• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.298-300
• /
• 2015

Beacon is a signal device, which mainly used to support the safety of the locate and operation of a watercraft and aircraft. Recently, the IT sector BLE (Bluetooth Low Energy) also made possible to operate with less energy over several months using a beacon standards are applied. In addition, the location-based services and technologies using BLE Beacon has attracted attention. However, there is the problem that by using only the position location Beacon devices when high error rate can be measured accurate position. Therefore, in this paper, combines WiFi and Beacon based on Smartphone. Also propose an indoor positioning algorithm reduces the error rate of the position location value.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1388-1391
• /
• 1996

This paper presents the structure and functions of the differential beacon receiver for receiving DGPS error correction data. The differential beacon receiver is designed using commercially available components. Its functions are being implemented and tested in laboratory. Filed test is scheduled for the end of this year.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1017-1021
• /
• 2020

In the V2X communications, each vehicle periodically broadcasts a message, called a beacon, so that its neighbor vehicles can accurately predict the near-future positions of the sending vehicle. In particular, the mobility-adaptive beacon broadcast (MAB2) scheme keeps the tracking error of a sending vehicle below a fixed threshold within a few consecutive beacon losses. In this paper, we present a random-early beacon broadcast (REB2) scheme that addresses the beacon aging problem of the MAB2 scheme. The simulation results show that, for a neighbor vehicle within 100 m distance, the tracking failure probability of REB2 scheme can be reduced to less than 1/10 of that of MAB2 scheme.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1155-1160
• /
• 2007

This paper presents position error for the robot localization system using the ultrasonic wave. The distance between the receiver and a beacon can be computed by using the difference between times of flight. The distance information measured by ultrasonic wave has errors. The position is calculated by distances, and this error is caused by distance errors. The position error is different from receiver¡s position. And the position is also calculated by beacon location. This paper calculates worst case position error within measuring area, and finds beacons location to reduce the position error.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.7
• /
• pp.734-741
• /
• 2009

A new localization algorithm is proposed for a fast moving mobile robot, which utilizes only one beacon and the global features of the differential-driving mobile robot. It takes a relatively long time to localize a mobile robot with active beacon sensors since the distance to the beacon is measured by the traveling time of the ultrasonic signal. When the mobile robot is moving slowly the measurement time does not yield a high error. At a higher mobile robot speed, however, the localization error becomes too large to locate the mobile robot. Therefore, in high-speed mobile robot operations, instead of using two or more active beacons for localization, only one active beacon and the global features of the mobile robot are used to localize the mobile robot in this research. The two global features are the radius and center of the rotational motion for the differential-driving mobile robot which generally describe motion of the mobile robot and are used for the trace prediction of the mobile robot. In high speed operations the localizer finds an intersection point of this predicted trace and a circle which is centered at the beacon and has the radius of the distance between the mobile robot and the beacon. This new approach resolves the large localization error caused by the high speed of the mobile robot. The performance of the new localization algorithm has been verified through the experiments with a high-speed mobile robot.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1182-1188
• /
• 2010

This paper proposes a precise localization algorithm for a quickly moving mobile robot. In order to localize a mobile robot with active beacon sensors, a relatively long time is needed, since the distance to the beacon is measured using the flight time of the ultrasonic signal. The measurement time does not cause a high error rate when the mobile robot moves slowly. However, with an increase of the mobile robot's speed, the localization error becomes too high to use for accurate mobile robot navigation. Therefore, in this research into high speed mobile robot operations, instead of using two active beacons for localization an active beacon and dual compass are utilized to localize the mobile robot. This new approach resolves the high localization error caused by the speed of the mobile robot. The performance of the precise localization algorithm was verified by comparing it to the conventional method through real-world experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.7
• /
• pp.1307-1312
• /
• 2015

The recent adoption of Bluetooth LE technology in smart phones triggered commercial interest in RSSI-based positioning technology. Estimation error in RSSI measurement due to the antenna pattern, multipath fading, environmental noise has to be considered for designing beacon systems. The paper proposes an analysis method and beacon planning rules for a small and isolated indoor service area, based on probabilistic model of RSSI estimation error. As an practically important guide, the beacons have to be installed at the boundary of the service area to minimize the maximum position error, whereas the beacons have to be evenly distributed in the service space to minimize the average estimation error.

• Journal of Satellite, Information and Communications
• /
• v.11 no.4
• /
• pp.63-67
• /
• 2016

Recently, BLE beacons are widely used in indoor precision positioning systems because of their low battery consumption and low infrastructure cost. However, existing BLE beacon based indoor positioning algorithms are difficult to compensate for position errors due to the user's moving speed. Therefore, we proposed a position error correction algorithm that combines bounced cancellation and minimum distance maintenance algorithm with a positioning error correction method using direction vectors. Experimental results show that the proposed algorithm guarantees superior positioning performance than the existing indoor positioning algorithm and also improves the performance of position error compensation.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.5
• /
• pp.195-200
• /
• 2021

In this paper, we propose a method for a mobile robot to estimate a specific location of a service provision target using a beacon-tag for the purpose of providing location-based services (LBS) to users in an indoor environment. To estimate the location, the irregular characteristics and error factors of the received signal strength indicator (RSSI) generated from the beacon are analyzed, and the distance conversion function is derived from the RSSI data extracted by applying a Gaussian filter. Then, the distance data converted from the plurality of beacons estimates an indoor location through a triangulation technique. After that, the improvement in the location estimation is analyzed by applying the temporal confidence reasoning technique. The possibility of providing a LBS of a mobile robot was confirmed through a location estimation experiment for a plurality of designated locations in an indoor environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.9A
• /
• pp.852-858
• /
• 2010

In this paper, the compensation algorithm for radiodetermination error using a concept of determination coordinator value of equivalent distance rate (CADE) is proposed, and the performance of the proposed algorithm is analyzed. As a result of the experiments, CADE improves the performance of the algorithm accuracy about 37.5% and 69.8% each in the inside and outside of 4 beacon nodes. Furthermore, the CADE is 76.3% excellent enough to compensate 2m or more of the radiodetermination error. It also confirms that CADE can be adapted to the wide range by installing only 4 beacon nodes according to the excellence of compensation performance besides the ranges of 4 beacon nodes. From the results, it is strongly considered that the proposed algorithm CADE can be used to the performance enhancement of radiodetermination systems using SDS-TWR.