• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.69-77
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties were decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the In atmospheric gas($H_2$ : 75%, $N_2$ : 25%) and the HNx atmospheric gas($H_2$ : 5%, $N_2$ : 95%) We confirmed the following characteristics, mechanical properties were changed under the influence of the annealing cycle and the atmospheric gas. And, we have some result according to heat treatment method. Elongation of the mechanical properties in the HNx BAF is higher than the Ax BAF. But tensile strength and hardness is higher than the HNx BAF.

• Membrane Journal
• /
• v.12 no.4
• /
• pp.226-239
• /
• 2002

A process simulation model of pervaporation process has been developed as a design tool to analyse and optimize the dehyhration of organic solvents through a commercial scale of pervaporative plate-and-frame modules that contain a stack of membrane sheets. In the simulation model, the mass balance, the heat balance and the concentration balance are integrated in a finite elements-in-succession method to simulate the overall process. In the integration method, a feed channel between membrane sheets in the modules was taken as differential unit element volume to simplify calculation procedure and shorten computing time. Some of permeation parameters used in the simulation model, were quantified directly from the dehydration experiment of ethanol through $AzeoSep^{TM}$-2002 membrane which is a commercial pervaporation membrane. The simulation model was verified by comparing the simulated values with experimental data. Using the model, continuous and batch pervaporation processes were simulated, respectively, to acquire basic data for analysing and optimizing in the dehydration of ethanol through the membrane. Based on the simulation results, a comparison between the continuous and the batch pervaporation processes would be discussed.

• Journal of Intelligence and Information Systems
• /
• v.11 no.1
• /
• pp.169-189
• /
• 2005

In order to derive a better classifier with a limited number of training examples, active teaming alternately repeats the querying stage fur category labeling and the subsequent learning stage fur rebuilding the calssifier with the newly expanded training set. To relieve the user from the burden of labeling, especially in an on-line environment, it is important to minimize the number of querying steps as well as the total number of query examples. We can derive a good classifier in a small number of querying steps by using only a small number of examples if we can select multiple of diverse, representative, and ambiguous examples to present to the user at each querying step. In this paper, we propose a cluster-based batch query selection method which can select diverse, representative, and highly ambiguous examples for efficient active learning. Experiments with various text data sets have shown that our method can derive a better classifier than other methods which only take into account the ambiguity as the criterion to select multiple query examples.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.6
• /
• pp.609-614
• /
• 2010

In the present study, bioethanol was produced using batch style reactor from food wastes which has organic characteristics. Pretreatment was required to reduce its particle size and produce fermentable sugar. Two different enzymes such as carbohydrase and gulcoamylase were tested for saccharification of food waste. The efficiency of carbohydrase saccharification (0.63 g/g-TS) has shown higher than glucoamylase saccharification(0.42 g/g-TS). Saccharomyces cerevisiae produced bioethanol via separate hydrolysis & fermentation (SHF) method and simultaneous saccharification fermentation (SSF) method. The production amount of bioethanol was 0.27 g/$L{\cdot}hr$ for SHF and 0.44 g/$L{\cdot}hr$ for SSF.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.108-117
• /
• 2012

This paper focuses on a performance analysis of TRN among various nonlinear filtering methods. In a TRN research, extended Kalman filter(EKF) is a basic estimation algorithm. In this paper, iterated EKF(IEKF), EKF with stochastic linearization(SL), and unscented Kalman filter(UKF) algorithms are introduced to compare navigation performance with original EKF. In addition to introduced sequential filters, bank of Kalman filters method, which is one of the batch method, is also presented. Finally, by simulating an artificial aircraft mission, EKF with SL was chosen as the most consistent filter in the introduced sequential filters. Also, results suggested that the bank of Kalman filters can be alternative for TRN, when a fast convergence of navigation solution is needed.

• Archives of Pharmacal Research
• /
• v.21 no.5
• /
• pp.570-575
• /
• 1998

To develop a cotton derivatives with prolonged antimicrobial activities, homosulfamine (Hs) was coupled to cotton xanthate (CX) via chelate bond in the presence of Cu(II) ion by one- and two-bath processes. In one-bath process, CX was treated with Cu(II)-Hs solution. In two-bath process, CX was treated with Cu(II) ion solution to produce CX-Cu(II) complex, which was isolated and treated in turn with Hs solution. Effects of concentration, Cu(II)/Hs ratio, and pH on the binding of Hs were investigated at $10{\circ}C$ . In one-bath process, binding of hs took place readily with optimum pH around 5-6. the amount of binding increased to give a maximum within 5 min and decreased slowly to establish an equilibrium withhin an hour. In two-bath process, binding of Hs was much lower than that of one-bath process. Release of Hs from CX-Cu(II)-Hs was investigated by batch and flow method. antimicrobial activiteis of CX-Cu(II)-Hs was investigated by batch and flow method. Antimicrobial activities of CX-Cu(II)-Hs were tested against Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa and Escherichia coli and it showed prolonged activity compared to that of free Hs.

