• Clean Technology
• /
• v.9 no.4
• /
• pp.179-187
• /
• 2003

The technology of fluidized bed to use dry sorbent can be new technology that reduce the operating cost and make efficient operation. Therefore, this study investigated $CO_2$ control by dry sorbents with operating variables in a fluidized bed, compared with fixed bed for $CO_2$ adsorption capacity and pressure drop, and presented the $CO_2$ adsorption capacity of activated carbon, molecular sieve 5A, molecular sieve 13X, and activated alumina. As the results of this study, the basic data could be achieved for operation of fluidized bed process, and fluidized bed process presented relatively high $CO_2$ adsorption capacity and low pressure drop with the increase of gas velocity. In addition, molecular sieve 5A showed 1.1~3.0-fold later breakthrough point and 1.1~2.7-fold higher adsorption capacity than the other dry sorbents.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.2
• /
• pp.136-141
• /
• 2005

Li-doped NiO was synthesized by molten salt method. $LiNO_3$-LiOH flux was used as a source for Li doping. $NiCl_2$ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5:1 to 30:1 during the synthetic procedure and the Li doping amount of synthesized materials were found between 0.086-0.190 as a Li ion to Ni ion ratio. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies, however the lattice parameter decreased from 0.41769nm in pure NiO to 0.41271nm as Li doping amount increased. Hydrogen gas sensors were fabricated using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs $H_2$ concentration was checked up to 4% of $H_2$ in air (as higher concentrations above 4.65% are explosive in air) using Li doped NiO of Li ion/Ni ion=0.111 as the sensor material. The response time T90 and the recovery time RT90 were less than 25 sec. There was minimum interference of other gases and hence $H_2$ gas can easily be detected.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.79-79
• /
• 2008

We report the growth of $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thin films and their substrate-dependent electrical characteristics. BST thin films were deposited on alumina(non-single crystal), $Al_2O_3$(100) substrates by Nd:YAG Pulsed Laser Deposition(PLD) with a 355nm wavelength at substrate temperature of $700^{\circ}C$ and post-deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for 1hours. BST materials had been chosen due to high dielectric permittivity and tunability for high frequency applications, To analyze the oxygen partial pressure effects, deposited films at 1, 10, 50, 100, 150, 200, 300 mTorr. The effects of oxygen pressure on structural properties of the deposited films have been investigated by X-ray diffraction(XRD) and atomic force microscope(AFM), respectively. Then we manufactured a inter-digital capacitor(IDC) patterns twenty fingers and $10{\mu}m$ gap, $700{\mu}m$ length and electrical properties were characterized. The results provide a basis for understanding the growth mechanisms and basic structural and electrical properties of BST thin films as required for tunable microwave devices applications such as varactors and tunable filters.

• Applied Chemistry for Engineering
• /
• v.18 no.2
• /
• pp.142-147
• /
• 2007

In this study, mesoporous tin oxide was synthesized by sol-gel method using $C_{16}TMABr$ surfactant as a template in a basic condition. The optimum conditions for the synthesis of mesoporous $SnO_2$ were investigated and the obtained samples were characterized by XRD, nitrogen adsorption and TEM analysis. A mesoporous and nanostructured $SnO_2$ gas sensor with Au electrode and Pt heater has been fabricated on alumina substrate as one unit via a screen printing process. Sensing abilities of fabricated sensors were examined for CO and $CH_4$ gases, respectively, at $350^{\circ}C$ in the concentration range of 1~10,000 ppm. Influence of loading amount of palladium impregnated on $SnO_2$ was also tested in detection of those gases. High sensitivity to detecting gases and the fast response speed with stability were obtained with the mesoporous tin oxide sensor as compared to a non-porous one under the same detection conditions.

• Journal of Soil and Groundwater Environment
• /
• v.7 no.4
• /
• pp.48-58
• /
• 2002

As a pilot experiment for developing the monitoring system for oil spill from storage tank, previous approach of monitoring contaminated oil from mixed soil sample had the limitation that it cannot reflect the real situations of the contamination. In this study, more realistic contamination condition and water contents were considered. Fluorescence intensity was not affected by water contents. To acquire the stability of media, sand, Ca-bentonite, alumina, Fe-oxide, bead and silica were tested. Only sand was suitable to our system. These results should provide basic information for constructing reliable monitoring system.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.665-670
• /
• 2003

This study investigated the thermodynamic and the thermal decomposition properties of high concentration nitrate salts waste water for the lagoon sludge treatment. The thermodynamic property was carried out by COACH and GEMINI II based on the composition of nitrate Salts waste water. The thermal decomposition property was carried out by TG-DTA and XRD. Ammonium nitrate and sodium nitrate were decomposed at $250^{\circ}C$$730^{\circ}C$$450^{\circ}C$$Na_2O$ into stable $Na_2O$.$Al_2O_3$. The flow sheet for nitrate salts waste water treatment was proposed based on the these properties data. These will be used by the basic data of the process simulation.

