• Economic and Environmental Geology
• /
• v.37 no.6 s.169
• /
• pp.603-612
• /
• 2004

Pyrochlore is known as one of the most promising materials for the immobilization of radionuclide in high level waste. This study included the synthesis, phase relation and characteristics of $pyrochlore(CaCeZr_xTi_{2-x}O_{7,\;x=0.2\~2.0)$ in the system of Ca-Ce-Zr-Ti-O. Using the CPS(Cold pressing and sintering) method, the mixtures of $CaCO3_,\;CeO_2,\;ZrO_2\;and\;TiO_2$ oxides were pressed, and sintered at $1100\~1600^{\circ}C$ for 20 hours. The optimal synthetic conditions at various compositions were differed from 1300 to $1600^{\circ}C$ Even in the optimal temperatures, pyrochlore or fluorite coexisted with minor amount of perovskite, $CeO_2\;or\;Ce_{0.75}Zr_{0.25}O_2$. It was confirmed that pyrochlore and fluorite structures were stable at $x\leq0.6\;and\;x\geq1.0$, respectively. Especially, the compositions of pyrochlore or fluorite showed non-stoichiometric compositions in that contents of Ca and Ti were more deficient and those of Zr and Ce were more excess than batch compositions with the increase of x value. These characteristics stemmed from the behavior of elements occupied at eight- and six-coordinated site, and then caused the coexistence of perovskite, $CeO_2\;or\;Ce_{0.75}Zr_{0.25}O_2$ along with pyrochlore or fluorite.

• Applied Chemistry for Engineering
• /
• v.2 no.3
• /
• pp.270-278
• /
• 1991

Carboxymethyl chitin(CM-chitin) was prepared by the reaction of alkali chitin with monochloroacetic acid in isopropyl alcohol. According to the pH variation, the adsorptivity of this chelating polymer to the alkali-earth metal ions such as $Ca^{2+},\;Mg^{2+}$, $Sr^{2+}$, $Ba^{2+}$ ions was determined by batch method. The adsorption tendency of this chelating polymer to most metal ions was increased with the increase of pH. The highest degree of adsorption was observed toward $Ca^{2+}$ ion among the alkali-earth metal ions. The selectivity adsorption property toward $Ca^{2+}$ ion was examined in the solution of $Ca^{2+}$ and $Mg^{2+}$ ions, and it was observed that CM-chitin showed excellent selectivity to $Ca^{2+}$ ion than $Mg^{2+}$ ion. $Mg^{2+}$ ion bound to CM-chitin molecule in the presence of $Ca^{2+}$ ion owing to low equilibrium constant. In the adsorption experiment of $Ca^{2+}$ and $Mg^{2+}$ ions to the CM-chitin under coexistence of $Na^+$ and $K^+$ ions, it observed that adsorptivity of only $Ca^{2+}$ ions was not affected by these monovalent cations.

• Analytical Science and Technology
• /
• v.7 no.1
• /
• pp.103-114
• /
• 1994

The elution behaviors of Ni(II), Cu(II), Co(II), and Cr(II) in 1-phenyl-3-methyl-4(2-hydroxy-5-X-phenylazo)-5-pyrazolone, [Pm(2-OH)(5-X)PaPz](X=H, $CH_3$, $NO_2$, Cl) chelates have been studied by reversed phase HPLC. Thirteen metal-[Pm(2-OH)(5-X)PaPz] chelates were prepared and characterized by UV, IR, MS, and ICP spectroscopic methods. These metal-2-hydroxyarylazopyrazolone chelates were successfully separated on Novapak-$C_{18}$ column using methanol/water mixtures as a mobile phases. It was found that the chelates were eluted properly in an acceptable range of the capacity factor value($0{\leq}log\;k^{\prime}{\leq}1$). The dependence of the capacity factor(log k') on the volume fraction of water in the binary mobile phase showed a good linearity. Also, there was a good linear dependence of the capacity factor on the liquid-liquid extraction distribution ratio($D_c$) in methanol-water/n-pentadecane extraction system by the batch method. It suggested that the retention of the chelates in the reverse phase liquid chromatographic system be largely due to the solvophobic effect.

