• 한국지반공학회논문집
• /
• 제34권10호
• /
• pp.17-28
• /
• 2018

캔틸레버 옹벽의 안정성 평가에서 중요한 변수는 옹벽에 작용하는 주동토압과 옹벽과 함께 움직이는 뒷굽 상부의 뒤채움토사의 무게이다. 캔틸레버 옹벽의 뒷굽 길이가 충분히 길면, 뒷굽 끝단에서의 연직면에 Rankine 토압이 작용한다고 가정하여 옹벽의 안정성을 평가해도 이론적으로 문제가 되지 않는다. 그러나 뒷굽이 짧은 캔틸레버 옹벽에 대하여 이와 같은 방법을 적용하는 것은 이론적으로 옳지 않으며, 주동토압을 실제보다 크게 산정하므로써 비경제적인 설계를 초래한다. 본 연구에서는 한계해석방법을 사용하여 캔틸레버 옹벽에 토압이 작용하는 메카니즘을 조사하고 이를 토대로 주동토압의 크기 및 합력의 위치, 뒤채움토사의 무게를 산정하였으며, 산정결과를 기존의 방법과 비교하였다. 뒷굽길이가 짧을 경우, 옹벽에 대한 안정성은 한계해석방법에 비해 기존의 Mohr원 방법은 최대 3.7%, Teng 방법은 최대 32% 크게 산정되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.335-335
• /
• 2010

한국표준과학연구원 진공센터에서는 국제규격에 바탕을 둔 저진공펌프 종합특성평가시스템을 구축하여 $1100mbar\;{\sim}\;10^{-3}mbar$ 압력 영역에서의 저진공펌프(roots, dry 등)류의 종합특성평가를 시행하고 있다. 저진공펌프 종합특성평가시스템은 국제적 절차에 따른 신뢰성을 바탕으로 구축하고 있으나, 한국표준과학연구원 진공센터 뿐만 아니라, 국내에서도 고진공 종합특성평가 시스템을 구축 하고 있지 않다. 이에 반도체/디스플레이 등 첨단 공정에서 진공 환경을 조성하는 핵심장비인 고진공펌프의 종합특성평가시스템을 개발하고자 터보펌프(TMP) 1000L/s 급의 database를 구축 하였다. 터보펌프(TMP)는 throughput method와 orifice method 두 가지 방법을 병행하여 pumping speed 측정한다. orifice method는 일종의 미세유량 측정 장치이며, 실험값과 계산값 유량의 오차 범위가 작고 신뢰성을 확보하면 throughput method 만으로 측정할 수 있다. Througput method는 $10^{-6}mbar$ 압력 이상의 영역을 측정하며, ultimate pressure 및 $150^{\circ}C$의 bake-out 을 진행하여 base pressure을 측정 할 수 있으며, $10^{-6}mbar$ 압력 이상의 pumping speed를 측정 할 수 있다. 이에 따른 정압형 유량시스템을 개발 중에 있으며, inlet pressure와 outlet pressure를 이용한 compression ratio를 측정 한다. Orifice method는 ultimate pressure와 base pressure을 측정하며, leak valve를 이용한 컨덕턴스(C)로 pressure ratio을 이용하여 유량값을 계산하며, $10^{-6}mbar$ 압력 이하의 pumping speed를 측정할 수 있다. 또한 throughput method와 orifice method의 pumping speed 뿐만 아니라 소비전력 및 소음, 진동, 온도 등 특성평가 관련 사항들의 전반적인 사항을 평가하여 터보펌프(TMP) 1000L/s 급의 database를 구축한다. 향후 예비 실험을 통한 고진공펌프의 종합특성평가시스템을 완비해 나가며, 고진공펌프 종합 특성평가시스템을 통하여 국제적으로 공인받을 수 있는 평가기준을 확립하고 그 기준에 의한 진공/기계적 성능의 전방위적인 종합특성진단과 공정대응성 평가 등 국제적 기술 신뢰성을 확보하고자 한다.

• Geomechanics and Engineering
• /
• 제8권4호
• /
• pp.523-540
• /
• 2015

Based on limit equilibrium principles, this study presents a theoretical derivation of a new analytical formulation for estimating magnitude and lateral earth pressure distribution on a retaining wall subjected to seismic loads. The proposed solution accounts for failure wedge inclination, unit weight and friction angle of backfill soil, wall roughness, and horizontal and vertical seismic ground accelerations. The current analysis predicts a nonlinear lateral earth pressure variation along the wall with and without seismic loads. A parametric study is conducted to examine the influence of various parameters on lateral earth pressure distribution. Findings reveal that lateral earth pressure increases with the increase of horizontal ground acceleration while it decreases with the increase of vertical ground acceleration. Compared to classical theory, the position of resultant lateral earth force is located at a higher distance from wall base which in turn has a direct impact on wall stability and economy. A numerical example is presented to illustrate the computations of lateral earth pressure distribution based on the suggested analytical method.

• 산업경영시스템학회지
• /
• 제34권1호
• /
• pp.90-96
• /
• 2011

The shock absorber base assembly is one of the parts in the shock absorber equipment that controls the vehicle movement. It absorbs the shock and vibration to guarantee riding stability and comfort. It demands strength, reliability and strict airtightness of the welded section because the shock absorber base assembly is a container which resists pressure and needs durability by being filled with gas and oil. However, the current engineering needs a lot of production time, has a high cost and shows a low production rate. These problem due to the eight production processes, four of which are spot welding, reinforcement welding like metal active welding (MAG), prior process of the base assembly cap and tube for precision and pressing. We will analyze the manufacturing processes of the base assembly and suggest an improved manufacturing method that uses frictional welding. The results will show that the new method of the frictional welding is better than the previous welding technique. Through the use of this concept of frictional welding, the welding conjunction will be strengthened, measurements will be more precise, and the cost and the number of processes will be reduced.

