• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.58-64
• /
• 2013

Several joining methods involving resistance welding, laser welding, ultrasonic welding and mechanical joining are currently applied in manufacturing lithium-ion batteries. Cu and Al alloys are used for tab and bus bar materials, and laser welding characteristics for these alloys were investigated with similar and dissimilar material combinations in this study. The base materials used were Al 1050 and oxygen-free Cu 1020P alloys, and a disk laser was used with a continuous wave mode. In bead-on-plate welding of both alloys, the joint strength was higher than the strength of O tempered base material. In overlap welding, the effect of welding parameters on the tensile shear strength and bead shape was evaluated. Tensile shear strength of overlap welded joint was affected by interfacial bead width and weld defect formation. The tensile-shear specimen was fractured at the heat affected zone by selecting proper laser welding parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.138-145
• /
• 1999

Surface hardening of AC4C aluminium alloy with TiC powders was obtained by plasma transferred are (PTA) method, Bead appearance, microstrucutre and wear behavior were characterized in relation to the torch current, powder feed rate and wear condition. The width and the depth of bead were mainly increased with increasing torch current. The comparison of wear behavior between AC4C alloy and PTA treated AC4C alloy showed the remarkable enhancement of wear resistance.

• Korean Journal of Materials Research
• /
• v.14 no.4
• /
• pp.300-306
• /
• 2004

A laser welding has been made between sintered tip of Fe-Co-W and low carbon steel shank for the diamond saw blade. The welding characteristics and formation of defect has been investigated carefully for the weld fusion zone in different welding condition. Full penetration has been observed for the whole range of heat input investigated in the present work. Bead width and under-fill have been increased with the increase of heat input. With increasing of heat input small cavities were decreased while large cavities were increased. The ratio of total cavity area to the entire weld bead area was not changed significantly with change of heat input. Most of cavities were found near the tip, and supposed to be formed from the pore in the tip.

• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.48-52
• /
• 2005

To estimate welding deformation for large steel structures, either experiment result with small specimen or analysis result of FEM with small numerical model is used. Consequently, it is important to decide the welding length of specimen and numerical model not to have an effect on welding deformation for accurate estimation of whole welding deformation. This study experimentally clarifies the effect of welding length on angular distortion due to welding by varying welding length of specimens, but fixing width and thickness of specimens on V-groove butt welding, fillet welding and bead on plate welding. As a resell the critical welding length on fillet welding and on bead on plate welding is over 500mm and on V-groove butt welding is over 1,000mm.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.269-274
• /
• 1999

Aluminum alloy has not only physical characteristic of very high activated high thermal conductivity and high thermal coefficient expansion but also special characteristic of great difference fusibility of hydrogen between liquid and solid phase. Because of these reasons, Aluminum welding is very different. Therefore, only MIG welding method should be applied instead of other welding methods. In this study, in order to select optimal welding conditions, it has been to investigate the effectiveness on the welding current, welding speed, flow rate of gas and welding voltage to occurrence of spatters, external shape of bead, state of penetration and width and hight of bead by using filer metal of A15356(dia. 1.21mm) on the base material of A16061.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.69-75
• /
• 2002

This study investigated the effect of the system parameters on penetration depth measurement using infrared temperature sensing system. The distance from focusing lens to detector was varied to diminish the error in measuring weld bead width. The effect of bead surface shape on measured surface temperature profile was evaluated using specimen heated by electric resistance. The measuring distance from laser beam was changed to optimize the measuring point. The results indicated that the monitoring device of surface temperature using infrared detector array was applicable to real time penetration depth control.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.62-68
• /
• 2002

This study investigated the feasibility of penetration depth measurement using infrared temperature sensing on the weld surface. The detection point was optimized by FEM analysis in the laser keyhole welding. The profile of the weld surface temperature was measured using infrared detector array. Surface temperature behind the weld pool is proportional or exponentially proportional to penetration depth and bead width. From the results, the monitoring device of surface temperature using infrared detector array was applicable fur real time penetration depth control.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.9-16
• /
• 2009

In this paper, the coaxial monitoring system to capture image of weld pool was developed in laser-arc hybrid welding. In order to obtain the reliable image, green laser was used as a illumination system and measuring components such as band pass filter, ND (Neutral Density) filter and shutter speed was designed and optimized. Using this monitoring system, weld pool images were captured according to laser power, welding speed, welding current and interspace between laser and arc through the experiment. ANOVA (Analysis of Variation) was carried out to identify the influence of process variables on bead widths extracted from captured images of monitoring system. Welding speed and current were major factor to affect weld pool.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.141-148
• /
• 2021

In this paper, we propose an algorithm of welding bead detection and evaluation using geodesic active contour algorithm and high pass filter with image processing technique. The algorithm uses histogram equalization and high pass filter as gaussian filter to improve contrast. The image processing techniques smoothens the welding beads reduce the noise on an image. Then, the algorithm detects the welding bead area by applying the geodesic active contour algorithm and morphological ooperation. It also applies the balloon force that either inflates in, or deflates out the evolving contour for a better segmentation. After that, we propose a method for determining the quality of welding bead using effective length and width of the detected bead. In the experiments, our algorithm achieved the highest recall, precision, F-measure and IOU as 0.9894, 0.9668, 0.9780, and 0.8957 respectively. We compared the proposed algorithm with the conventional algorithms to evaluate the performance of the proposed algorithm. The proposed algorithm achieved better performance compared to the conventional ones with a maximum computational time of 0.6 seconds for segmenting and evaluating one welding bead.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.365-372
• /
• 2004

The laser welding and its analysis were carried out using high power 6kW $CO_2$ laser for high strength steels such as DP, TRIP and conventional high strength steels. Bead on plate welding of thin sheet was examined to investigate the effect of weld variables of laser welding, and to obtain optimum welding condition. In order to investigate the formability of welded high strength steels, LDH test was added on this work. At high welding speed, the partial penetration was obtained by low heat input. Meanwhile, porosity was formed in the bead at low weld speed because of extremely higher heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. It was shown that the DP steels had lower porosity level and smooth bead shape, therefore better laser weldability than TRIP steels and conventional high strength steels. In addition, LDH test shows that the welded DP steels have about $90\%$ formability value of base metal, although TRIP steel and conventional high strength steels have about $80\%$ formability value of its base metal.