• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.796-808
• /
• 2007

In this paper, two novel compact microstrip bandstop filters using complimentary split ring resonators(CSRRs) and spiral resonators is proposed. The first one is the bandstop filter using an array of CSRRs etched on the center line of a microstrip. The bandstop is due to the presence of negative effective permittivity and positive permeability near resonant frequency which prevent the wave propagation. The second on is the bandstop filter using an array of spiral resonators etched on the center line of a microstrip. The bandstop is due to the self-resonance of spiral circuit. We have achieved controllable resonance frequency and bandwidth, super compact dimension, low insertion losses in the passband and high level of rejection in the stopband with sharp cutoff. The electrical sizes of two proposed filter are very small. Additionally, they can be easily fabricated and compatible with MMIC or PCB technology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1333-1338
• /
• 2008

In this paper, RF varactor diode are applied to the design of miniaturized and tunable bandstop filter. The proposed bandstop filter is based on a Defected Ground Structure(DGS) section topology. The designed tunable bandstop filter can achieve a significant size reduction by with loading capacitance component of varactor diode. It is observed from the measured results that the proposed tunable bandstop filter shows a wide tuning range of 42.9 % from 1.01 GHz to 1.99 GHz. The rejection level in the stopband is higher as the number of DGS section increases. In case of the proposed tunable bandstop filter with two DGS sections, the rejection level of the filter is better than 20 dB in the stopband during the tuning. In this case, the maximum insertion loss in the lower passband is 0.5 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1122-1128
• /
• 2008

A novel tunable bandstop filter was proposed. It is composed of a right-handed transmission line, which has lowpass characteristics, and a left-handed transmission line which has highpass characteristics. Dispersion relations for the unit cells of RHTL and LHTL were derived by the method of ABCD parameter analysis. Varactor diodes and chip inductors were used to make the unit cells of RHTL and LHTL. A tunable bandstop filter was designed and fabricated by the parallel connection of RHTL and LHTL. The measured results of the proposed tunable bandstop filter are agreed well with the simulated results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.1
• /
• pp.1-7
• /
• 1988

A new type broadband channel dropping filter which has a potential use as a millimeter-wave multiplexer has been realized by properly connecting 3-dB directional couplers and bandstop filters. 90\ulcorner3-dB directional couplers have been designed using two nonuniformly coupled dielectric image guides, while bandstop filters with Chebyshev passbands have been designed using dielectric image-guide grating structure. Effective dielectric constant method has been aplied to the image-guide dispersion analysis and to the design of bandstop gratings and 3-dB couplers. Experimental results in excellent agreement with computed responses are demonstrated.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2392-2394
• /
• 2005

This paper presents a tuneable bandstop resonator with two possible configurations, it can be used to tune its center frequency, or it can be used to tune its bandwidth. The tuneable bandstop resonator has potential application in microwave communications receivers, where it can be used to tune out interfering signals. The proposed resonator is comb actuated, where the resonator's displacement produces different values of frequency or bandwidth, this is achieved by decoupling electromagnetic energy from a main transmission line. The proposed fabrication process for the resonator is by anodic bonding pyrex glass and tow resistivity silicon, where the comb resonator structure is patterned by deep reactive ion etching (DRIE). This paper presents the resonator and actuator design in both configurations, as well as the fabrication process intended for its development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.283-289
• /
• 2003

In this paper, we proposed novel multilayer photonic bandgap(PBG) structure using DSL(Descended Signal Line). From measurement result, the proposed PBG structure using DSL is reduced 72 % at size and increased 13 % at bandwidth compared to typical multilayer DGS(Defected Ground Structure). It is also reduced 42 % at size and increased 23 % at bandwidth compared to PBG structure using EGP(Elevated Ground Plane). In case of measurement for manufactured six PBG patterns, all patterns have the same cutoff frequency and bandstop characteristics. So it can be used for bandstop filter having very precise tolerance of below 300 MHz at 20 ㎓ if it is applied to real product and this filter will be useful for small microwave integrated circuit and module development.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.3
• /
• pp.439-444
• /
• 2020

In this paper, the analysis of the FSCS (frequency-selected coupling structure) as the coupling coefficient and multi-stage FSCS for enhanced bandstop bandwidth is suggested. The FSCS is composed by the connected coupled-line and open-stub. Basically, the resonance frequency of the FSCS is given by the electrical length of the stub, and the bandwidth is controlled by the coupling coefficient. Multi-stage FSCS is made by addition of another FSCS with the half electrical length. Manufactured bandstop filter using 3 stage FSCS is measured with the stopband of 177.3% and the maximum return loss of 1dB.

• ETRI Journal
• /
• v.32 no.1
• /
• pp.148-150
• /
• 2010

This letter presents the design of a compact bandstop filter (BSF) operating at two frequencies. The proposed BSF consists of open-ended stepped impedance resonators (OSIR) and an end-shorted parallel-coupled microstrip line (E-PCML). The OSIRs are used to achieve the impedance-controlled stopband positions. The wide BSF bandwidths are achieved through enhanced coupling of the E-PCML. Explicit design guidelines are derived using a lossless transmission line model. To validate theoretical predictions, a prototype dual-band BSF operating at 900 MHz and 2,100 MHz with fractional bandwidths of 72% and 36%, respectively, is implemented in microstrip.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.614-618
• /
• 2007

A miniaturized bandstop filter (BSF) is introduced in this paper. The filter consists of one meander spurline and a pair of capacitively loaded stubs. The meander spurline with low resonant frequency and improved slow-wave factor exhibits excellent resonant bandgap characteristics which can be modeled by a longitudinally coupled resonator. The design of the proposed microstrip BSF is presented, and its performance is measured. Measurements show that there is a stopband from 2.3 to 5.6 GHz with $S_{21}$ less than -20 dB. The total length of this BSF equals 23 mm.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2389-2391
• /
• 2005

In this paper, a compact S type resonator is presented, where the proposed resonator is surface micromachined over transmission lines or other resonators, in order to obtain a wide range of possible electromagnetic couplings. The structure has been applied in two compact, bandstop and bandpass filters with moderate fractional bandwidths (FBW) of 20% and 25% respectively. The bandstop filter presented, was designed by the combination of two design methods in order to obtain the proposed fractional bandwidth, where traditionally, coupled resonator bandstop filters have been used for narrow stopbands. The bandpass filter illustrates the use of the proposed suspended resonator structure to obtain a wide range of electric type coupling coefficients, and external quality factors for the filter. This paper describes the design methodology, concepts and fabrication method proposed for the design of these filters.