil if compared with its eddy current damper.