• Korean Journal of Soil Science and Fertilizer
• /
• v.51 no.1
• /
• pp.35-49
• /
• 2018

This study was initiated to quantitatively evaluate the effects of five heavy metals (Cd, Cu, Zn, Pb, and Ni) on growth and P removal efficiencies of Pseudomonastaeanensis, known as the phosphorus accumulating microorganism. The heavy metals were added individually and with the binary mixture to the batch culturing system of Pseudomonastaeanensis. $IC_{50}$ and $EC_{50}$ were used to quantitatively evaluate their effects on the growth and phosphorus removal efficiency of Pseudomonas taeanensis in those treatments. Additionally, additive index value method was used to evaluate the interactive effects of heavy metals for Pseudomonas taeanensis in this study. As those heavy metals were singly added to Pseudomonastaeanensis, the greatest inhibitory effect on its growth and P removal efficiency was observed in Cd, whereas, the smallest effect was found in Ni. As the concentrations of all heavy metals added were gradually increased, its growth and P removal efficiency was correspondingly decreased. Specifically, $IC_{50}$ of Pseudomonas taeanensis for Cd, Cu, Zn, Pb, and Ni were $0.44mg\;L^{-1}$, $5.12mg\;L^{-1}$, $7.46mg\;L^{-1}$, $8.37mg\;L^{-1}$ and $14.56mg\;L^{-1}$, respectively. The P removal efficiency of Pseudomonas taeanensis was 81.1%. $EC_{50}$ values of Pseudomonas taeanensis for Cd, Cu, Zn, Pb, and Ni were $0.44mg\;L^{-1}$, $4.08mg\;L^{-1}$, $7.17mg\;L^{-1}$, $8.90mg\;L^{-1}$ and $11.26mg\;L^{-1}$, respectively. In the binary treatments of heavy metals, the lowest $IC_{50}$ and $EC_{50}$ were found in the Cd + Cu treatment, whereas, the highest $IC_{50}$ and $EC_{50}$ were found in the Zn + Pb and Pb + Ni treatments, respectively. Most of the interactive effects for the binary mixture treatments of heavy metals were antagonistic. Based on the results obtained from this study, it appears that they could provide the basic information about the toxic effects of the respective individual and binary treatments of heavy metals on the growth and P removal efficiency of other phosphorus accumulating organisms.

• Journal of KIISE:Databases
• /
• v.33 no.3
• /
• pp.310-326
• /
• 2006

In this paper, we deal with a method of efficiently processing continuous queries in a data stream environment. We classify previous query processing methods into two dual categories - data-initiative and query-initiative - depending on whether query processing is initiated by selecting a data element or a query. This classification stems from the fact that data and queries have been treated asymmetrically. For processing continuous queries, only data-initiative methods have traditionally been employed, and thus, the performance gain that could be obtained by query-initiative methods has been overlooked. To solve this problem, we focus on an observation that data and queries can be treated symmetrically. In this paper, we propose the duality model of data and queries and, based on this model, present a new viewpoint of transforming the continuous query processing problem to a multi-dimensional spatial join problem. We also present a continuous query processing algorithm based on spatial join, named Spatial Join CQ. Spatial Join CQ processes continuous queries by finding the pairs of overlapping regions from a set of data elements and a set of queries defined as regions in the multi-dimensional space. The algorithm achieves the effects of both of the two dual methods by using the spatial join, which is a symmetric operation. Experimental results show that the proposed algorithm outperforms earlier methods by up to 36 times for simple selection continuous queries and by up to 7 times for sliding window join continuous queries.

• Journal of Animal Science and Technology
• /
• v.45 no.4
• /
• pp.641-648
• /
• 2003

In a batch mode treatment process, which electrolyzes the wastewater after derivation of N-P crystal formation and recovery, the characteristics of pollutant removal induced with the changes of loading rate and hydraulic retention time were studied. $MgCl_2$ was used as Mg source for the formation of struvite and the molar ratio of $MgCl_2$ to $PO_4^{3-}$ in influent was 1.3. When analyzing the average treatment efficiencies and removal characteristics obtained from four separate operations (Run I, II, III, IV), removal efficiencies of PO43- was not function of its loading rate. Under a condition of sufficient aeration and Mg source provided, over 88% of $PO_4^{3-}$ was eliminated by the formation of MAP without any pH adjustment, in spite of loading rate variation. An optimum-loading rate of NH4-N to achieve high removal efficiency was approximately $100g/m^3/d$. Below that loading rate, the removal of NH4-N was proportional to the loading rate into the system, and hence stable and high removal efficiency, over 90%, was achieved. However, when the loading rate increased over that rate, removal efficiency began to drop and fluctuate. Removal efficiency of TOCs was dependant upon the hydraulic retention time ($r^2$=0.97), not upon the loading rate. Stable and high color removal (94%) was obtained with 2 days of HRT in electrolysis reactor.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.6
• /
• pp.547-554
• /
• 2010

