• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1201-1207
• /
• 2010

As the mobile services have been increased, the PIMD(Passive Inter-Modulation Distortion) as well as the active-IMD of the CDMA system should be considered for the design of base station antenna systems, because they have an interference of the neighboring base stations. In this paper, in order to reduce the nonlinearity of current caused by the local point contact, we have investigated an influence of the combination of nuts, contact torque(kgf.cm), and the contact area on the PIMD. We propose the improvement techniques of PIMD by investigating the effects of the distance of nuts, the contact area, and the type of nuts.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.2
• /
• pp.57-65
• /
• 1995

The effects of device geometry and layout on high speed performance such as current gain outoff frequency(f$_{T}$) and maximum oscillation frequency(f$_{max}$) are of very improtant for the scaling-down of geterojunction bipolar transistors(HBT$_{s}$). In this paper AlGaAs/GaAs HBTs are fabricated by MBE epitaxial growth and conventional mesa process, and the experimental data of emitter-base geometru dependency of HBT performance are presented in order to provide the quantitative information for optimum device structure design. It is shown that f$_{T}$ and f$_{max}$ are inversely proportional to the emiter stripe width, while the low emitter perimeter/area ratio is better to f$_{T}$ and worse ot f$_{max}$. It is also demonstrated the f$_{T}$ and f$_{max}$ are highly improved by the emitter-base spacing reduction resulting in less parsitic effects. As the result f$_{T}$ of 42GHz and f$_{max}$ of 23GHz are obtained for fabricated HBT with emitter area of 3${\times}20^{\mu}m^{2}$ and E-B spacing of 0.2$\mu$m.m.m.

• The Korean Journal of Air & Space Law and Policy
• /
• v.21 no.2
• /
• pp.207-230
• /
• 2006

It should be noted that current rules and provisions of the law, such as the act of military air base and the act of the construction, do not provide a fairly good solution regarding the conflict between the company and the air force. The act of military air base does not have the jurisdiction on the matters occurring outside the edge of the flight safety zone. Freezing measure about the construction permit is not suitable for this case. A sort of policy or revision of the law will be needed to foster the transaction between parties in question which may be useful for enhancing overall efficiency.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.10a
• /
• pp.181-182
• /
• 2012

This study aims to present about structural marina floats to yacht enhancement. Yacht marina facilities take long time and huge budget. The current ministry of land, transport and maritime affairs is planning to select an optimal design and spot for marina float base to yacht enhancement using Mokpo harbor. First, this paper focuses on marine floatation system to find requirements of selection. Second it points out sample structural marina floats in practice. Finally, this paper presents some recommendations for developing plan and method.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1139-1152
• /
• 2018

Many studies on the application of stainless steels as structural materials in buildings and infra-structures have been performed thanks to superior characteristics of corrosion resistance, fire resistance and aesthetic appeal. Experimental investigation to estimate the ultimate strength and fracture mode of the fillet-welded connections of cold-formed austenitic stainless steel (STS304L) with better intergranular corrosion resistance than that of austenitic stainless steel, STS304 commonly used has carried out by authors. Specimens were fabricated to fail by base metal fracture not weld metal fracture with main variables of weld lengths according to loading direction. All specimens showed a block shear fracture mode. In this paper, finite element analysis model was developed to predict the ultimate behaviors of welded connection and its validity was verified through the comparison with test results. Since the block shear behavior of welded connection due to stress triaxiality and shear-lag effects is different from that of bolted connection, stress and strain distributions in the critical path of tensile and shear fracture section were investigated. Test and analysis strengths were compared with those by current design specifications such as AISC, EC3 and existing researcher's proposed equations. In addition, through parametric analysis with extended variables, the conditions of end distance and longitudinal weld length for block shear fracture and tensile fracture were suggested.

• Current Optics and Photonics
• /
• v.6 no.3
• /
• pp.252-259
• /
• 2022

In this paper, a dual-function dynamically tunable metamaterial absorber is proposed. At frequency points of 1.545 THz and 3.21 THz, two resonance peaks with absorption amplitude of 93.8% (peak I) and 99.4% (peak II) can be achieved. By regulating the conductivity of photosensitive silicon with a pump laser, the resonance frequency of peak I switches to 1.525 THz, and that of peak II switches to 2.79 THz. By adjusting the incident polarization angle by rotating the device, absorption amplitude tuning is obtained. By introducing two degrees of regulation freedom, the absorption amplitude modulation and resonant frequency switching are simultaneously realized. More importantly, dynamic and continuous adjustment of the absorption amplitude is obtained at a fixed resonant frequency, and the modulation depth reaches 100% for both peaks. In addition, the sensing property of the proposed MMA was studied while it was used as a refractive index sensor. Compared with other results reported, our device not only has a dual-function tunable characteristic and the highest modulation depth, but also simultaneously possesses fine sensing performance.