• Journal of the Korean Chemical Society
• /
• v.21 no.1
• /
• pp.53-59
• /
• 1977

A method of synthesizing $NaAlCO_3(OH)_2$ (Dawsonite) and $KAlCO_3(OH)_2$, was investigated by blowing $CO_2$ gas into sodium and potassium aluminate solutions. The reactions were accomplished at a temperature of 80 to $90^{\circ}C$, while $CO_2$ gas was blowing into the solutions which the molar ratios of $Na_2O/Al_2O_3,\;and\;K_2O/Al_2O_3$ were 6 to 8 and 8 to 10, respectively. It was observed that highly purified Dawsonite and $KAlCO_3(OH)_2$ are produced when Alumina is present in Boehmite at an equilibrium solid phase with a large amount of $HCO_3^-$ in the solutions. The rational formulas of Dawsonite and $KAlCO_3(OH)_2$synthesized under the conditions should be expressed as $NaAlO(OH)HCO_3\;and\;KAlO(OH)HCO_3$, respectively, by IR analysis. In addition, electron microscopic observation also indicated that Dawsonite in a fibrous crystal and $KAlCO_3(OH)_2$ in a needleshaped crystal.

• The Journal of Natural Sciences
• /
• v.6 no.1
• /
• pp.103-108
• /
• 1993

Zeolites were discovered as a natural mineral more than two hundred ago. In the beginning, the mineral was used as ion-exchange material and adsorbent. After the end of World War II , however, a variety of zeolites have become available in large amounts because of the establishment of low temperature synthesis and the discobery of natural zeolite deposits of sedimentary origin. Various uses of xeolite were developed utilizing the unique crystal strucrure and function of these minerals. In connection with this development remakable progress has also been made in basic stuides on the related geology and mineralogy, crystallization from sols and gels, structure, ion exchange, adsorption and cataiysis. As a result, zeolites, which had been known only as mineral specimens displayed in museums. established a firm position among the high-technology masterials with excellent functional capabilities.

• Journal of the Korean Ceramic Society
• /
• v.47 no.5
• /
• pp.381-386
• /
• 2010

Some basic properties of inorganic coatings hardened by the room temperature reaction with alkalies were examined. The coating paste was prepared from the powders in the system $Al_2O_3-SiO_2$-CaO using blast furnace slag, fly ash and amorphous ceramic fiber after mixing with a solution of sodium hydroxide and water glass. The mineralogical and morphological examinations were performed for the coatings prepared at room temperature and after heating to $1200^{\circ}C$ respectively. The binding force of the coating hardened at room temperature was caused by the formation of fairly dense matrix mainly composed of oyelite-containing amorphous phase formed by the reaction between blast furnace slag and alkali solution. At the temperature, fly ash and ceramic fiber was not reacted but imbedded in the binding phase, giving the fluidity to the paste and reinforcing the coating respectively. During heating up to $1200^{\circ}C$, instead of a break in the coating, anorthite and gehlenite was crystallized out by the reaction among the binding phase and unreacted components in ternary system. The crystallization of these minerals revealed to be a reason that the coating maintains dense morphology after heating. The maintenance of binding force after heat treatment is seemed to be also caused by the formation of welldispersed fiber-like mineral phase which is originated from the shape of the amorphous ceramic fiber used as a raw materials.

• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.147-156
• /
• 2019

Numerical study was performed to investigate the convective heat transfer of Al₂O₃/water nanofluid flowing through the concentric double pipe counterflow heat exchangers. Hot fluid flowing through the inner pipe transfers its heat to cooling fluid flowing in the outer pipe. Effects of important parameters such as hot and cold volume flow rates, fluid type in the outer and inner pipes, and nanoparticles concentration on the heat transfer and flow characteristics are investigated. The results indicated that the heat transfer performance increases with increasing the hot and cold volume flow rates, as well as the particle concentrations. When both outer and inner pipes are nanofluids with 8% nanoparticle volume concentration, nanofluids showed up to 17% better heat transfer rate than basic fluids. Also, the average heat transfer coefficient of the base fluid for annulus-side improved by 31%. Approximately 20% enhancement in the heat exchanger effectiveness can be achieved with the addition of 8% alumina particles in base fluid. But, addition of nanoparticles to the base fluid enhanced friction factor by about 196%.