In this study, new manganese oxide (i.e., black-birnessite) particles with nanostructures were prepared and its physico-chemical properties and oxidative-transformation efficiency on 1,4-naphthoquinine(1,4-NPQ) in the presence of reactive mediator was investigated. The results were also compared with that of the manganese oxide (i.e., brown-birnessite) particles synthesized by classical McKenzie method. Analysis of XRD and SEM data show that the particles are a single phase corresponding to a birnessite-based manganese oxide with cotton ball-like shapes containing nanofibers. In batch experiments, removals of 1,4-NPQ by the black-birnessite follows pseudo-first-order kinetics and the rate constant values obtained are greater about 2.3 times than that of the brown-birnessite in spite of its lower surface area (41.0 vs 19.80 $m^2/g$). The results can be explained by the higher crystallinity and nano structured features of the back-birnessite particles, which give higher reactivity for the removals of the quinone compound. HPLC analysis of the reaction products confirmed that the balck-birnessites removed 1,4-NPQ through cross-coupling reaction in the presence of catechol as a reactive mediator.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.11
• /
• pp.649-655
• /
• 2015

As a novel water treatment membrane, concept of ceramic-based graphene membrane (CbGM) was suggested, and its mass transport behavior was investigated. The selectivity of CbGM was given by graphene material which is consisting of active layer, only transmitting water, but rejecting salts. Filtration-assisted assembly methods was employed as a facile method to fabricate CbGM. Surface morphology and characteristics of CbGM were analyzed by scanning electron microscopy (SEM) and contact angle. In addition, three different kinds of solutes (i.e., NaCl, $MgCl_2$, $Na_2SO_4$) were tested in batch forward osmosis system to confirm the mass transport behavior. Through surface morphology analysis and mass transport behavior, it was revealed that interlocking between graphene layers is very important, rather than thickness of laminated graphene layers, in terms of selectivity to CbGM. All the anions in each solute showed faster transport than those of cations. In addition, solutes which have high ion valence charge ratio of anion to cation ($Z^-/Z^+$) was easier to be passed through CbGM. It indirectly implied that the surface charge of CbGM appear to be positive. In addition, It showed that surface charge of CbGM has a great role on mass transport, in particular, transport of matter having charges, generally ions.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.4
• /
• pp.1088-1095
• /
• 2019

The CKD extract is wastewater from which KCl in CKD has been removed to reuse CKD as a cement raw material, and tried to reuse no extracts due to problems such as wastewater treatment facility expansion. As a result of removing KCl by the ion exchange method, the pH of the extract after ion exchange decreased from 12.7 to less than pH 2, and it was confirmed that H⁺ of the cation exchange resin was dissolved in the extract through ion exchange. In addition, the selectivity of the ion exchange was removed in the order of Ca²⁺, K⁺, it was determined that the increase in the contact time to remove the K⁺ ions. The batch system had a contact time of 6 times or more, compared to the continuous system, and showed 4 times of K⁺ removal efficiency and 7 times of Cl^- removal efficiency. It was showed by analyzing the pH of the extract that more H⁺ of the cation exchange resin was extracted than OH^- of anion exchange resin as the pH of the extract was changed.

• Journal of Ginseng Research
• /
• v.37 no.1
• /
• pp.124-134
• /
• 2013

The authentication of the physico-chemical properties of ginsenosides reference materials as well as qualitative and quantitative batch analytical data based on validated analytical procedures is a prerequisite for certifying good manufacturing practice (GMP). Ginsenoside Rb1 and Rg1, representing protopanaxadiol and protopanaxatriol ginsenosides, respectively, are accepted as marker substances in quality control standards worldwide. However, the current analytical methods for these two compounds recommended by Korean, Chinese, European, and Japanese pharmacopoeia do not apply to red ginseng preparations, particularly the extract, because of the relatively low content of the two agents in red ginseng compared to white ginseng. In manufacturing fresh ginseng into red ginseng products, ginseng roots are exposed to a high temperature for many hours, and the naturally occurring ginsenoside Rb1 and Rg1 are converted to artifact ginsenosides such as Rg3, Rg5, Rh1, and Rh2 during the heating process. The analysis of ginsenosides in commercially available ginseng products in Korea led us to propose the inclusion of the (20S)- and (20R)-ginsenoside Rg3, including ginsenoside Rb1 and Rg1, as additional reference materials for ginseng preparations. (20S)- and (20R)-ginsenoside Rg3 were isolated by Diaion HP-20 adsorption chromatography, silica gel flash chromatography, recrystallization, and preparative HPLC. HPLC fractions corresponding to those two ginsenosides were recrystallized in appropriate solvents for the analysis of physico-chemical properties. Documentation of those isolated ginsenosides was achieved according to the method proposed by Gaedcke and Steinhoff. The ginsenosides were subjected to analyses of their general characteristics, identification, purity, content quantification, and mass balance tests. The isolated ginsenosides showed 100% purity when determined by the three HPLC systems. Also, the water content was found to be 0.534% for (20S)-Rg3 and 0.920% for (20R)-Rg3, meaning that the net mass balances for (20S)-Rg3 and (20R)-Rg3 were 99.466% and 99.080%, respectively. From these results, we could assess and propose a full spectrum of physico-chemical properties of (20S)- and (20R)-ginsenoside Rg3 as standard reference materials for GMP-based quality control.