• 한국지열·수열에너지학회논문집
• /
• 제16권1호
• /
• pp.9-16
• /
• 2020

In this study, a numerical study was conducted to evaluate the performance improvement when CuO nanofluid was used in the plate heat exchanger. As a result, the heat transfer amount is increased by 5.45% when 2 vol% CuO nanofluid is used. The influence on the CuO nanofluid on the performance of heat exchanger is decreased by increasing the flow rate of working fluid. In addition, the overall heat transfer coefficient using 2 vol% CuO nanofluid decreased compared to the base fluid. However, the pressure drop and the consumption of the pump power is increased as the concentration of CuO nanofluid increased because the increase of the viscosity. These are increased up to 15.4% compared to those of the base fluid. Moreover, the performance index of CuO nanofluid is decreased by 12.6% compared to that of the base fluid.

• Journal of Welding and Joining
• /
• 제25권6호
• /
• pp.53-58
• /
• 2007

The present study examined the mechanical properties of the friction welding of shaft made of SKH51 and SM45C, of which the diameter is 12mm. Friction welding was done at welding conditions of 2,000rpm, friction pressure of 104MPa, upset pressure of 134MPa, friction time of 0.5sec to 2.5sec by increasing 0.5sec, upset time of 2 seconds. Under these conditions, a tensile test, a bending test, a shear test, a hardness test and a microstructure of weld interface were studied. When the friction time was 1.0 second under the conditions, the maximum tensile strength of the friction weld observed to be 963MPa, which is 89% the tensile strength of SKH51 base metal and 101% of the tensile strength of SM45C base metal. When the friction time was 1.0 seconds under the conditions, the maximum bending strength of the friction weld happened to be 1,647MPa, which is 78% the bending strength of SKH51 base metal(2,113MPa) and 87% of the bending strength of SM45C base metal(1,889MPa). When the friction time was 1.0 seconds under conditions, the maximum shear strength of the friction weld was observed to be 755MPa, which is 92% the shear strength of SKH51 base metal and 122% of the shear strength of SM45C base metal. According to the hardness test, the hardness distribution of the weld interface varied from Hv282 to Hv327. HAZ was formed from the weld interface to 1.2mm of SKH51 and 1.6mm of SM45C. Upon examination it was found that the microstructure became finer along with increase of friction revolution radius.

• 한국식품과학회지
• /
• 제44권2호
• /
• pp.162-167
• /
• 2012

톳으로부터 HPH를 이용해 식품에 적용 가능성이 있는 가식성 필름을 제작할 수 있었다. HPH 처리 압력의 증가는 필름의 강도와 깨짐성을 증가시켰고, 단면이 조밀하고 균일한 필름을 형성시켰다. HPH의 처리 횟수의 증가 또한 필름의 단면을 조밀하게 하였다. 개발된 톳 필름은 보고된 많은 다른 생고분자 필름들에 비해 상대적으로 강도, 깨짐성, 그리고 수분 저항력이 낮아 코팅 또는 롤을 비롯한 필름 형태로 건조 식품 또는 중간 수분 식품에 적용될 수 있는 가능성을 보여주었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2432-2437
• /
• 2007

The demand of high speed and miniaturization of electronic devices results in increased power dissipation requirement for thermal management. In this work, the effects of microchannel width, height and liquid flowrate on the cooling performances of microchannel waterblock are investigated experimentally. The microchannel waterblock considered ranged in width from 0.5 to 0.9 mm, with the channel height being nominally 1.7 to 9 times the width in each case. The experiments were conducted using water, over a liquid flow rate ranging from 0.2 to 2.0 lpm. The base temperature, thermal resistance and pressure drop increase with increasing of liquid flow rate. The measured thermal resistances ranged from 0.10 to 0.23 $^{\circ}C$/W for the channel 5.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.263-264
• /
• 2002

The tribological characteristic of several environmentally friendly lubricating base stocks was examined, and the effect of some commonly used additives on th tribological behavior of the lubricating oils was comparatively investigated on a four-ball machine. It has been found that the commercial additives including butene sulfide, wax chloride, zinc dialkyldithiophosphate and ashless P-N type agent helped to improve the friction-reducing and antiwear properties as well as the extreme pressure behavior. Non-toxic nanoscale $(CF)_x$ showed the best friction-reducing ability, though it registered relatively poor extreme pressure properties. The mechanism on friction of nano-scale material is discussed.

• Applied Science and Convergence Technology
• /
• 제24권4호
• /
• pp.84-89
• /
• 2015

The base pressure and outgassing rate of a mild steel chamber were measured and compared to those of a stainless steel chamber. A combined sputter-ion and non-evaporable getter pump with a nominal pumping speed of 490 l/s generated the base pressure of $2.7{\times}10^{-11}$ mbar in the mild steel chamber and $1.2{\times}10^{-10}$ mbar in the stainless steel chamber. The rate-of-rise measurements show that the mild steel has an extremely low outgassing rate of $2.6{\times}10^{-13}$ mbar $ls^{-1}cm^{-2}$, which is about one-order of magnitude smaller than the outgassing rate of the stainless steels. Vacuum annealing of the mild steel at $850^{\circ}C$ reduced the outgassing rate further to $8.8{\times}10^{-14}$ mbar $ls^{-1}cm^{-2}$, which was comparable to the outgassing rate of a heat treated stainless steel for extreme-high vacuum use.