• Textile Coloration and Finishing
• /
• v.21 no.1
• /
• pp.1-9
• /
• 2009

A lot of research has been made over the recent decade to develop testing packages with antimicrobial properties to improve food safety. In this study, a new method, experimental device and technology for environmental corresponding packages of polypropylene (PP) film has been developed to provide effective temperature buffering during the transport/long-term storage of grains or foodstuffs from the supplier to the market. This quantitatively optimized mixing system enabled to produce PP films with the 700$\sim$1,400d (width;1.5$\sim$3mm, thickness;0.01$\sim$0.5mm). In the whole mixing systems, the finely-granulated inorganic illite and PP virgin chip for master batch (M/B) chip was calculated by digital measurement methods, and then the M/B chip for PP film was adapted through a air jet and PP grinding method. The prepared PP film was characterized with tensile strength and elongation, far infrared radiation (FIR) emissivity, antimicrobial activity and deodorization properties. The results revealed that the two differently grain-sized illite could be show homogeneously dispersed on PP chip surface, and as the increasing of illite content, the FIR emissivity and the anion emission rate of film was increasingly improved. In both of 325 and 1,500 mesh-sized illite contained PP chip, of course the antimicrobial activity was good. But the ultimate deodorization rate for ammonia gas of PP film were found to be approximately the same.

• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.177-186
• /
• 2015

This study aims to suggest the direction in which furniture design can contribute, keeping with the trend of small quantity batch production by analyzing cases of furniture design manufacturing. This study analyzed cases of furnitures and lights made by 3D printing with 3 classifications. They are 1st, classification by correlation between 3D printing method and materials, 2nd, classification by 8 formative characteristics of 3D printing furniture design, 3rd, comparison analysis of competitiveness between existing furniture design and 3D printing furniture design by practicality, usability and durability. The competitiveness 3D printing technique arouses in furniture design industry, which is investigated in this thesis, is as follows. 1st, small quantity batch production, which caters to personal taste, is made possible. 2nd, transmission and transportation via digital are became more convenient. 3rd, it brings about a breakthrough in furniture design manufacturing. 4th, there is room for development into the 'smart furniture design' industry through collaborative use of 3D printing and internet of things. 5th, an Eco-friendly method of furniture design is consistently facilitated.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2018

Recently, the convolutional neural network shows high performance in many computer vision tasks. However, convolutional neural networks require enormous amount of operation, so it is difficult to adopt them in the embedded environments. To solve this problem, many studies are performed on the ASIC or FPGA implementation, where an efficient representation method is required. The fixed-point representation is adequate for the ASIC or FPGA implementation but causes a performance degradation. This paper proposes a separate optimization of representations for the convolutional layers and the batch normalization layers. With the proposed method, the required bit width for the convolutional layers is reduced from 16 bits to 10 bits for the ResNet-50 neural network. Since the computation amount of the convolutional layers occupies the most of the entire computation, the bit width reduction in the convolutional layers enables the efficient implementation of the convolutional neural networks.

• KSBB Journal
• /
• v.10 no.4
• /
• pp.401-405
• /
• 1995

An open pond type photobioreactor for mass cultivation of S. platensis was designed and the growth parameters from different cultivation processes were compared. 0.30(1/day) of specific growth rate and 1.69(g/$\ell$) of maximum cell density were obtained from batch cultivation. In fed-batch cultivation, specific growth rate and maximum cell density were estimated as 0.22(1/day) and 1.75(g/$\ell$), respectively. Maximum biomass productively from continuous cultivation was obtained as 0.44 (g/$\ell$/day). It proves that an outdoors-mass cultivation of S. platensis considering optimal environmental condition is economically feasible. In addition, the biomass productivity was studied in two different mixing systems such as agitation and air sparging methods. The biomass productivity by an agitation method was better than that in an air sparging method.