• Educational Technology International
• /
• v.9 no.1
• /
• pp.79-96
• /
• 2008

The issue of connection between entities has a lengthy history in educational research, especially since it provides the necessary bridge between base and target in analogical transfer. Recently, the connection has been viewed through the application of technology to bridge between sequences in order to be cognitively useful. This study reports the effect of sequence type (AT vs. TA) and connection type (fading vs. popping) on the achievement and analogical transfer in a multimedia application. In the current research, 10th -grade and 11th -grade biology students in Korea were randomly assigned to five groups to test the effects of presentation sequence and entity connection type on analogical transfer. Consistent with previous studies, sequence type has a significant effect: analogical transfer performance was better when base representations were presented first followed by target representations rather than the reverse order. This is probably because presenting a familiar base first helps in understanding a less familiar target. However, no fully significant differences were found with the entity connection types (fading vs. popping) in analogical transfer. According to the Markman and Gentner's (2005) spatial model, analogy in a space is influenced only by the differences between concepts, not by distance in space. Thus connection types fail on the basis of this spatial model in analogical transfer test. The findings and their implications for sequence and connection research and practice are discussed. Leveraging on the analogical learning process, specific implications for scaffolding learning processes and the development of adaptive expertise are drawn.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.10
• /
• pp.1108-1120
• /
• 1990

The present study is to develop an intelligent control system for flexible manufacturing system, which is suitable for a variety of manufacturing types with smaller production rates. The controller is designed to integrate heuristic rules with optimization techniques for loading as well as flow rate of parts and ultimately meeting performance indices. The control function implemented by an optimization technique is to calculate short term production rates of parts. The heuristic control determined by production rules requires knowledge base to evaluate selected loading alternatives according to short term production rate and current process information, and also to determine final decision pertaining to loading. In this case, the knowledge base is constructed using the rules for evaluating alternatives, decision criteria, and flow control of parts in manufacturing system. The database is formulated by means of managing and updating current process information. A graphic system to monitor current status of the function and operation of manufacturing system is developed, and computer simulation is carried out to evaluate the performance of the proposed controller.

• Journal of the Korean Institute of Gas
• /
• v.11 no.2 s.35
• /
• pp.31-36
• /
• 2007

In order to study on the corrosion characteristics of STS 304 pipeline steel weldment for gas cooling & heating system. the electrochemical polarization test and corrosion test by impressed potential in 0.5M $H_2SO_4+0.01M$ KSCN solution was carried out. Also, SEM and hardness of welding zone was measured. And then passive behavior, corrosion behavior by the impressed potential and SEM aspect and hardness behavior of base metal(BM) and heat affected zone(HAZ) for STS 304 pipe were investigated. The main results are as follows: 1) The critical anodic current density of heat affected zone(HAZ) is drained more highly than that of base metal(BM), and primary passive potential of HAZ become higher than that of BM. 2) The passive current density of TUE is drained more highly than that of BM, and passive region of BM become bigger than that of HAZ. 3) By the impressed potential, the current density of HAZ is drained more than that of BM.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1428-1435
• /
• 2019

The total ionizing dose (TID) and non ionizing energy loss (NIEL) effects of 100 MeV phosphorous ($P^{7+}$) and 80 MeV nitrogen ($N^{6+}$) ions on 200 GHz silicon-germanium heterojunction bipolar transistors (SiGe HBTs) were examined in the total dose range from 1 to 100 Mrad(Si). The in-situ I-V characteristics like Gummel characteristics, excess base current (${\Delta}I_B$), net oxide trapped charge ($N_{OX}$), current gain ($h_{FE}$), avalanche multiplication (M-1), neutral base recombination (NBR) and output characteristics ($I_C-V_{CE}$) were analysed before and after irradiation. The significant degradation in device parameters was observed after $100MeV\;P^{7+}$ and $80MeV\;N^{6+}$ ion irradiation. The $100MeV\;P^{7+}$ ions create more damage in the SiGe HBT structure and in turn degrade the electrical characteristics of SiGe HBTs more when compared to $80MeV\;N^{6+}$. The SiGe HBTs irradiated up to 100 Mrad of total dose were annealed from $50^{\circ}C$ to $400^{\circ}C$ in different steps for 30 min duration in order to study the recovery of electrical characteristics. The recovery factors (RFs) are employed to analyse the contribution of room temperature and isochronal annealing in total recovery.